FROG Pool Tender 01-13-4412 Mineral Pool Care Cycler

Customer Service 800-222-0169 frogproducts.com

WARNING
To minimize the risk of serious injury, death or damage, before installing or first using this equipment, read Instruction Manual and all safety labels and follow all safety instructions and precautions. Save manual for future reference.
Welcome to easier pool care courtesy of FROG®. With FROG Pool Tender, your pool water will look and feel better without a lot of work or a lot of chlorine. This system† controls bacteria using a combination of minerals and reduced chlorine levels–up to 50%* less.

There are 4 parts to the FROG Pool Tender System:

1. FROG Pool Tender Cycler
2. FROG Pool Tender Mineral Chamber
3. FROG Pool Tender Algaecide
4. FROG Pool Tender Chlorine Chamber

Part 1
FROG Pool Tender Cycler
The water treatment center that controls the flow of water to each part of the FROG Pool Tender System.

Part 2
FROG Pool Tender Mineral Chamber
Holds the minerals and fits inside the FROG Pool Tender Cycler. Part No. 01-13-4412

Part 3
FROG Pool Tender Algaecide
Use with the FROG Pool Tender Cycler for a 90-Day Algae-Protection Guarantee. One bottle is good for 15,000 gallons. Part No. 01-11-4060

Notes and Safety Information

Part 4
FROG Pool Tender Chlorine Chamber
Prefilled with chlorine tablets and fits inside the FROG Pool Tender Mineral Chamber.
Part No. 01-04-4440

FROG Pool Tender Mineral Chamber comes inside FROG Pool Tender Cycler and is also sold separately. FROG Pool Tender Chlorine Chamber and FROG Pool Tender Algaecide also sold separately. †FROG Pool Tender Mineral System consists of the FROG minerals silver chloride and carbonate used in conjunction with 0.5 ppm chlorine. The FROG Pool Tender Mineral Chamber must be used in conjunction with the FROG Pool Tender Chlorine Chamber, an EPA registered chlorine pool product or a chlorine delivery device.

• Compared to the minimum EPA recommended chlorine level of 1.0 ppm for a stabilized swimming pool.
• For pools and hot tubs.

Notes and Safety Information

General Notes
These instructions contain information for the safe and proper operation of this Cycler.

Observe the following principles:

• Ensure that everyone using this Cycler follows the instructions and safety precautions.
• Keep the instructions nearby and available for reference throughout the service life of this Cycler.

These instructions do not provide for every possible contingency that might be encountered in connection with installation, opera-tion or maintenance of this equipment. Should further informa-tion be desired or should particular issues arise which are not covered sufficiently in this manual, contact King Technology at 800-222-0169.

Explanation of the signal words
Signal words, which depict the probability and severity of harm, are used in these instructions. They are defined as follows:

avoided, will result in death, serious injury or major property damage.
WARNING| Indicates a hazardous situation which, if not avoided, could result in serious injury, death, or major property damage.
NOTICE| Indicates special instructions that are important but not related to physical injury hazards.

Explanation of the safety pictographs
The following pictographs illustrate the type of hazard.

Identification of warnings
Warnings are intended to help you recognize risks and avoid death, injury or property damage. This is how warnings are identified:

Signal Word
Pictographs
Description of danger. Consequences if ignored.
⇒The arrow signals a safety precaution to be taken to eliminate or reduce the risk.

Safety Label on Cycler
Review this label before installing or operating this Cycler. Contact King Technology at 800-222-0169 if this label is missing from your FROG Pool Tender Cycler.

Fire, explosion and high pressure hazards
To minimize the risk of serious injury, death or property damage while using the FROG Pool Tender Cycler:
Read, understand and follow all instructions and safety precautions in the manual, and on this Cycler and on any label for chemicals used with this Cycler including FROG Pool Tender Chlorine Chambers, FROG Pool Tender Mineral Chamber and FROG Pool Tender Algaecide.

DANGER

• Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.

• Never mix Trichlor chlorine tablets with Calcium Hypochlorite, or with any other form of concentrated chlorine or other chemicals.

• Never add any other types of chlorine or shock treatments through the skimmer. These products should be added directly into the pool
  if required.

