Tucok 012S Adults 4K Drones with Camera User Manual

193
User ‘S Manual

012S Adults 4K Drones with Camera

193 E Quick Start Guide

Learn more about drones before flying

• For details, please refer to the instruction manual.
  Please ensure that the drone and remote control batteries are fully charged before the flight.

  1. Precautions for using the ptz camera:
     Use note:
     A. Please remove the protective cover from the camera before starting this product.
     B. Do not touch the gimbal camera when starting this product!
     Because the gimbal is automatically calibrated at the moment of power-on, if you touch it without authorization, it will cause the gimbal to fail to calibrate properly, and the gimbal calibration function may be damaged! Please do not touch the camera while the gimbal is being calibrated when the power is on!

  2. Remote control with drone
     Turn on the power of the drone first and then turn on the power of the remote control. After the remote control of the drone is powered on, wait for about one minute to automatically pair the frequency.
     Note: The drone is placed on the flat ground directly in front of the remote controller, and the remote controller makes a “beep” after the frequency is successfully connected, and the drone and the remote controller are successfully linked. ! Important Hint:
     You must first correct the geomagnetism and then the gyroscope, otherwise it will affect the normal use.

  3. Geomagnetic correction
     Place the drone on a horizontal plane, press and hold the indicator button (as shown in Figure 1) for 5 seconds, and then the remote control will make a beeping sound to perform geomagnetic correction. At this time, the lights of the aircraft will flash quickly, pick up the drone and press (Figure 2) to indicate clockwise Rotate 3-5 circles, the remote control will make a beeping sound, and then rotate the camera downwards (Picture 3) for 3-5 circles, the remote control will make a beeping sound, the geomagnetic calibration is completed!

  4. Drone gyroscope and gimbal level calibration Place the drone on a level surface, press and hold the remote control for 5 seconds to make a beeping sound, press the button as shown in the figure, and the calibration is successful.

  5. Flight mode switch
     Note: The default GPS mode (GPS MODE) is when the product is powered on. The UAV can only unlock the motor but cannot take off without reaching 8 satellites. To take off, you need to switch the indoor mode before the satellite positioning is completed. Press and hold the headless mode key for 5 seconds (the switching method is shown in the right figure). After the switch is successful, the remote control will emit a click, At this time, the UAV will not have all the functions related to GPS (one key return, low power return, runaway return, etc.) Pay attention to the flight altitude distance to avoid the loss of UAV!
     Note * After GPS positioning is completed, you cannot switch to ATTI MODE indoor mode. To switch, you need to shut down and restart the drone and remote control.

  6. NORMAL MODE smooth mode switch SPORT MODE sports mode
     Note: The product is powered on by default in the NOEMAL MODE stable mode. The drone has obstacle avoidance functions. If you switch to the SPORT MODE sport high gear mode, the drone obstacle avoidance function will automatically fail. At this time, the drone will not have all obstacle avoidance functions.
     Need to pay attention to the flight height and distance, pay attention to the surrounding flying environment, to avoid damage to the drone due to improper flight.

  7. Drone unlockAt this time, the throttle stick and the directional stick are pushed to the lower left corner and the lower right corner at the same time (Figure 1), or pushed to the lower right corner and the lower left corner (Figure 2) at the same time, the unlocking can be completed, and the motor can fly after starting.

  8. Description of remote control antenna
     In order to make the transmission signal between the remote controller and the aircraft better, the remote control distance is longer, and the flight distance is longer, please use the product according to the following instructions.

  9. Drone and remote control battery charging How to take out the drone battery Press the battery latch and remove the battery backwards.
     Keep fingers and machine clean and dry before operation, otherwise the battery may not be slipped out. Remote control and drone battery charging Tips:
     ● Insert the plug in the correct way.
     ● It is recommended to use 5V 1-2A adapter for charging.
     ● After the drone is used, please turn off the battery power and take it out in time, and place it in a cool place to avoid heat and damage caused by the drone for a long time.

  10. Know Your Remote APP
      (1) Scan the QR code to download and install the APP, and support Google iOS and Android.| |
      ---|---|---
      http://app.hy-chip.com/xl-super_download.html| https://play.google.com/store/apps/details?id=com.hy.xil_fly| https://apps.apple.com/cn/app/xl-super/id1644098718

(2) Expand the antenna and handle, connect the adapter cable to the type c interface on the right of the remote control, and install the mobile device.
be careful:
The remote control is installed with the adapter of the typec interface by default.
Please replace the adapter according to the type of mobile device interface. The connector at the bottom of the remote control is only used for charging the remote control, not for image transmission connection data.

