BAP- 2861R Quadra 60 X 32 Right Corner Bathtub Instruction Manual

BAP- 2861R Quadra 60 X 32 Right Corner Bathtub

Product Information

Specifications

• Product Name: BATHTUB BAIGNOIRES
• Model Number: BAP-2861R-643260
• Installation Guide Date: 27/03/2023

Product Usage Instructions

Required Tools

• Drill
• Sealant (1 tube)
• Level
• Utility Knife
• Square
• Shims
• Drop Cloth
• Pencil
• Drill Bit 3/16 (5mm)
• Screws 1 1/4 (zinc or stainless; panhead or roundhead)
• Phillips Bit (with extension bit holder)

Installation Instructions

• Step 1:
  Make sure the studs are straight and square.

• Step 2:
  Use a level and a bracket to ensure the bathtub is straight and perpendicular.

• Step 3:
  Drill 3/16” holes at the stud locations on top flanges. Ensure the gap between flanges and studs is less than 1/8”.

• Step 4:
  Install the drain onto the tub and secure the tub with the studs. Apply silicone sealer around all external joints of the bath and leave it to dry for at least a few hours.

• Step 5:
  For regular cleaning, use only mild detergents or warm soap with water. Rinse surfaces after cleaning.

FAQ

• What does the warranty cover?
  The warranty coverage includes certain parts for 1 year, others for 2 years, and specific components for 10 years.

• What are the exclusions from the warranty?
  Exclusions from the warranty may include damages caused by improper installation, misuse, or unauthorized repairs.

BEFORE STARTING

OUR PRODUCTS ARE CAREFULLY INSPECTED IN OUR WAREHOUSE AND PACKAGED FOR SHIPPING. ONLY REMOVE THE PROTECTIVE FILM AT THE VERY END OF THE INSTALLATION TO ENSURE MAXIMUM PROTECTION. (EXCEPT WHERE BATH SURFACES WILL BE IN PERMANENT CONTACT WITH ANOTHER SURFACE (I.E., FAUCETS, ETC.). IT IS VERY IMPORTANT THAT YOU CAREFULLY INSPECT THE PRODUCT BEFORE INSTALLATION. IF A PRODUCT IS DEFECTIVE, PLEASE CONTACT THE COMPANY BEFORE INSTALLATION. THE INSTALLER WILL BE HELD RESPONSIBLE FOR ANY BREAKAGE OR DAMAGES FOLLOWING THE USE OF A DEFECTIVE PRODUCT. TO PROTECT THE UNIT DURING INSTALLATION, PLACE CARDBOARD IN THE BOTTOM OF THE BATHTUB. VERIFY THAT THE BATHROOM FLOOR IS LEVELED AND STRONG ENOUGH TO SUPPORT A MINIMUM WEIGHT OF 1500 LBS. REINFORCE THE EXISTING FLOORING IF NEEDED. THE DRAIN IN YOUR BATHTUB MAY BE TO THE LEFT, THE MIDDLE OR THE RIGHT. VERIFY THE DRAIN LOCATION BEFORE DRILLING A HOLE IN THE FLOOR ACCESS PANEL MUST BE FORESEEN NEAR THE PLUMBING, PUMP AND/OR CONTROL BOXES TO TAKE THEM EASILY APART AND/OR REPAIR THESE COMPONENTS. THE WHIRLPOOL/THERAPEUTIC SYSTEMS MUST BE CONNECTED BEFORE THE FINAL INSTALLATION (SEE THE INSTALLATION AND USER’S GUIDE FOR WHIRLPOOL/THERAPEUTIC).

REQUIRED TOOLS

Dimension

BAP-2861R

• INSTRUCTIONS ARE TO BE PRESERVED BY FINAL USER.
• READ CAREFULLY BEFORE PROCEEDING WITH INSTALLATION.

INSTALLATION INSTRUCTIONS

Step 1:
Make sure the studs are straight and square.

Step 2:
After carefully verifying the drain location, drill the drain hole.

Picture for reference only. For accurate measures and installation, you need a certified plumber.