• Do not contaminate the FROG Pool Tender Cycler, FROG Pool Tender Mineral Chamber, FROG Pool Tender Chlorine Chamber or FROG Pool Tender Algaecide with dirt, organic matter, pool chemicals (such as calcium hypochlorite or pool shocks), fertilizers or other household chemicals. Contact between any of these substances and the FROG Pool Tender Cycler, FROG Pool Tender Mineral Chamber, FROG Pool Tender Chlorine Chamber or FROG Pool Tender Algaecide, will result in a chemical reaction with the generation of heat, liberation of hazardous gasses and fire or explosion.

WARNING

• Use only FROG Pool Tender Chlorine Chambers, FROG Pool Tender Mineral Chamber, and FROG Pool Tender Algaecide in the FROG Pool Tender Cycler. Never use bulk chemicals.
• To prevent the build up of gas pressure in the FROG Pool Tender Cycler, be sure the pool return line valves are open – except when opening or servicing the unit.
• Do not inhale fumes from the FROG Pool Tender Cycler or FROG Pool Tender Chlorine Chamber.
• Avoid sparks, smoking, or any open flame near FROG Pool Tender Cycler or chemicals.
• Do not exceed maximum operating pressure of 50 psi or maximum temperature of 104º F.
• Do not remove the cap while under pressure. Always turn off pump and bleed off pressure before opening FROG Pool Tender Cycler.
• Do not install automatic or fast shut off valves downstream of Cycler.
• Always install the FROG Pool Tender Cycler AFTER a heater (if applicable) on the return line.
• Always install any additional sanitizing equipment AFTER and NEVER BEFORE the FROG Pool Tender Cycler is installed on the return line.
• Do not permit children to use or climb on this product. This product must be positioned to prevent children from using it as a means of access to the pool.
• Always stand clear of the FROG Pool Tender Cycler during pump start-up.
• Replace FROG Pool Tender Cycler if you see signs of cracks, damage or degradation to the Cycler body or cap.

NOTICE

• Prior to pressurizing, check with your dealer to ensure your plumbing connections meet building codes.
• Failure to properly winterize your FROG Pool Tender Cycler could result in freeze damage. (See page 18 for winterizing details.)

Installation Tips to Ensure Proper Performance

Before installing, read all directions carefully and contact your dealer for installation support.

WARNING

• Do not exceed maximum operating pressure of 50 psi.
• Do not install automatic or fast shut off valves downstream of FROG Pool Tender Cycler.
• Always install the FROG Pool Tender Cycler AFTER the heater (if applicable) on the return line.
• Always install any additional sanitizing equipment AFTER and NEVER BEFORE the FROG Pool Tender Cycler is installed on the return line.

If using a multi-speed pump, run pump for at least 6 hours per day at high speed (at least 40 gpm).
If the pump will run on low speed 24 hours per day or less than 6 hours per day on high speed, you must bleed the air while the pump is on by unscrewing the back knob until water appears. Then screw the knob back in. Repeat this process each time the cap is removed for any reason. Install Cycler with 4-8 psi back pressure.
Lower back pressures could result in under chlorination. Change the eyeball fittings in the return jets to a smaller size to increase back pressure. Contact King Technology at 800-222-0169 for a specially designed Cycler pressure gauge to determine back pressure at pool start-up.

Special installation Requirements:
IMPORTANT: Over chlorination or damage to the FROG Pool Tender Cycler or other equipment could result if special installations A, B or C are not used in these situations.

• If water flow is higher than 80 gallons per minute (gpm), see diagram A.
• If an in-floor cleaner is included with pool, see diagram B, with two options. Preferred installation is Option 1 with two separate lines.
• If set-up is a pool and spa combination with common equipment, see diagram C.

Questions? Call Customer Service at 800-222-0169 Monday thru Friday, 8 am to 5 pm central time.

B. With In-Floor Cleaner – TWO OPTIONS
OPTION 1- A Two-Line Installation
The best option is to have two lines. One line with pump, filter, heater and FROG Pool Tender Cycler and a second line with a separate pump for the in- floor cleaning system (filter optional).

OPTION 2 – A 3-Way Valve Installation

OPTION 2 – A 3-Way Valve Installation

TOOLS NEEDED

INCLUDED WITH FROG Pool Tender Cycler

MATERIALS NEEDED

RECOMMENDED
4-8 psi Back Pressure
To avoid over or under chlorination, replace eyeball fittings in the return jets to a smaller or larger size to adjust back pressure. For best results use King Technology’s pressure gauge, order Part No. 01-22-4000.