193 E Flight Tutorial Video

The default GPS MODE when starting up: GPS mode, when you enable GPS mode, pay attention to the open space without tall buildings and high-voltage wires
Use it in places where there is signal interference.
ATTI MODE indoor mode: optical flow mode. When using this mode, you need to turn off the GPS function before taking off.

|
---|---
http://nnti.cn/qr/ui6yhudbdubdyd8.html| http://nnti.cn/qr/hu121bd522yd8h1.html

ATTI MODE indoor mode is applicable to indoor open places. After the frequency of the UAV and the remote control are aligned and the geomagnetism and gyroscope are calibrated, ATTI MODE is displayed on the remote control display. At this time, the UAV will automatically perform GPS search and positioning, and the automatic activation of the protection program will not be able to take off. You need to press the headless mode key for 5 seconds, and the remote control will emit a “drip” sound, which means that the takeoff can be unlocked after the GPS function is turned off.
(Note: Mode1 optical flow mode does not have a series of GPS functions such as low power return, one-button return, etc. Please pay attention to the flight distance and altitude when using)

Press and hold the headless mode key for 5 seconds, and the remote control will make a “drip” sound, indicating that the GPS function is turned off
Mode2: GPS / optical flow dual mode, suitable for outdoor open areas without signal interference. After the drone and remote control are linked, the geomagnetic and gyroscopes are corrected, the display on the remote control changes from Mode0 to Mode1, at this time the drone GPS satellite search and positioning automatically (Drone search should be placed in an open area when searching for satellites, and there should be no obstructions such as high- rise buildings or cars, high-voltage power lines, or the drone will not be able to complete GPS satellite search and positioning), etc. The number reaches about 10, the positioning is completed, the remote control emits a “dip”, and the display  requency of the remote control changes from Mode1 to Mode2 to indicate that the positioning is successful, and the takeoff can be unlocked. (Note: GPS mode does not complete GPS Before positioning, the drone automatically enables the protection program and cannot take off)

193 User manual GPS Smart Drone

Important notices and safety guidelines
You are welcome to purchase our products. In order to make it easier and more convenient for you to use this drone, please read this manual carefully before operating, and please keep this manual in a safe place for future reference for adjustment and maintenance.
Disclaimer

• This product is not a toy, but a precision device that integrates mechanical, electronic, aerodynamics, high-frequency emission and other professional knowledge into one. It requires correct assembly and debugging to avoid accidents. The product owner must use a safe method to operate the control; improper operation may cause serious personal injury or property damage.

• This product is suitable for people who have experience in operating model drones and are not less than 14 years old.

• If you have any questions about use, operation, maintenance, etc., please contact your local dealer or our company. Our company and the seller are not responsible for any loss and damage caused by improper use or operation and human injury.

• The product contains small parts. Keep it out of the reach of children to avoid the danger of accidental eating or suffocation.

• You are responsible for this aircraft to ensure that it will not cause harm to the person and property of others.
  Laws And Regulations
  To avoid possible injury and loss from illegal activities, the following items must be observed:

• Never fly near a manned aircraft, and land immediately if necessary.

• It is forbidden to use aircraft on the scene of large-scale events. These venues include but are not limited to: sports competition venues and concerts.

• Never fly in areas prohibited by local laws.

• Ensure that the aircraft will not affect the large manned aircraft on the route when flying. Always be vigilant and avoid other aircraft.

• To ensure the requirements of the magnetic environment of aeronautical radio stations. During the radio control order issued by the relevant state departments, within the area, the use of the model remote control should be stopped as required.

Safety Precautions

The remote control model UAV is a high-risk commodity, so keep away from the crowd when flying. Improper assembly or damage to the body, poor electronic control, and unfamiliar operation can all lead to unpredictable accidents such as damage to the drone or personal injury. Operators must pay attention to flight safety and understand all responsibilities for accidents caused by their negligence.

• Keep away from obstacles and people
  The remote control drone has uncertain flight speed and status when flying, and there is potential danger. When flying, you must stay away from crowds, high-rise buildings, high-voltage power lines, etc., and avoid flying in bad weather such as wind and rain. The commissioning and installation of the drone must be operated strictly in accordance with the operating instructions. Pay attention to maintaining a distance of 1-2 meters from the user or other people when the drone is flying. And the body, causing injury.