Step: 3.
If the floor is not flat or level, it is recommended to put down a mortar bed where the base will be positioned.

Step: 4.
Make sure all the legs of the tub are entirely touched on the floor. If not, adjust them set the level or use a mortar bed for proper installation.

Step 5:
Use a level and a bracket to make sure that the bathtub is straight and perpendicular.

NOTE:
Place a small amount of water in the tub to make sure that the water flows into th tub and not to the ground.

The bathtub bottom must be in contact with a perfectly straight and level surface.

Step 6:
Drill 3/16″ holes at the stud locations on top flanges

Step 7:
Install the drain onto the tub.

Step 8:
Secure the tub with the studs. Place a cardboard or drop cloth inside the tub, stand inside to press it to the floor then securing to wall studs. Secure flanges to studs with 1 1/4″ screws.

Do not overtight screws as it will crack the flange.

Step 9:
Apply silicone and remove the protection film. After the installation is completed, apply silicone to all outer edges and where the base and the wall meet.

Apply silicone sealer around all external joints of the bath and leave to allow it to dry for at least 24 hours.

For regular cleaning use only mild detergents or warm soap and water. Use only non-abrasive cloth or sponge. Always rinse surfaces after cleaning. Before using cleaning products, test a small inconspicuous area.

DSBR6432C-CL
32″ x 60″ Rectangular Pass Bathtub Screen

Dimension of shower door:
(765~790) x (1524-1494) x 1400mm(H) / (30″~31″) x (60″~58-7/8″) x 55″(H) Profile adjustment: +25mm/1″

• Rail adjustment: -30mm/-1-1/8″

General Information
Please inspect the product immediately upon receipt for transit damage, missing packs/parts or manufacturing faults. Damage reported later cannot be accepted. Please handle the product with care avoiding knocks and shock loading to all sides and edges of the glass.

Notes: Safety glass can not be re-worked

• Please read these instructions carefully before the start of installation.
• Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
• Note: This product is heavy and may require two people to install.

Aftercare instructions
After use, your shower should be cleaned with soap and water. This is particularly important in hard water districts where insoluble lime salts may be deposited and allowed to build up. Cleaners of a gritty or abrasive nature should not be used. Care should be taken to avoid contact with strong chemicals that can be used but with caution, if in doubt contact the manufacturer of the cleaner in question.

Please keep these instructions for aftercare and customer service details.