Sand Filter Installation with Nipple Kit and Flex Hose

1. Apply pipe thread tape or sealant to each threaded end of nipple.
2. Screw one end of nipple into the filter return. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN.
3. Screw either side of FROG Pool Tender Cycler on to open nipple end until upright and secure.
4. Apply pipe thread tape or sealant to threaded end of hose adapter.
5. Screw adapter into the other side of FROG Pool Tender Cycler. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN.
6. Attach return section of hose to the adapter with clamp. Tighten clamp with screwdriver.
7. To prevent damage to heaters or filters, see your dealer about installing a corrosion resistant check valve which will reduce the back flow of chlorine gas when the FROG Pool Tender Cycler is turned off.

TOOLS NEEDED

MATERIALS NEEDED

RECOMMENDED
4-8 psi Back Pressure
To avoid over or under chlorination, replace eyeball fittings in the return jets to a smaller or larger size to adjust back pressure. For best results use King Technology’s pressure gauge, order Part No. 01-22-4000.

Sand Filter Installation with Flex Hose Only

The FROG Pool Tender Cycler should always be installed between the filter and pool (or between heater and pool if applicable). Never install FROG Pool Tender Cycler before the heater or damage to the heater could occur.

1. Apply pipe thread tape or sealant to the threaded end of both hose adapters.
2. Screw adapters into each end of FROG Pool Tender Cycler. Hand tighten. Finish tightening by turning 1 to 2 revolutions with pipe wrench. DO NOT OVER TIGHTEN.
3. Attach the filter section of flex hose to one hose adapter and the return section of flex hose to the other hose adapter with clamps and tighten with screwdriver. Bi-flow valve design allows water flow installation in either direction.
4. To prevent damage to heaters or filters, install a corrosion resistant check valve which will reduce the back flow of chlorine gas when the system is turned off.
5. For better stability, FROG Pool Tender Cycler may be mounted on a treated wood base using Phillips pan head screws, one in front and two in back. If you have questions about stability, please contact your dealer or King Technology.

TOOLS NEEDED

INCLUDED WITH FROG Pool Tender Cycler

MATERIALS NEEDED

RECOMMENDED
4-8 psi Back Pressure
To avoid over or under chlorination, replace eyeball fittings in the return jets to a smaller or larger size to adjust back pressure. For best results use King Technology’s pressure gauge, order Part No. 01-22-4000.

DE and Cartridge Filter Installation

1. Apply pipe thread tape or sealant to each threaded end of nipple.
2. Screw one end of nipple into the filter return. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN .
3. Screw either side of FROG Pool Tender Cycler on to open nipple end until upright and secure.
4. Apply pipe thread tape or sealant to threaded end of hose adapter.
5. Screw either side of FROG Pool Tender Cycler on to open nipple end until upright and secure.Screw adapter into the other side of FROG Pool Tender Cycler. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench. DO NOT OVER TIGHTEN.
6. Attach return section of hose to the adapter with clamp. Tighten clamp with screwdriver.
7. For better stability, FROG Pool Tender Cycler may be mounted on a treated wood base using Phillips pan head screws, one in front and two in back. If you have questions about stability, please contact your dealer or King Technology.

TOOLS NEEDED

MATERIALS NEEDED

SECURE CYCLER

For better stability, FROG Pool Tender Cycler may be mounted on a treated wood base using Phillips pan head screws, one in front and two in back. If you have questions about stability, please contact your dealer or King Technology.

Hard-Plumbed Installation

The FROG Pool Tender Cycler should always be installed between the filter and pool (or between heater and pool if applicable). Never install FROG Pool Tender Cycler before the heater or damage to the heater could occur.

Do NOT install in copper pipe if using FROG Pool Tender Chlorine Chamber as chemical corrosion may lead to pipe failure.

1. Screw adapters into each end of FROG Pool Tender Cycler following directions for a male adapter or a female adapter. Hand tighten. Finish tightening by turning 1 to 2 revolutions with a pipe wrench.
   DO NOT OVER TIGHTEN.

   • If using male adapters, apply pipe thread tape or sealant to the threaded end of each adapter.
   • If using female adapters, apply pipe thread tape or sealant to the threaded end of each cycler port.

2. Measure the distance between the outside adapters and cut out a section of pipe 3” less than that dimension.

3. Following Primer directions, brush Primer on the inside of the adapters and to ends of pipe. Repeat this process with PVC cement following manufacturer’s directions on that product.