• Keep away from humid environment
  The interior of the drone is composed of many precision electronic components and mechanical parts. Therefore, it is necessary to prevent the drone from getting wet or water entering the body, so as to avoid accidents caused by mechanical and electronic component failure. During maintenance, please wipe the surface stain with a clean cloth.

• Avoid manipulation alone
  The remote control drone control technique has certain difficulties in the early stages of learning. To avoid flying alone, you need the guidance of experienced people.

• Proper use of this product
  Please use our original parts for modification or maintenance to ensure the safety of flight. Please operate and use the product within the scope permitted by the product function, and shall not be used for any illegal purpose other than safety regulations.
  Safe operation
  1. Please operate the remote control drone according to your state and flying skills. Fatigue, mental retardation, or improper operation will increase the risk of accidents.
  2. Do not use near your ears! Misuse can cause hearing damage.
  3.After the drone is used, please turn off the battery power and take it out in time, and place it in a cool place to avoid heat and damage caused by the drone for a long time.

• Keep away from high-speed rotating parts
  When the drone rotor is rotating at high speed, please keep the pilot, surrounding people and objects away from the rotating parts to avoid danger and damage.

• Keep away from heat sources
  The remote control drone is composed of metal, fiber, plastic, electronic components and other materials, so it should be kept away from heat sources as much as possible to prevent sunlight, deformation and even damage due to high temperature.

• Environmental requirements
  Discard this product at will, which may have an impact on the environment. Please recycle properly in accordance with local laws and regulations.

Product Description

Product Configuration
Packing List

Drone Part Names

[1] LED light [2] visual obstacle avoidance [3] HD camera [4] wind blade
[5] motor [6] power indicator [7] intelligent lithium battery [8] power switch

1. Propeller installation
   Please make sure that all propellers are installed in the correct orientation as shown in the figure below. If the installation is incorrect, the aircraft will not fly normally.

2. Aircraft lithium battery

-Press and hold the power button for 3 seconds to turn on, and then press and hold the power button for 3 seconds to turn off.
-Once the battery is in a low state, there is one light left in the battery power indicator. Please charge the battery immediately to avoid damage caused by excessive discharge of the battery.
Battery installation
Press the battery button down, and then push the battery into the drone battery holder. After the installation is complete, the battery clip will pop up and check to ensure that the battery is in place.

Warm reminder : If the battery is not installed in place, it is likely to cause an aerial power failure and fall accident of the unmanned aerial vehicle.
After the UAV is used, please turn off the battery power in time and take it out, and properly place it in a cool place to prevent the UAV from heating and causing damage due to long-time electrification.
Note: If the UAV does not take off for more than 10 minutes when it is powered on, the battery will start the protection program and automatically power off!
Battery removal
Press the battery latch and remove the battery backwards.
Keep fingers and machine clean and dry before operation, otherwise the battery may not be slipped out.

Drone battery charging

Tips:

• Insert the plug in the correct way.
• It is recommended to use 5V 1-2A adapter for charging.
• When charging the rechargeable battery, do not use it for children alone. It must be carried out under the supervision of an adult. It must be kept away from flammable materials during charging. The guardian should not leave the aircraft outside the surveillance range during charging.
• Do not short circuit or squeeze the battery to avoid explosion.
• The power supply terminals should not be taken out of the model, and the terminals should not be short-circuited; do not short-circuit, disassemble or throw the battery into fire; do not place the battery in high temperature and heat places (such as in a fire or near an electric heating device).
• The model can only use the recommended charger. Regularly check the charger’s wires, plugs, shells and other parts for damage. If you find any damage, stop using it until the repair is complete.
• The charger is not a toy; the charger can only be used indoors.
• The battery must be charged and stored after the flight. If not in use, it is recommended to charge the battery at least once every 3 months to avoid over-discharging the battery and permanently damaging the battery.

