ICON KDBC18 Touch Series Height Adjustable Standing Desk Instructions

ICON KDBC18 Touch Series Height Adjustable Standing Desk

Product Information

• Specifications:
  • Product Name: KDBC18 Integrated Handset
  • Series: TOUCH SERIES
  • Ports: Motor Port 1, Motor Port 2, USB port, Power Port Expansion

Product Usage Instructions

• Handset Normal Operation Manual:
  • Initialization Steps:
  • Press and hold the Down button and Up button simultaneously for more than 3 seconds.
  • Keep pressing both buttons until the legs move down to the lowest position, rebound -25 mm, and then stop.
  • Release both buttons. Initialization is completed.
  • Note: The initialization procedure must be completed before the first run after installation or parts replacement. Any interruption in initialization will require re-initialization.
• Move Up and Down:
  • Press and hold the Up button to move the legs up.
  • Release the Up button to stop leg movement.
  • Press and hold the Down button to move the legs down.
  • Release the Down button to stop leg movement.
• Set Memory Positions 1/2/3:
  • Press and hold the desired memory button and run the legs to the desired height, then release.
  • Click button S, then click Position 1 2 or 3 within the next 3 seconds to save the position.

FAQs

• Q: What should I do if the system stops during initialization?
  • A: If the system stops during initialization, you will need to re-initialize the system before proceeding with operation.
• Q: Can memory positions be overwritten?
  • A: Yes, memory positions can be overwritten by following the memory position setting instructions.

Product Functions

• A. Definitions of all the functions
• B. Handset normal operation manual：

Installation Step

1. Initialization steps：
2. The initialization procedure must be completed before first running after the table is installed or parts replaced.
3. Any interruption in initialization will cause the system to stop and request re-initialization.
4. Move up and down
5. Set memory positions 1/2/3
6. Memory position will be erased after initialization；
7. Memory position can be overwritten.
8. Move to the memorized positions 1/2/3：****
   Step| Operation| Motion
   ---|---|---
   1| Press and hold the buttons 1 or 2 or 3| Return to the corresponding position saved
9. Set up stroke limit of rising and lowering
10. Lock up the rising stroke****
    3| Release the key| Setting complete
    ---|---|---
11. The column cannot run higher than the locking height.
12. Setting the highest stoke limit will erase the memory positions higher than the locking height, and even if the stroke unlocking operation is performed, the memory positions higher than the locking height cannot be recovered. You must reset the memory position according to the setting instructions for memory position.
13. The locking height will not be unlocked after initialization.
14. Lock up the lowering stroke****
    Step| Operation| Motion
    ---|---|---
    1| Press  [8     or [8, then release the key| Run the column to your desired height
    2| Hold key S, and then hold key 1, lasting more than 3 seconds| The caption “L” is displayed on the screen, indicating that the current height is locked as the lowest running height
    3| Release the key| Setting complete
15. The column cannot run lower than the locking height.
16. Setting the lowest stoke limit will erase the memory positions lower than the locking height, and even if the stroke unlocking operation is performed, the memory positions lower than the locking height cannot be recovered. You must reset the memory position according to the setting instructions for memory position.
17. After initialization, the lowest locking height is unlocked.
18. Unlock stoke Limit****
    Step| Operation| Motion
    ---|---|---
    1| Press and hold keys， then press and hold key 2 over

2 minutes

| The caption “-c-” is displayed on the screen, indicating that the stroke limits are both unlocked
2| Release the key| Complete
7. Exchange of Imperial system and Metric system.****
Step| Operation| Motion
---|---|---
1| Hold Key S then hold key [8   for 3 seconds| Display height switches between centimetres and inches
2| Release the key| Switch done
---|---|---

1. As the column rises or falls, in the imperial display format, the minimum change in height is 0.5 inches, while in the metric display format, the minimum change in height is 1 cm
2. Correct display height to office table height****
   Step| Operation| Motion
   ---|---|---
   1| Set the table at any height, recommended at

the bottom position

| Measure the table’s actual height and write down the number in inches or centimeters
2| Hold key S and hold[8

over 3 seconds

| The first digit flashing on the screen
3| Release key， and then

click[8 or[8 to adjust the first digit

| Increase or decrease the first digit on the screen to your measured number
4| Click key S| The second digit flashing on the screen
5| Click[8 or[8 to adjust the

second digit

| Increase or decrease the second digit on the screen to your

measured number

6| Click key S| The third digit flashing on the screen
7| Click [8 or[8 to adjust the

third digit

| Increase or decrease the third digit on the screen to your

measured number

8| Click key S| Setting complete

1. Check whether the handset display format matches the measured data, either in centimetres or inches. In imperial display format, the minimum height adjustable unit is 0.5 inch, and in metric display format, the minimum height adjustable unit is 1 cm.
2. Error code****
   Error

Code

| Cause for

Error

| Criteria for

Determination

| Troubleshooting Solutions
---|---|---|---
E01| Column malfunction| The linkage between the columns and the control box is disconnected, displaying E01| 1.  Check to see if the link cable between the columns and the control box is disconnected.

2.    Check to see if there is any part damaged in the columns. Replace the column if yes.

E03| Overload| Desktop load exceeds the control| 1. The column is overloaded. Reduce the load.
| | box rated loading

limit, displaying E03

|
---|---|---|---
E04| Abnormal data| Control box abnormal data, displaying E04| 1.  Operate the system in a harsh environment, which results in abnormal control box data and requires initialization.

2.  The initialization process is interrupted, resulting in abnormal control box data, which requires re-initialization.

E05| Key stuck| Handset value is detected unchanged for more than 30 sec under pressing, displaying E05.| 1. Reposition the key on the handset if it gets stuck. 2. Replace the handset.
E11| Abnormal power and voltage| Abnormal voltage supply| 1. The power connection to the control box is loose. Check whether the power connection is secure
2. The external power supply does not work properly. Replace the power supply

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>