4. Insert PVC pipe into adapters with a twisting action. Hold in place 5 to 10 seconds to bond.

5. To prevent damage to heaters or filters, see your dealer about installing a corrosion resistant check valve which will reduce the back flow of chlorine gas when the Cycler is turned off.

Step 1: Preparing the Pool

1. Make sure the pool has adequate circulation. The total volume of pool water must completely circulate through the pump and filter at least 1 to 2 times per day. This usually requires 8 to 12 hours of circulation. Check with your dealer for the proper circulation time for your pool.

2. Check the pool’s filter gauge often and periodically clean filter per the manufacturer’s directions. A dirty filter will slow the flow of water which could hamper proper circulation.
   WARNING
   Do not exceed maximum operating pressure of 50 psi.

3. Check the Water Hardness of your fill water before adding to the pool. If calcium content is higher than 400 ppm, find a soft water source to fill your pool instead; otherwise water balance will be very difficult.

4. Check for metals in the pool such as iron or copper. Before attempting water balance, these should be removed. See your dealer for a metal out or sequesterant and follow the label directions carefully.

5. Before beginning with any pool care program, you must first balance your pool water. Take a water sample to your local pool professional (or use a complete test kit) to test for the important Water Balance Guidelines.
   IMPORTANT: Always follow printed instructions on the balancing chemical packages. Add balancing chemicals in small increments one at a time with circulation running. For best results, wait 8-12 hours before testing again and adding any additional balancing chemicals.
   Water Balance Guidelines
   pH: 7.2 – 7.8
   Total Alkalinity: 80 – 120 ppm
   Hardness: 200 – 400
   Total Dissolved Solids: <1500
   Stabilizer: 20 – 80 ppm
   Free Chlorine: 0.5 – 1.0 ppm
   For best results in achieving water balance, follow steps 5a through 5e in order.

   • 5a. Take a water sample from the pool and dip a FROG Test Strip into it.
   • 5b. Look at the Total Alkalinity reading first. Adjustments should be made to bring the Total Alkalinity in the range of 80 – 120 ppm prior to making any adjustments to pH even if it throws pH off further.
   • 5c. After Total Alkalinity is in range, test for pH. It should be between 7.2 and 7.8. If higher or lower, add a pH adjuster.
   • 5d. Then test your Water Hardness again. If lower than 200 ppm, add Calcium Increaser. Always maintain 200-400 ppm.
   • 5e. Lastly test for stabilizer or conditioner levels. Add conditioner if the level is below 20 ppm. This will prevent chlorine burn off. If stabilizer level is above 80 ppm, partially drain water and re-fill.

6. Initially shock the pool with a chlorine shock only to rid the water of contaminants and establish a chlorine residual. Always follow the manufacturer’s directions carefully. See the DANGER box below for important guidance on shocking.
   DANGER

   • Never add any other types of chlorine or shock treatments through the skimmer. These products should be added directly into the pool if required.
   • Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.

Step 2: Putting the System to Work

1. Install a FROG Pool Tender Mineral Chamber into the FROG Pool Tender Cycler. (See page 15 for directions.)
   IMPORTANT:
   Replace the FROG Pool Tender Mineral Chamber every 6 months or after one pool season, whichever is shorter. After that time, you will hear the spent media inside, however it is no longer effective and must be replaced.

2. Replace cap and run FROG Pool Tender Cycler, with FROG Pool Tender Mineral Chamber inserted, for 10 minutes on Setting 10.

3. Insert FROG Pool Tender Algaecide into the open center of the FROG Pool Tender Mineral Chamber in the FROG Pool Tender. (See page 16 for directions.)
   Use FROG Pool Tender Algaecide for a 90-day Algae Protection Guarantee!

4. When chlorine reading is down to 1.0 ppm, which may take a few days, insert FROG Pool Tender Chlorine Chamber into the open center of the FROG Pool Tender Mineral Chamber. (See page 17 for directions.)

Step 3: Setting the Control Dial

This Cycler is designed to work effectively with a variety of pool equipment as long as the following procedures are followed. Set the control dial by matching up the parameters of your pool on the chart below. THIS IS A STARTING POINT ONLY and may need to be adjusted to fit your individual pool needs. See

2 below for adjusting directions.

IMPORTANT: If using a multi-speed pump, pump-run times of at least 6 hours per day at high speed are recommended for proper performance.
If running the pump at low speed only or on high speed less than 6 hours per day, please follow the 24 hour low-speed directions below.