Reminder: The camera needs to be used with the real-time transmission APP. For the download process, please refer to the APP manual, and for the camera function description, please refer to the APP.
3.PTZ camera control
The whole PTZ camera has a degree of 70 °, and experience a better aerial photography process. As shown in the figure, the roller is in direction A, and the camera is adjusted in direction A; Pull the scroll wheel as shown in the figure to 8 direction and adjust the camera to B direction

Remote Control Part Names

1. Remote control antenna
2. Variable speed/long press the matching knob to adjust the focus
3. Up, down, left turn, right turn
4. Light switch/long press for 3 seconds to turn off obstacle avoidance function
5. One button up/down
6. Mobile phone holder
7. LCD display[8] Indicator light
8. Charging interface
9. GPS Return
10. Left and right side fly forward and backward
11. Image transmission interface
12. Headless mode/long press for 5 seconds to turn off GPS
13. Power switch
14. Pan/tilt adjustment/focus adjustment
15. Take a picture/press and hold to calibrate the gyroscope
16. Video recording/long press to correct geomagnetism

Lcd Display

Remote Control Battery Charging

Tips:

• Insert the plug in the correct way.
• It is recommended to use 5V 1-2A adapter for charging.

Pre-flight Inspection

1. Are the batteries of the remote control and drone sufficient?
2. Whether the blades are installed correctly.
3. Whether the motor starts normally after booting.

Drone Pairing

Turn on the remote control switch, turn on the drone switch, wait for 1-5 minutes, the remote control makes a “beep”, and the frequency is successful.
Geomagnetic Correction Function

After the drone is successfully paired, press and hold the remote control camera button for about 5 seconds (Figure 1), the remote control beeps, the drone light flashes quickly, pick up the drone 1 meter above the ground and turn clockwise 3 circle (picture 2), at this time, after the remote control beeps, put the drone upright, with the camera facing down (picture 3), turn the remote control clockwise three times and make a beep.
Tips: Please make sure that the take-off environment is open, and the satellite signal is greater than 7 stars before take-off.

• Do not perform calibration in areas with strong magnetic fields, such as magnetic deposits, parking lots, construction areas with underground steel bars, etc.
• Do not carry ferromagnetic materials with you during calibration, such as keys and mobile phones.
• Do not calibrate near large pieces of metal.

Drone Gyroscope And Gimbal Level Correction

Place the drone on a level surface, press and hold the remote control for 5 seconds to make a beeping sound, press the button as shown in the figure, and the calibration is successful.
Connect With App

Expand the antenna and handle, connect the adapter cable to the type c interface on the right of the remote control, and install the mobile device. be careful:
The remote control is installed with the adapter of the typec interface by default. Please replace the adapter according to the type of mobile device interface. The connector at the bottom of the remote control is only used for charging the remote control, not for image transmission connection data.
Remote Control Dual Mode
The default Mode2: GPS / optical flow dual mode when booting. When the Mode2 mode is enabled, it needs to be used outdoors in an open place without signal interference such as high-rise buildings and high-voltage wires.
Mode1: Optical flow mode. When using this mode, you need to turn off the GPS function before taking off. [Cannot turn off Mode 2 (GPS mode) after GPS positioning] Mode Switch

1. ATTI MODE indoor mode] is applicable to indoor open places. After the frequency of the UAV and the remote controller are aligned and the geomagnetism and gyroscope are calibrated, POSITIONING is displayed on the display of the remote controller. At this time, the UAV will automatically perform GPS search and positioning, and the automatic activation of the protection program will not be able to take off. You need to press the headless mode key for 5 seconds, and the remote controller will emit a “drip” sound, which means that the takeoff can be unlocked after the GPS function is turned off.
   (Note: ATTI MODE indoor mode does not have a series of GPS functions such as low power return, one-key return, etc. Please pay attention to the flight distance when using it and cannot switch to GPS mode after taking off using ATTI MODE indoor mode. If you need to use GPS mode, you need to land the aircraft and restart it to complete GPS positioning before taking off.

2. GPS MODE: GPS mode] is suitable for outdoor areas without signal interference. After linking the drone and the remote control, calibrating the geomagnetism and gyroscope, the display of the remote control will display POSITIONING, and the drone will automatically perform GPS at this time. Search for satellites and positioning (when searching for satellites, place the drone in an open place, and there should be no obstructions such as tall buildings, cars, high-voltage wires, etc., otherwise the drone may not be able to complete GPS search for satellites and positioning), and wait until the number of satellites reaches 10 When the positioning is completed, the remote control will emit a beep, and the display of the remote control will display GPS MODE, indicating that the positioning is successful, and the takeoff can be unlocked. (Note: In GPS mode, the drone will not be able to take off if the protection program is automatically activated before the GPS positioning is completed)

Normal Mode Smooth Mode Switch Sport Mode Sports Mode
Note: The product is powered on by default in the NORMAL MODE stable mode. The drone has obstacle avoidance functions. If you switch to the SPORT MODE sport high gear mode, the drone obstacle avoidance function will automatically fail. At this time, the drone will not have all obstacle avoidance functions.
Need to pay attention to the flight height and distance, pay attention to the surrounding flying environment, to avoid damage to the drone due to improper flight.

