TIFEROR 1058 Caged Ceiling Fans with Lights Instruction Manual
- May 15, 2024
- TIFEROR
Table of Contents
TIFEROR 1058 Caged Ceiling Fans with Lights
Specifications
- Size: 20”
- Weight: 12 lbs
- Model: 1058
Product Usage Instructions
Safety Rules
- Please read all safety instructions before installing your ceiling fan and keep this document for future reference.
- If you are in doubt about any of the information provided or have any difficulty installing your fan, please contact our customer service at service_us@teferor.com.
- Before you begin installing the fan, shut the power off the circuit breaker for the fuse box. Read all instructions and safety information before installing your new fan.
- All wiring must be by national and local electrical codes. If you are unfamiliar with wiring, use a qualified electrician. Do not bend the blades while installing, balancing the blades, or cleaning the fan.
- Do not insert foreign objects in between the rotating fan blades. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. To reduce the risk of electric shock, disconnect the electrical supply circuit before installing the light kit. After you install the fan, make sure that all mounting components are secured to prevent the fan from falling. Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.
Tools Needed
- Screwdrivers
- Wrench
- Wire Strippers
- Insulation Tape
- Ladder
- Power drill
Packing List
- Fan body
- Remote Kit
- LED bulb*5
- Screw Pack
Safety Distance
- Carefully open the package. Remove items from the box. Place the motor body on carpet or foam to avoid damage to the finish. Do not discard fan cartons or foam inserts in case of return or repair.
- To prevent injury and damage, ensure that the hanging location allows the blades a clearance of 7.6ft (2.3m) and 20in (50cm) from any wall or obstruction.
Mounting Option
- You have two options for installation. Pick which one works best for your location. Remove any existing brackets before installation. Only use the provided mounting plate that came in your fan’s box.
For wooden ceiling:
- Use wood screws and washers (included) when securing to support the structure with an approved electrical outlet box.
- Drill pilot holes in the support structure to aid in securing the ceiling bracket.
For concrete ceiling
- Drill a hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor.
- Clean out the hole of all debris.
- Knock the expansion screw into the hole and then tighten it with a wrench.
Check the Connection
The cage is pre-assembled. It is highly suggested that you should check and secure the connection of the cage and cross frame again. The loose connection will cause knocking while running.
NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box. Install 4 E-26 LED bulbs (Included).
FAQ:
Q: What should I do if my fan blades are not rotating smoothly?
- A: Check if any obstructions are preventing the blades from rotating freely. Ensure that the installation site allows enough clearance for the blades to move without any hindrance.
Q: Can I use a different type of bulb with this fan?
- A: It is recommended to use E-26 LED bulbs as specified in the packing list for optimal performance and safety.
Safety Rules
- Please read all safety instructions before installing your ceiling fan and keep this document for future reference.
- If you are in doubt about any of the information provided or have any difficulty installing your fan, please contact our customer service at service_us@teferor.com
- Before you begin installing the fan, shut the power off the circuit breaker for the fuse box.
- Read all instructions and safety information before installing your new fan.
- All wiring must be by national and local electrical codes. ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
- Do not bend the blades while installing, balancing the blades, or cleaning the fan.
- Do not insert foreign objects in between the rotating fan blades.
- Make sure the installation site you choose allows the fan blades to rotate without any obstructions.
- To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit before installing the light kit.
- After you install the fan, make sure that all mounting components are secured to prevent the fan from falling.
- Turn the fan off and wait for the blades to stop completely before performing any maintenance or cleaning.
Installation
Tools Needed
You may need the tools below:
- Screwdrivers
- Wrench
- Ladder
- Wire Strippers
- Insulation Tape
- Power drill
Packing list
- Fan body
- LED bulb*5
- Remote Kit
- Screw Pack
Safety Distance
- Carefully open the package. Remove items from the box. Place the motor body on carpet or foam to avoid damage to the finish. Do not discard fan cartons or foam inserts in case of return or repair.
- To prevent injury and damage, ensure that the hanging location allows the blades a clearance of 7.6ft. (2.3m) and 20in(50cm) from any wall or obstruction
Mounting Option
- You have two options for installation. Pick which one works best for your location.