**POOL SIZE Gallons Diameter| SINGLE SPEED PUMP OR HIGH SPEED PUMP RUN TIME
---|---
8 HOUR PUMP RUN TIME ****12 HOUR PUMP RUN TIME ****24 HOUR PUMP RUN TIME
** 1/2 hp| PUMP SIZE 3/4 hp          1 hp| 1 ½ hp| 1/2 hp| PUMP SIZE 3/4 hp   1 hp| 1 ½ hp| 1/2 hp| PUMP SIZE 3/4 hp         1 hp| **** 1 ½ hp
7,000| (18’)| 5.0| 4.5| 4.0| 3.5| 4.5| 4.0| 3.0| 5.0^| 3.5| 3.0| 2.5| 4.0^
9,000| (21’)| 5.5| 5.0| 4.5| 4.0| 5.0| 4.5| 4.0| 5.5^| 4.0| 3.5| 3.0| 4.5^
12,000| (24’)| 6.0| 5.5| 5.0| 4.5| 5.5| 5.0| 4.5| 4.0| 4.5| 4.0| 3.5| 5.0^
15,000| NR| 6.0| 5.5| 5.0| 6.0| 5.5| 5.0| 4.5| 5.0| 4.5| 4.0| 3.5
20,000| NR| NR| 6.0| 5.5| NR| 6.0| 5.5| 5.0| 5.5| 5.0| 4.5| 4.0
25,000| NR| NR| 6.5| 6.0| NR| 6.5| 6.0| 5.5| 6.0| 5.5| 5.0| 4.5

^ – Bypass installation recommended. See “Installation Tips” on page 6. NR – This pump size is not recommended for this size pool.
RECOMMENDED FLOW RATE: 20-60 gpm

24 HOUR, LOW-SPEED PUMP-RUN TIME
In order to ensure proper performance when running the pump on low speed for 24 hours per day or high speed less than 6 hours per day, bleed the air while the pump is on by unscrewing the knob on the back of the Cycler near the cap until water appears. Then screw the knob back on. Repeat this process each time the cap is removed for any reason. Set the control dial at #6 and follow the adjustment directions below to determine the correct setting for your pool.

EXAMPLE

POOL SIZE Gallons Diameter| 12 HOUR PUMP RUN TIME
---|---
1/2 hp| 3/4 hp| PUMP SIZE 1 hp| 1 ½ hp
7,000| (18’)| 4.5| 4.0| 3.0| 5.0^
9,000| (21’)| 5.0| 4.5| 4.0| 5.5^
12,000| (24’)| 5.5| 5.0| 4.5| 4.0
15,000| 6.0| 5.5| 5.0| 4.5
20,000| NR| 6.0| 5.5| 5.0
25,000| NR| 6.5| 6.0| 5.5

Find your starting dial setting by matching up the parameters of your pool on the above chart. An above ground pool with approximately 12,000 gallons, with a 1 horsepower pump running 12 hours a day, would require a starting setting of 4.5.

For the first week, test the pool water daily for free chlorine with FROG Test Strips to ensure correct dial setting. Continue to test weekly throughout the season.
IMPORTANT: Control dial settings in excess of these recommendations could result in excess trichlor levels being discharged into the pool. This can result in bleaching or discoloration of areas around the pool inlet or, in some cases, bleaching or discoloration of the entire pool liner or paint. In addition, excess trichlor in the pool can create health hazards to bathers.

After each testing, adjust the dial up by 1/2 increment if the free chlorine reading has dropped below 0.5 ppm or adjust down by 1/2 increment if the reading has risen above 1.0 ppm. Continue this process each day until the free chlorine reading stabilizes to at least 0.5 ppm. Remember to adjust dial by 1/2 increments only in order to prevent over chlorination which may bleach pool surfaces.

Step 4: Routine Pool Care

1. Run filtration enough hours to circulate all water 1 to 2 times per day. More than that could result in over chlorination.
   WARNING
   To prevent the build up of gas pressure in the FROG Pool Tender Cycler, be sure the pool return line valves are open –except when opening or servicing the unit.

2. Regularly test water with FROG Test Strips to maintain pH and Total Alkalinity.
   NOTE: Water balance is affected by bather load, chemical usage, evaporation and the makeup of source water, so maintaining water balance regularly is important.