Drone Unlock

At this time, the throttle stick and the directional stick are pushed to the lower left corner and the lower right corner at the same time (Figure 1), or pushed to the lower right corner and the lower left corner (Figure 2) at the same time, the unlocking can be completed and the motor can fly after starting.

Basic flight steps

Basic Flight

1. Code the remote control with the drone, and the drone completes the initialization.
2. Geomagnetic calibration. (Do not need to calibrate each time at the same location)
3. After the drone gyroscope is detected, unlock the drone.
4. Push the throttle stick up, the drone will take off, and the left / right joystick will control the attitude of the drone.
5. Turn off the power of the drone first, and then turn off the power switch of the remote control. Flight Control Method

Flight mode
One-click Takeoff / Landing

• After the drone is unlocked, press the one-button take-off button briefly, and the drone will automatically take off to hover at a height of about 1.5 meters.
• When the drone is in flight, press the one-button take-off button briefly, and the drone will automatically land on the ground.

Headless Mode

Press the headless mode button, the remote controller will make a “dipping” sound. When the drone is unlocked, the direction pointed by the nose is directly in front of the flight. During the flight, rotate the drone in the direction to direct the flight. When the drone is unlocked, the direction the nose points.
Return Home Function
The drone has a home function. If the home point is successfully recorded before takeoff, the communication signal between the remote control and the drone is lost or the home key is pressed, the drone will automatically return to the home point and land to prevent accidents.
There are three different ways for drones to return home:

1. One-click return
2. Signal return
3. Low battery return.

Note for return flight:

• During auto return, the drone cannot avoid obstacles.
• When GPS signal is not good or GPS is not working, you cannot return to home.
• ATTI MODE indoor mode does not have this function

One-click Return
Home Point: When taking off or during flight, when GPS receives 7 or more stars for the first time, it will record the current position of the drone as the home point.

When the GPS signal is good (the number of satellites is greater than 7), you can start the drone home by pressing the one-way home button on the remote control. The home process is the same as the uncontrolled home. Use the stick to control the drone to avoid obstacles. Press the home button again to exit home, and the user can regain control.
Signal Return
The GPS signal is good (the number of GPS satellites is greater than 7), the compass is working normally, and after the drone successfully records the home point, if the remote control signal and the APP signal are off for more than 6 seconds, the flight control system will take over the control of the drone Control the drone to fly back to the signal and stop.
Low Battery Return
After the drone is low-voltage, the indicator light will flash slowly. At this time, the drone will automatically return to the vicinity of the takeoff point 20 meters. (After the low-power drone returns to the vicinity of the take-off point, the height and distance of the drone will be limited to 20 meters)
Reminder: The drone is in the low-power return mode, and the remote control cannot cancel the return mode.
The Influence Of Temperature And Environment On The Use Of Drone Lithium Battery:

1. Temperature has a certain influence on lithium batteries: the best battery temperature is 20~30°C, low temperature environment will reduce the activity of lithium ions, the battery discharge capacity will become weaker, and the use time will be shortened.
2. The impact of the flight environment on the endurance time: When the UAV encounters heavy wind or headwind during the flight, due to the greater resistance, it consumes fast power and shortens the battery life.
   Therefore, when flying outdoors, pay attention to the weather and nearby environment. If the temperature is low, the wind is high or the wind is flying, be careful not to fly far, and return to the home in advance with sufficient battery power to avoid insufficient power in the midway to complete the return.

Photo / Video
Press the ” ” button on the remote control to take a photo, and the remote control LED screen displays Show TAKE PHOTO, Press the ” ” button on the remote control to record, and the remote control LED screen displays Show “VIDEO ON” to start recording, and then press the ” ” button The remote control LED display shows “VIDEO OFF” to stop recording.

