GoKnight BPHS2a Broadcast Stereo Headset User Manual

GoKnight BPHS2a Broadcast Stereo Headset

Broadcast Stereo Headset with Dynamic Boom Microphone

Part names

Refer to the figures and confirm the parts of the headphones before use.

1. Head pad

2. Headband

3. Slider

4. Housing

5. Arm

6. Earpad

7. Gooseneck

8. Dynamic boom microphone
   BPHS2a
   

9. Condenser boom microphone
   BPHS2Ca
   

10. Temple pad
    BPHS2Sa
    

Cleaning the product

Get into the habit of regularly cleaning the product to ensure that it will last for a long time. Do not use alcohol, paint thinners or other solvents for cleaning purposes.

• To clean, wipe the main unit with a dry cloth.
• Wipe away perspiration and any other dirt from the cable with a dry cloth immediately after use. Failure to clean the cable may cause it to deteriorate and harden over time, resulting in malfunction.
• Wipe the plug with a dry cloth if dirty. Failure to clean the plug may cause the sound to cut out and may cause noise.
• Wipe the earpads and head pad with a dry cloth if dirty. Perspiration or water on the earpads or head pad may cause discoloration. Wipe with a dry cloth and allow to dry in the shade.
• If the product will not be used for an extended period of time, store it in a well-ventilated place free from high temperatures and humidity.
• The earpads, head pad, and temple pad are consumable items. They will deteriorate over time due to use and storage, so replace them when necessary. For information about replacing earpads, head pad, or other parts, or for information about other serviceable parts, contact your local Audio-Technica dealer.

Using the product

You can use the microphone on the left or right side of your face by rotating the microphone boom as shown in the figure.

Positioning the microphone boom

Use the microphone boom and gooseneck to place the microphone in the correct position.

Position the microphone boom so that the microphone is about 20 mm (0.79”) from the tip of your mouth. Positioning the microphone directly in front of your mouth will cause popping and other noise from breathing.

Connecting the product

Connect cables such as BPCB2 (included) or BPCB3 (sold separately) to the connector jack of the product.

BPCB2
Cable for BPHS2 (all models) with a TA6F connector at one end and 3-pin XLRM connector and 6.3 mm (1/4″) plug at the other.

| Function| TA6F| 3-pin XLRM| 6.3 mm (1/4″) plug
---|---|---|---|---
Microphone| MIC +| PIN 5| PIN 2 HOT| –
MIC –| PIN 6| PIN 3 COLD| –
SHIELD| PIN 1| PIN1 GND| –
Headphones| SPEAKER −| PIN 2| –| SLEEVE
SPEAKER R+| PIN 4| –| RING
SPEAKER L+| PIN 3| –| TIP

BPCB3

Cable for BPHS2 (all models) with a TA6F connector at one end and unterminated connector at the other.

| Function| TA6F| Unterminated
---|---|---|---
Microphone| MIC +| PIN 5| RED
MIC –| PIN 6| YELLOW
SHIELD| PIN 1| COPPER
Headphones| SPEAKER −| PIN 2| BLACK
SPEAKER R+| PIN 4| RED
SPEAKER L+| PIN 3| GREEN

About Hearing Damage

WARNING!

USE AS LOW A VOLUME AS POSSIBLE. PERMANENT HEARING DAMAGE CAN RESULT FROM USING THIS PRODUCT AT EXCESSIVE VOLUMES.
For safe operation of this product, do not listen at excessive sound pressure levels. Most national safety and health administrations have established guidelines for maximum time being exposed to sound pressure levels before hearing damage occurs.

To protect your ears from hearing damage:

• Use the product at the lowest volume possible; turn up the volume only enough to hear.
• Be aware that ringing in your ears may indicate that the volume is set too high.
• Have your ears examined regularly by an audiologist.
• If wax builds up in your ears, stop using the product until you have seen an audiologist.
• Stop using the product if you experience ear discomfort or infection.

Specifications

Headphones

BPHS2Sa: 190 g (6.7 oz)
Accessories| Windscreen x 3, clip, pouch
Replacements/separately sold items| BPCB2 (3.0 m (9.8′) / TA6F, 3-pin XLRM, plug), BPCB3 (3.0 m (9.8′) / TA6F, unterminated), Earpad HP-M60x,Head pad

Microphone

BPHS2a/BPHS2Sa

(0.92”)
Output connector| TB6M
BPHS2Ca
Type| Back electret condenser
Polar pattern| Cardioid
Frequency response| 60 to 15,000 Hz (at 2 cm (0.79”))
Sensitivity| -45 dB (5.6 mV) (0 dB = 1 V/Pa, 1 kHz)
Output impedance| 100Ω
Maximum input sound pressure level| 140 dB SPL (1 kHz THD1%)
S/N ratio| 60 dB (1 kHz at 1 Pa, A-weighted)
Dynamic range| 106 dB (1 kHz at Max S.P.L.)
Phantom power| 11 to 52V DC, 2 mA
Dimensions| Minimum width: 12 mm (0.47”), Height: 12.7 mm (0.5”)
Output connector| TB6M

• During a wired connection with the product. Performance varies depending on the device used.

  • 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL

For product improvement, the product is subject to modification without notice.

Polar pattern/frequency response

BPHS2a/BPHS2Sa

Sound pressure scale is 5 dB per unit

• During a wired connection with the product. Performance varies depending on the device used.

BPHS2Ca

Sound pressure scale is 5 dB per unit

• During a wired connection with the product. Performance varies depending on the device used.

Customers Support

Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
©2023 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com
Made in Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>