3. Maintain 0.5 to 1.0 ppm free chlorine level at all times.
   Note: These lower chlorine levels are only acceptable when using FROG minerals.
   DANGER
   Do not contaminate the FROG Pool Tender Cycler, FROG Pool Tender Mineral Chamber, FROG Pool Tender Chlorine Chamber or FROG Pool Tender Algaecide with dirt, organic matter, pool chemicals (such as calcium hypochlorite or pool shocks), fertilizers or other household chemicals. Contact between any of these substances and the FROG Pool Tender Cycler, FROG Pool Tender Mineral Chamber, FROG Pool Tender Chlorine Chamber or FROG Pool Tender Algaecide, will result in a chemical reaction with the generation of heat, liberation of hazardous gasses and fire or explosion.

4. Shock the pool every other week or as needed. We recommend a non-chlorine shock as reducing chlorine use is the goal of FROG products. However, using a chlorine shock is OK too.
   DANGER

   • Never add any other types of chlorine or shock treatments through the skimmer These products should be added directly into the pool if required.
   • Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.

5. Before closing the pool for winter, use FROG Pool Tender Algaecide following the directions on page 16.

6. Remember to replace FROG Pool Tender Mineral Chamber and all other FROG Pool Tender replacements as directed.

Replacing a FROG Pool Tender Mineral Chamber

Must be replaced every 6 months or after one pool season.

1. Check the top of the box and back label of product to make sure you have the correct FROG Pool Tender Mineral Chamber to fit your FROG Pool Tender Cycler.
   IMPORTANT: The FROG Pool Tender Mineral Chamber must be replaced every 6 months or after one pool season, whichever is shorter.

2. IMPORTANT: Remove and read the information card.
   Please note: Complete instructions for inserting a FROG Pool Tender Mineral Chamber, FROG Pool Tender Algaecide and FROG Pool Tender Chlorine Chamber are included inside the FROG Pool Tender Mineral Chamber.
   DANGER

   • Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.

3. Turn off pump and turn control dial to Setting 0. This reduces the flow of water into the unit when the cap is open.

4. Open FROG Pool Tender Cycler cap.

5. Remove the FROG Pool Tender Chlorine Chamber and if not empty, set to the side or store for winter. Then remove the FROG Pool Tender Mineral Chamber and discard if it has been used for one pool season or 6 months, whichever is shorter.

6. Find slot on side of FROG Pool Tender Mineral Chamber and line up with fin inside the FROG Pool Tender Cycler. Lower FROG Pool Tender Mineral Chamber into FROG Pool Tender Cycler until secure. Replace the FROG Pool Tender Chlorine Chamber inside the FROG Pool Tender Mineral Chamber to continue operating system. (See directions on page 17.)

7. Mark your calendar ahead for the six month replacement of the FROG Pool Tender Mineral Chamber. Once wetted, the time-released mineral coating of this product is effective up to 6 consecutive months or one pool season, whichever is shorter. After that time you will hear the spent media inside, however, it is no longer effective and must be replaced.

Use FROG Pool Tender Algaecide for an Algae-Protection Guarantee

NOTE: If using directly after a shock treatment, test the water first to ensure the pH is in the proper range of 7.2-7.8 and the chlorine level is no more than 4.0 ppm. Avoid using other chemicals until this product has been circulated (filtered) for at least 24 hours.
If you are not using FROG Pool Tender Algaecide, refer to page 17 for Using the FROG Pool Tender Chlorine Chamber. See FROG Pool Tender Algaecide product labeling for complete directions for use (EPA Reg. No. 53735-9).

For a preventive dose add:

• One FROG Pool Tender Algaecide for pools up to 15,000 gallons.
• Two FROG Pool Tender Algaecide for pools between 15,000 and 30,000 gallons.

DANGER
Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.
Important: If storing FROG Pool Tender Algaecide prior to use, always keep in a cool, dry place away from children and pets.

1. Remove cap from FROG Pool Tender Algaecide without removing seal.
   Turn off pump. Turn control dial to 0. Open Cycler cap. Stand back to let any chlorine fumes dissipate.

2. Insert upside down into the open center of the FROG Pool Tender Mineral Chamber pushing down firmly on FROG Pool Tender Algaecide bottle allowing key in FROG Pool Tender Cycler to puncture seal.