Product parts

Basic Parts

Working Principle Of Gps Function And Precautions For Use
After the drone and the remote control are successfully paired, the GPS module on the drone will be connected to the satellite. After the satellite accuracy reaches the positioning standard, the remote control will display MODE 2, which means the GPS positioning is completed, and the drone will remember the take-off point.
When taking off in GPS mode, if the signal is interrupted, there are generally the following two situations:

1. The UAV and the remote control signal off: When the UAV and the remote control signal are interrupted for more than 6 seconds when the UAV is over distance or is interfered by the signal, and the UAV GPS signal is normal, the UAV activates the signal to return to the take-off point.
2. The UAV GPS signal is interrupted: When encountering large obstructions, signal interference, etc., it may directly cause the UAV to fail to receive satellite signals, the UAV GPS signal is interrupted, and the UAV cannot locate and cannot pass the interrupted signal. Return home or return home with one key to return to the point of departure.

Safety Guidelines

In order to avoid accidents, the following safety guidelines should be observed when drones are flying:

| Take off after getting a good GPS signal
---|---
| Keep both hands to control the aircraft throughout
| Check that the accessories and the appearance of the body are in good condition to ensure that the equipment is fully charged
| Fly at a safe altitude, avoiding canyons
| Fly at a safe altitude and avoid buildings with large height differences such as tall buildings
| Avoid places with high signal interference such as signal towers
| Flying in an open area and sight distance For safety reasons, do not fly over people, animals or moving vehicles
| Stay awake and do not fly after drinking alcohol
| Comply with local laws and check relevant laws before flying

Return Flight
A. When the drone starts the return-to-home procedure, the return-to-home method at different altitudes:

1. The height of the drone is less than 20 meters: the drone will first rise vertically to a height of 20 meters from the ground, then return to the vicinity of the take-off point, and then land vertically to the ground.
2. The height of the drone is greater than 20 meters: the drone will return to the vicinity of the take-off point at the altitude, and then land vertically to the ground.

B. Landing differences of different return procedures:

1. One-key return, low power return: If the drone returns to the vicinity of the take-off point, the user can control the drone through the joystick to avoid obstacles.
2. Return to home when the signal is cut off: Because the signal of the drone and the remote controller is disconnected, the remote controller cannot control the drone. The drone returns to the vicinity of the take-off point at a height of 20 meters or more and then falls vertically to the ground.

In summary, users need to pay attention to the following points when using the drone to return home:

1. When using the GPS MODE mode, the drone should be in an open and unobstructed place outdoors, otherwise, once the drone triggers the return-to-home procedure, it will rise vertically and hit an obstacle.
2. The take-off point of the drone should be far away from complex places such as crowds, water, tall buildings, signal towers, trees, etc., and take off in a relatively open place to prevent it from landing directly on obstacles or water when the signal is turned off.
3. Attention: Before using the UAV, it is necessary to know the surrounding environment in advance, including the route environment. The flight altitude of the UAV cannot be too low during flight. The UAV will return to the takeoff point in a straight line after the homing procedure is enabled. Attention should be paid to avoid damage caused by collision with obstacles during the homing process, resulting in the inability to return. (The obstacle avoidance function may fail due to the activation of high gear in the return procedure).

Tip
Because the obstacle avoidance of UAV is realized by visual camera, similar to human eyes, in the dark environment at night, the visual camera can’t see the obstacle, and the obstacle avoidance function will fail. Therefore, it is recommended that novices choose to fly in the day with sufficient light.

Don’t Panic If You Encounter Problems

has a protection program Long press the GPS switch for 5 seconds to turn off the GPS function
2| After the GPS function is turned off in ATTI MODE indoor mode, the drone motor can rotate, but the drone cannot take off. The light flashes quickly and slowly| Recalibrate the geomagnetism after restart
3| After taking off in ATTI MODE indoor mode, the drone keeps flashing and can’t hover, floating around| The ground is too smooth and the environment is too dark, which will cause the optical flow lens to be unstable. Please get a good light and fly in a place where there is no reflection on the ground.
4| After taking off in GPS MODE mode, the drone keeps flashing and can’t hover, and floats around. The remote control keeps switching between ATTI MODE and GPS MODE modes.| GPS positioning is not good, interference is too big, please get open, unobstructed, no high voltage wires
5| The motor of the drone in GPS MODE mode can rotate, the aircraft cannot take off, and the light flashes quickly and slowly| Recalibrate the geomagnetism after restart
6| Drone shakes a lot| The blade is deformed or damaged, it needs to be replaced
7| When the picture is tilted during aerial photography| Land the drone to a flat ground and perform the gimbal level correction again.

