EcoSmart LR1321-RGB-TV-3.8M-1024 RGB TV Backlight with Color Sensing User Guide

EcoSmart LR1321-RGB-TV-3.8M-1024 RGB TV Backlight with Color Sensing

Safety Information

PRECAUTIONS

Read and understand this entire manual before you attempt to install or operate this product.

• This strip light is intended for indoor use only.
• This strip light is not intended for commercial use.
• Do not expose the strip light to excessive heat or moisture.

CAUTION : Do not use rough textured cleaning tools or highly corrosive cleaners when cleaning your LED Lights. These tools and chemicals will damage the product. ONLY use a soft damp cloth and non corrosive cleaners.

CAUTION : Do not scratch the LED strips or use sharp objects on them.

CAUTION : Do not permanently bend, twist, or screw through the LED strips as this will damage the LED’s internal components.

CAUTION : Do Not pull or snap with excessive force, this will damage the product.

CAUTION : If the product is damaged or wires are frayed or damaged, do not use the product. If your product arrived in this condition, contact us for a replacement.

CAUTION : Only use fuses of the same type and characteristics. Short circuiting the fuse holders is prohibited.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
could void the user’s authority to operate the equipment. Responsible Party-U.S. Contact Information

Elecwish Inc/Add: 4225 Etiwandaavenue, Suite 1 mira loma, California 91752, USA/ Elecwish.com

Please keep observed safety notes before use:

Class 2 POWER SUPPLY
Model: S024D2401000U
Input: 100-240V~, 50/60 Hz, Max.600mA
Output: 24Vdc, 1000mA

“IMPORTANT SAFETY INSTRUCTIONS–SAVE THESE INSTRUCTIONS” AND “DANGER-TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS”

To comply with the published safety standards, the following must be considered when using this power supply.

1. For connection to a supply not in the U.S.A, use an attachment plug adapter of the proper configuration for the power outlet, if needed.
2. Please read the instructions Before using the power supply
3. This unit is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack if experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure thy do not play with the unit.
4. For indoor use only.
5. Please Don’t use the charger in the damp environment and High temperature.
6. Don’t operate unit with damaged plug.
7. Don’t disassemble power supply. Disassembly may result in a risk of electric shock or re.
8. To reduce the risk of electric shock, unplug the charger from the outlet when not in use.
9. Don’t operate unit if it has been subjected to damage in any way.

Warranty

2-YEARS LIMITED WARRANTY

The manufacturer warrants this lighting Fixture against defects in materials and workmanship for a period of two years from the date of purchase. If within this period the product is found to be defective in material or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price to the original purchaser or consumer. This warranty does not cover light bulbs or the Fixture becoming damaged due to misuse, accidental damage, improper handling and/or installation, and specifically excludes liability for direct, incidental, or consequential damages. As some states do not allow exclusions or limitation on an implied warranty, so the above exclusions and limitations may not apply. This warranty gives you specific rights and you may also have other rights that vary from state to state.
Contact the Customer Service Team at 1-800-910-7164 or visit www.HomeDepot.com/EcoSmart.

Pre-Installation

PACKAGE CONTENTS

Installation

Preparation Before Installing

• Unbox the strip lights and check all items listed in the packing list.
• Power on the strip lights and check whether they light up

Installation Steps:

• Wipe the installation surface to ensure it is dry and clean.
  

• Stick the strip light to the back of the TV. Press them rmly and then reinforce them with the provided clips.
  
  

• Position the sensor to the top center of the TV.
  

• Insert the cable of the power supply and the sensor into the controller.
  

• Power on and start your colorful TV life.
  55in TV
  
  65in TV
  

NOTE : Do not plug the power supply in before all the steps are ready in case the TV sensor doesn’t work.

Operation

Remote Operation

CAUTION : The remote control included utilizes a 3V CR2025 battery; Do not dispose of batteries in fire as they may explode or leak. Please dispose of used batteries immediately and safely. Only replace with the same battery type. Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if compartment is not secure.

WARNING : KEEP BATTERIES OUT OF THE REACH OF CHILDREN! BATTERIES ARE NOT A TOY! If swallowed, they can cause severe injury or death within 2 hours. In case of swallowing, call emergency services immediately. Tell others of the risks associated with button batteries to keep kids safe.

• Remove the plastic tab from the back of the handheld remote (E).
• Ensure the battery contacts are clean prior to battery installation.
• Remove batteries from equipment when not in use for an extended period to time.
• Aim the remote directly at the controller.
  

| Button| Description
---|---|---
1| | ON: Press to turn on the light
2| | OFF: Press to turn off the light
3| | Adjustable brightness: Increase or decrease the 10-level of light brightness
4|

| Dynamic mode toggle:

• 3 jumping color (red, green, blue)
• 3 fading color (red, green, blue)
• 7 jumping color (red, yellow, green, cyan, blue, purple, white)
• 7 fading color (red, yellow, green, cyan, blue, purple, white)
• Multi-color jumping and fading mode(red, green, yellow, cyan, blue, purple, white in random sequences)

5| | Adjustable speed: Increase or decrease the 10-level speed of dynamic mode
6| | Static (solid) color:
Red, green, blue, white, orange, yellow, sky blue, purple, cyan, pink
7| | TV: TV color sensing mode
8| | Music 1: Music sync mode – slow Color jumping function with gentle rhythm (random color from all static colors above) Music 2: Music sync mode – fast Color jumping function with rough rhythm (random color from all static colors above)
9| | Auto:Multi-color jumping and fading mode(red, green, yellow, cyan, blue, purple, white in random sequences)

Controller Operation

Care And Cleaning

• Before attempting to clean the light strip, unplug the adaptor from the power outlet.
• To clean the light strip, use a clean, dry, or slightly damp cloth.
• Allow the light strip and components to dry thoroughly before plugging the power adaptor back into the outlet.
• Do not use any cleaners with chemicals, solvents, or harsh abrasives, as damage to the strip light may occur

Troubleshooting

• Check all wire connection. Unplug and replug the power adapter to ensure the controller power on correctly.

The provided adhesives don’t stick well.|

• Wipe the installation surface to ensure it is dry and clean.
• When attaching the strip lights, ensure you press down firmly.
• Reinforce the strip lights with the provided clips or other strong adhesives.

Customer Support

Questions, problems, missing parts? Before returning to the store,
call EcoSmart Customer Service
8 a.m.-7 p.m., EST, Monday-Friday, 9 a.m.-6p.m., EST, Saturday
1-800-910-7164
HOMEDEPOT.COM/ECOSMART
Retain this manual for future use.

References

• Elecwish - Shop Quality Home Furniture at Affordable Price
• EcoSmart - Light Bulbs - Lighting - The Home Depot
• EcoSmart - Light Bulbs - Lighting - The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>