Tools Required

Assembly Drawing

Installation Steps

Step 1
PLACE CENTER OF WALL JAMB ON THE LINE

Step 2
LEVEL AND MARK THE LOCATION OF THE WALL JAMB HOLES ON THE WALL

Step 3
DRILL , SILICONE AND INSTALL WALL PLUGS ON THE WALL

Step 4
INSTALL THE WALL JAMB

Step 5
TEMPORARILY INSTALL THE RETURN PANEL AND LEVEL

Step 6
CUT THE LENGTH OF THE THRESHOLD

Step 7
ADJUST THE BOTTOM GUIDE ON THE BASE

Step 8
MARK THE PLACEMENT OF THE THRESHOLD, BOTTOM GUIDE AND U-CHANNEL

Step 9
TEMPORARILY PLACE THE THRESHOLD AND BOTTOM GUIDE ON THE BASE

Step 10
MARK THE PLACEMENT OF THE THRESHOLD AND BOTTOM GUIDE

Step 11
CUT THE THRESHOLD GASKET

Step 12
INSTALL THE THRESHOLD GASKETS

Step 13
INSTALL THE BOTTOM GUIDE

Step 14
DRAW A PARALLEL LINE ALONG THE BASE USING THE BOTTOM GUIDE CENTER AS REFERENCE

Step 15
DRAW A LINE ALONG THE WALL ON BOTH SIDE USING A LEVEL

Step 16
INSTALL THE WALL MOUNT BRACKET ON THE RETURN PANEL

Step 17
CALCULATE THE LENGTH OF THE RUNNING RAIL REQUIRED USING THE FORMULA PROVIDED

Step 18
TEMPORARILY INSTALL THE WALL MOUNT BRACKET

Step 19
INSERT THE RUNNING RAIL INTO THE RETURN MOUNT BRACKET

Step 20
MARK THE PLACEMENT LINE FOR THE WALL MOUNT BRACKET ON THE WALL AND REMOVE THE RUNNING RAIL

Step 21
PLACE THE WALL MOUNT BRACKET ON THE WALL AND MARK THE HOLE LOCATION

Step 22
DRILL, APPLY SILICONE & INSERT THE WALL PLUGS

Step 23
SECURE THE WALL MOUNT BRACKETS TO THE WALL

Step 24
ADD THE RUNNING RAIL AND THE WALL MOUNT COVERS

Step 17
INSTALL THE BOTTOM DOOR GASKET ON THE INTERIOR PANEL

Step 18
INSTALL THE ROLLERS ON THE INTERIOR PANEL

Step 19
INSTALL THE TOWEL BAR ON THE INTERIOR PANEL

Step 20
INSTALL THE INTERIOR PANEL

Step 21
INSTALL THE ROLLERS ON THE EXTERIOR PANEL

Step 22
INSTALL THE TOWEL BAR ON THE EXTERIOR PANEL

Step 23
INSTALL THE EXTERIOR PANEL

Step 24
INSTALL THE ANTI-JUMP ON THE EXTERIOR ROLLERS

Step 25
INSTALL THE SIDE GASKET ON THE DOOR PANELS

Step 26
ADJUST THE DOOR PANELS

Step 27
INSTALL THE ROLLER CAPS

Step 28
SEAL THE SHOWER UNIT

LIMITED WARRANTY

By choosing a BATO product, a leader in the plumbing industry distributing its products across North America, you are sure to make the right choice. On top of the quality materials that are used to make their products, BATO’s advanced manufacturing processes also benefit its products’ quality and longevity. To attest to this, they decided to offer their customers a beneficial warranty.

We certify that our products will meet your needs with their style, but also with their manufacturing quality. To make sure that they are reliable and safe, each product was carefully inspected, tested and approved during the quality control process that is in place.

To whom does this warranty apply?
BATO offers a 10-year limited warranty from the date of purchase, exclusive to the first buyer as long as he/she resides in the same property. This warranty applies to all BATO bathtubs. The warranty is intended for residential and/or domestic use.

Care instructions
Clean the product with water and a mild detergent. Abrasive or corrosive cleaners, steel wool, acetone, dry cleaning products or ammonia compounds must never be used to clean the product. If a bath mat is used, it must be removed right after each use. We recommend the use of cleaning products that are made of acrylic specifically.

What is covered by the warranty?

From the date of purchase.

Should any manufacturing defects are not covered by the warranty, the product will need to be inspected before following through with the claim. Without that verification, the brand will assume no charge and/or responsibility.

What are the exclusions?

• This warranty applies to all BATO products purchased on or after January 1st, 2018.
• The warranty doesn’t apply if the product is damaged as a result of misuse, overuse or non-residential use, neglect, lack of maintenance, or the use of corrosive or abrasive products, regardless of the person who did those damages. The warranty does not cover shipping and labour costs. The warranty does not apply to the normal tear and wear of the goods.
• The warranty doesn’t cover the damages caused by the acts of God or breakage resulting from a shock or mishandling, regardless of the part played by the buyer or the installer. It also excludes the damages caused by an improper installation.
• BATO doesn’t cover damages caused by a water leak, even if they result directly or indirectly from a product defect, except where the applicable legislation does not allow any exclusion or limitation following indirect or consequential damages.
• It is fair to say that if the product has a manufacturing defect, it will show as soon as it is installed or shortly after. However, a leak caused by an improper installation could happen a long time after. Therefore, it is strongly advised to have it done by a professional.

All warranty claims must include the invoice copy.
Should a part or product component be defective or the finish damaged following normal domestic and residential use, BATO commits to replacing the defective part(s) with the first buyer only. BATO could also, in its sole discretion, commit to offer a full replacement. No indemnity shall be claimed for loss of enjoyment of life, loss of income or losses caused by water.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>