Software Installation Instructions

1. Install mobile client
   Please scan the QR code below to download the mobile app from the corresponding website.| |
   ---|---|---
   http://app.hy-chip.com/xl-super_download.html| https://play.google.com/store/apps/details?id=com.hy.xil_fly| https://apps.apple.com/cn/app/xl-super/id1644098718
2. Recommended model configuration

iOS

Model configuration| Recommended configuration| Optimal configuration (2K support)
---|---|---
Product model| IPhone 6 and above| IPhone 6 and above
System version| IOS 11.0 and above| IOS 11.0 and above

Android

CPU model| Recommended configuration| Optimal configuration (2K support)
---|---|---
System version| Xiaolong 630 and above Samsung Exynos 7420 and above
MediaTek Helio X25 and above Kirin 950 and above| Xiaolong 835 and above Samsung Exynos 8895 and above MediaTek Helio X30 and above Kirin 970 and above
Memory size| Android 9.0 and above| Android 11.0 and above
CPU utilization| 3G and above| 6G and above
Model configuration| Occupancy 25% and below| Occupancy 10% and below

Cleaning up background programs can effectively reduce CPU utilization.

Description Of Double-lens Obstacle Avoidance

Effective Use Environment:
The surface is made of diffuse reflection material, with rich surface texture. It can be used in environments with a reflectivity of more than 20% (such as cement pavement) and weak light intensity of more than 5 lux.
Be Careful:
In high gear, visual obstacle avoidance is invalid;
When returning, visual obstacle avoidance is invalid;
In the dark, visual obstacle avoidance is invalid; Because the obstacle avoidance of UAV is realized by visual camera, similar to human eyes, in the dark environment at night, the visual camera can’t see the obstacle, and the obstacle avoidance function will fail. Therefore, it is suggested that novice Xiaobai choose to fly in the day with sufficient light.
When the object in front of the obstacle avoidance lens of the aircraft is a non-textured or repeated texture obstacle, the obstacle avoidance effect is poor, please pay attention to flight safety;
No texture barrier, that is, the surface of the object lacks the diversity of physical properties, resulting in a single image. Including glass mirror, white wall, solid color curtain, large board, etc.
The probability of failure in non-textured environment (pure color area), repeated texture environment and transparent glass is relatively high.
(As shown in the figure below)

Warm Tips (1)

Note: In the fixed-altitude mode (indoor mode), when the aircraft is in the following environment, the optical flow fixed-point hovering effect of the lower lens is not good, which will cause the aircraft to be difficult to fly smoothly, resulting in fuselage jitter.

Warm Tips (2)
If you need to use the remote control, you can connect the remote control correctly according to the prompts.

1. Turn on the remote control;
2. Turn on the remote control;
3. Plug in the remote control adapter and connect the phone.

Be Careful:
The remote control is installed with the adapter of the typec interface by default. Please replace the adapter according to the type of mobile device interface. The connector at the bottom of the remote control is only used for charging the remote control, not for image transmission connection data.

Camera Parameters

Support memory card types| The MicroSD card supports a maximum of 128GB, and the write speed level is above class 10/U1/V10.
---|---
Save phone without card|
---|---
photograph| 3840•2160P
video frequency| 19209080P
SD card after card Insertion|
photograph| 3840’2160P
video frequency| 3840’2160P
Mobile phone after card insertion|
photograph| 3840’2160P
video frequency| 19209080P
Download SD card in APP to mobile phone|
photograph| 3840’2160P
video frequency| 3840’2160P
Maximum code stream of main camera video| 40Mbps

Control Interface – Home Page

Control Interface – Control Page![Tucok 012S Adults 4K Drones with Camera

• Control Page 1](https://manuals.plus/wp-content/uploads/2024/03/Tucok-012S- Adults-4K-Drones-with-Camera-Control-Page-1.png) Control Page – Function Description (I)

WiFi: Display the signal strength of image transmission;
Number of satellites: Indicates the current flight mode and the number of satellites; Red indicates fixed altitude mode, without return, follow, surround and guidance flight functions. Constant light indicates that it is in GPS mode.
Power: Aircraft power status.