3. Replace cap by hand only. DO NOT OVER TIGHTEN.

4. Turn control dial to Setting 10.

5. Turn pump on for 90 minutes allowing FROG Pool Tender Algaecide to circulate through pool.

6. To remove expended FROG Pool Tender Algaecide bottle, turn pump off and turn dial to Setting 0.

7. Remove FROG Pool Tender Cycler cap.

8. Lift FROG Pool Tender Algaecide up and allow any water in the container to drain through the FROG Pool Tender Cycler before discarding in trash or offering for recycling. Do not reuse or refill this container.
   NOTE: If water shows more than a hint of blue inside FROG Pool Tender Cycler, replace the FROG Pool Tender Cycler cap, turn dial to Setting 10 and run the pump for one minute.

   • 8a. If pool size requires additional FROG Pool Tender Algaecide, repeat steps 1-8.
   • 8b. When water is clear in the FROG Pool Tender Cycler, insert a FROG Pool Tender Chlorine Chamber according to the instructions on page 17.

Using the FROG Pool Tender Chlorine Chamber

FROG Pool Tender Chlorine Chamber is required to assure up to 50% reduction in chlorine use*. FROG Pool Tender Chlorine Chamber sold separately.
(EPA Reg. No. 53735-2)

DANGER
Never use fast dissolving chlorine tablets, liquid bleach, or calcium hypochlorite in the FROG Pool Tender Cycler.

WARNING
Avoid sparks, smoking, or any open flame near FROG Pool Tender Cycler or chemicals.
IMPORTANT: Read the label on the FROG Pool Tender Chlorine Chamber carefully before using.

1. Turn pump off. Turn control dial to 0.
   Remove cap from FROG Pool Tender Cycler and stand back to let any chlorine fumes dissipate.

2. Remove colored caps by grabbing on to the lip of one cap with a pliers and pulling up until cap releases. Repeat the process for the other cap.

3. Invert FROG Pool Tender Chlorine Chamber and shake slightly until chlorine tablets fall into tower areas.

4. Line up the small leg of the FROG Pool Tender Chlorine Chamber with the small opening in the FROG Pool Tender Mineral Chamber and the large leg with the large opening. Lower FROG Pool Tender Chlorine Chamber into FROG Pool Tender Mineral Chamber until secure.

5. Replace cap by hand only. DO NOT OVER TIGHTEN.

6. The chlorine pac container is made of HDPE plastic. Non-refillable container. Do not reuse or refill this container. Rinse thoroughly before discarding in trash or offering for recycling if available.

7. Mark your calendar ahead for the approximate replacement times for the FROG Pool Tender Chlorine Chamber.

Winterizing

Turn pump off and turn dial to Setting 0.

Unscrew knob from the front of FROG Pool Tender Cycler. Allow all water to drain.

If FROG Pool Tender Chlorine Chamber still contains chlorine, wrap in plastic bag and store in shed or cool, dry, well-ventilated location away from children, pets, cars, motorcycles or anything metal that can rust, pit, etc.
If empty, rinse and recycle.

WARNING
Avoid sparks, smoking, or any open flame near FROG Pool Tender Cycler or chemicals.

Remove the FROG Pool Tender Mineral Chamber and discard in trash. You will hear spent media inside, however, it is no longer effective.

Replace the cap and knob loosely.

Troubleshooting

For more in-depth troubleshooting, go to frogproducts.com or call King Technology at 800-222-0169.

Parts List

Included with FROG Pool Tender Cycler

Replacement parts for FROG Pool Tender Cycler

FROG Pool Tender Cycler Maintenance

Replacing the Control Dial O-Rings

Turn control dial back and forth as you pull it out of the housing.

Replace both O-rings. Apply silicone lubricant that came with your FROG Pool Tender Cycler on O-rings.

Carefully insert control dial back into housing.

Replace locking pin by pushing it through the slots on the dial until it locks into place.

Replacing the Cap O-Ring

1. Remove old O-ring.
2. Place new O-ring in bottom half of groove.
3. Place your thumbs on each side of the cap over the O-ring in the groove.
4. Roll your thumbs bac k and  forth over the O-ring  while pushing upward until the O-ring falls into the top of the groove
5. Lubricate O-ring every couple of months with silicone lubricant that came with your FROG Pool Tender Cycler. DO NOT USE petroleum based lubricants.

Replacing Knobs
To replace, simply unscrew old knob and replace with the new one.

For limited warranty terms and to register your product, see frogproducts.com/reg or call 1-800-222-0169. Failure to register your product does not diminish your warranty rights.
Made in U.S.A.
Patents: kingtechnology.com/IP
6000 CLEARWATER DR | MINNETONKA, MINNESOTA 55343 800-222-0169 | frogproducts.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>