KMC CONTROLS MEP-7000 Series Actuators Crank Arm Kit Installation Guide

May 15, 2024
KMC CONTROLS

KMC CONTROLS MEP-7000 Series Actuators Crank Arm Kit

Specifications

  • Product: Crank Arm Kit for MEP-7000 Series Actuators
  • Model: HLO-1020

Product Usage Instructions

Mounting

  1. From the MEP-7xxx actuator, remove and discard the V-bolt.
  2. Assemble and install the kit and actuator as shown in the diagram below.

NOTE: Position both the ball joints as close to the end of the crank arms as feasible for the application. Placing a ball joint in the slot nearer to the shaft will alter torque, rotation speed, and/or angle of rotation.

NOTE: Check for potential issues such as binding of the linkage or damage caused by the actuator still rotating when the damper is closed.

Maintenance

Under normal conditions, no routine maintenance is required. In harsh environments, periodic lubrication of the ball joints may be necessary for long-term reliability and performance. Careful installation is key to ensuring product longevity.

More Information

For additional installation details, refer to the
MEP-7200/7500/7800 Series Installation Guide on the KMC website.

Important Notices

The KMC logo and KMC Controls are registered trademarks of KMC Controls, Inc. All rights reserved.

No part of this publication may be reproduced without written permission.

The material in this document is for information purposes only and is subject to change without notice.

FAQ

Q: Is routine maintenance necessary for the crank arm kit?

A: Under normal conditions, routine maintenance is not required. However, in harsh environments, periodic lubrication of the ball joints may be necessary for long-term reliability.

Q: Where can I find additional installation information for MEP-7xxx actuators?

A: Additional installation details can be found in the MEP-7200/7500/7800 Series Installation Guide on the KMC website.

Q: What should I do if I encounter issues during installation?

A: If you encounter issues such as binding of the linkage or damage during installation, refer to the provided installation guide for troubleshooting steps. You can also contact KMC Controls for assistance.

Crank Arm Kit for MEP-7000 Series Actuators

HLO-1020

Mounting

  1. From the MEP-7xxx actuator, remove and discard the V-bolt.
  2. Assemble and install the kit and actuator as shown in the diagram below.
    • NOTE: In general, position both the ball joints as close to the end of the crank arms as is feasible for the application. Positioning a ball joint in the slot closer to the shaft will change the torque, rotation speed, and/or angle of rotation—which may be useful for some applications.
    • NOTE: Check for potential issues such as binding of the linkage or damage caused by the actuator still rotating when the damper (or other application) is already closed.
    • NOTE: For additional information about installing MEP-7xxx actuators, see the MEP-7200/7500/7800 Series Installation Guide on the KMC web site (www.kmccontrols.com).

Maintenance

Under normal conditions, no routine maintenance is required. In harsh environments, however, periodic lubrication of the ball joints may be necessary.
Each component is designed for dependable, long-term reliability and performance. Careful installation will also help ensure long-term reliability and performance.

Kit Contents

  • 1 crank arm
  • 2 ball joints for 3/8″-diameter rod (rod not included)
  • 2 mounting brackets
  • Mounting screws

KMC-CONTROLS-MEP-7000-Series-Actuators-Crank-Arm-Kit-
fig-1

More Information

For additional information about installing MEP-7xxx actuators, see the MEP-7200/7500/7800 Series Installation Guide on the KMC web site (www.kmc- controls.com).

Important Notices

  • The KMC logo and KMC Controls are registered trademarks of KMC Controls, Inc.
  • All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permis-sion of KMC Controls, Inc.
  • The material in this document is for information purposes only. The contents and the product it describes are subject to change without notice. KMC Controls, Inc. makes no representations or warranties with respect to this document. In no event shall KMC
  • Controls, Inc. be liable for any damages, direct or incidental, arising out of or related to the use of this document.

KMC Controls, Inc. 19476 Industrial Drive New Paris, IN 46553 574.831.5250
www.kmccontrols.com
info@kmccontrols.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

KMC CONTROLS User Manuals

Related Manuals