1. The 2-4 grid indicates the normal power, and the homing, following, circling and pointing flight functions can be operated normally in GPS mode.
2. 1 bar (flashing state) indicates that the aircraft is currently in low battery state and will perform automatic homing function; There are no following, circling and guiding flight functions in low battery state.

GPS information: Display the altitude and distance from the current aircraft to the return point, A-altitude D-distance H-horizontal speed V-vertical speed.
Control Page – Function Description (Ii)

*Extension description – shooting mode
Spiral: After the start, the aircraft will automatically spiral, pay attention to the obstacles above to avoid injury! In case of emergency, immediately use the remote control to interrupt the flight!
Soaring: After starting, the aircraft will rise automatically. Pay attention to the obstacles above to avoid injury! In case of emergency, immediately use the remote control to interrupt the flight!
Faraway: After the start, the aircraft will lean back away from the target, pay attention to the space behind, and avoid causing damage! In case of emergency, immediately use the remote control to interrupt the flight!
AR： Embed AR 3D model in real-time video stream;
50x zoom: After opening, you can adjust the zoom factor of the lens view by adjusting the left slider. After the view is enlarged, slide your finger on the screen to move the viewing range of the view.
GPS follow: In GPS mode, click this button and the aircraft will follow the mobile phone.
No UI mode : Hide unnecessary UI controls;
Orbit flight : In GPS mode, the aircraft nose will orbit clockwise or counterclockwise with the current position of the aircraft as the center of the circle.
During the encircling process, it can be controlled to rise, fall, and adjust.
VR: Click to enter VR mode.
Waypoint flight* : In GPS mode, the aircraft will fly according to the selected position on the map.
PTZ: Open the front lens PTZ controller.
Vertical screen mode: Turn on portrait mode.
Extension description – shooting mode**
Click [More] on the control page, click the vertical screen to directly open the vertical screen shooting, or click [Settings] – Image transmission settings – shooting mode to open the delayed shooting and vertical screen shooting.

Control Page – Function Description (Iii)

Multi-lens Function Description

cut from one shot to another
Lens switching and multi-lens window:
In the expanded button, you can freely switch the up and down shots and binocular ranging of the UAV; And combine mobile camera to realize free combination of multiple windows.
Click the [Switch Lens] button to switch the following four functional states in sequence:

1. Ordinary front lens;
2. Lower lens;
3. Binocular ranging;
   When the [Switch lens] button is not clicked, the default is the normal front lens function.

Rocker And Pan Head

Front lens PTZ controller
After the aircraft takes off, the front lens PTZ controller will be displayed on the right side of the screen. At this point, if you move the slider of the controller upward, the front lens of the aircraft will move upward by a certain angle; If you move the slider downward, the front lens of the aircraft will move downward by a certain angle.
share
Click the button at the bottom right of the screen on the control page to enter the album interface. When clicking to view photos or videos, users can share photos or videos to major social platforms through the button in the upper right corner.

gesture Recognition

Facing the camera front lens, the following gestures can trigger the automatic photographing or shooting function of the aircraft:
Yeah, take pictures with gestures
At about 2m in front of the aircraft lens, raise one hand flat to make the “Yes” gesture; After the aircraft successfully recognizes the gesture, the countdown is 3 seconds and the camera starts to take pictures.
Palm gesture video
Close the five fingers and lift flat with one hand about 2m in front of the aircraft lens; After the aircraft successfully recognizes the gesture, the video recording will begin. When recognizing the gesture again, end the recording (the time difference between the two recognition should be greater than 3 seconds).
*Warm tips
To ensure high recognition rate of the lens——

1. Please aim at the camera;
2. Please fly in a light environment;
3. Please conduct gesture recognition at a position about 2m away from the camera.
4. Ask the user to face the camera; (Face auxiliary features)

Under the following circumstances, the lens recognition rate will be reduced——

1. Weak light or backlight environment;
2. WiFi signal is weak, or the signal is disturbed.

MV Interface

Click the button on the right side of the screen on the control page to enter the MV interface. In the MV interface, you can shoot music videos.

Rotating picture
Click this button to enable the rotation screen function. At this time, the finger slides on the screen to rotate the image;
If you double-click the value at any position of the screen with your finger, you can instantly enlarge the image (this function is also applicable when recording video).

Select Music

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>