- Remove any existing brackets before installation. Only use the provided mounting plate that came in your fan’s box.
- You must be able to secure the fan to the building structure or fan-rated outlet box.
- For wooden ceilings use wood screws and washers (included) when securing to support the structure with an approved electrical outlet box.
- Drill the pilot holes in the support structure to aid in securing the ceiling bracket
- For concrete ceiling drill a hole in the base material with a hammer drill and a correctly sized carbide drill bit for the anchor and clean out the hole of all debris.
- Knock the expansion screw into the hole and then tighten it with a wrench.
Check the Connection Installing Bulbs
- The cage is pre-assembled. It is highly suggested that you should check and secure the connection of the cage and cross frame again.
- The loose connection will cause knocking while running.
- NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at the fuse box.
- Install 4 E-26 LED bulbs (Included)
Hanging the Fan
- Lift the fan towards the ceiling to suspend it from the mounting bracket using a security cable loop and washer hook.
- Then you can start wiring without holding it.
Electrical Connections
- Insert the receiver into the top of the fan body and make wire connections according to wire colors, labels, and the diagram above.
- Wrap each wire connector separately with electrical tape as an extra safety measure.
- After the wiring is finished, leave the receiver in the bracket and secure it the the electrical tape then secure the canopy to the bracket
Mounting the Fan
- Once wire connections are completed, lift the fan body and carefully align the collar with the mounting bracket. Tabs on the bracket should seat into the channel on the inside of the fan collar.
- Rotate the fan so that the set screw holes on the fan body align with the set screw holes on the mounting bracket. Take care to not pinch or damage internal wires. Insert and firmly tighten two canopy screws from the screw pack.
- Note: Do not tighten down set screws until all four screws are partly screwed in.
Maintenance
Here are some suggestions to help maintain your fan
- Because of the fan’s natural movement, some connections may become loose.
- Check the support connections, brackets, and blade attachment twice a year. Make sure they are secure.
- Clean your fan periodically to help maintain its new appearance over the year.
- Do not use water when cleaning. This could damage the motor, or possibly cause electrical shock.
- Use only a soft brush or lint-free cloth to avoid scratching the finish. Cleaning products may damage the finished
- There is no need to oil your fan. The motor has permanently lubricated bearings.
- If installed in a coastal, humid environment, regular surface cleaning may be necessary to avoid deterioration or oxidizing effects of salt or other corrosive elements.
- A Damp Location rating is not an assurance of finish durability.
- Preventative measures should be taken depending on the environmental exposures your fan will undergo to preserve and protect the finish quality and appearance of your fan.
WARNING
- Before servicing or cleaning your fan, switch the power off at the service panel and lock the service disconnecting means to prevent the power from being switched on accidentally.
Troubleshooting
- Please read all installation instructions carefully.
- After reviewing the following tips, if you are unable to solve a problem, please contact customer service for additional assistance
Fan not responding to remote control
- Check that all wire connections are secure and made as instructed.
- Verify that power is on and reaching the receiver by a voltmeter.
- Verify that controller batteries are installed with proper polarity as indicated inside the battery cover Light does not work
- Check wire connections at the ceiling and receiver.
- Confirm that LED wire leads and terminal block are properly connected to the LED board.
The fan makes a repetitive ticking noise
- Check for obstructions in the rotor path.
- Make sure the mounting hardware at the ceiling is secure.
- Make sure all other hardware and blade attachments are tight.
- Give the fan an adequate “Break in Period” of several hours to several days then repeat the steps above.
The fan makes a humming noise
- Be sure you are using the control set supplied with your fan.
- Make sure all fittings are firmly secured. Loose parts will often cause vibrational noise or humming.
- Removal and re-attachment can sometimes remedy such resonant vibrational noise.
Fan wobbles
- Make sure the mounting plate and hardware at the ceiling are secure and firmly fastened.
- If necessary, use the wood screws provided to further secure the outlet box to the joist.
- Carefully lower the motor housing and verify that the mounting plate is secure to the outlet box, the screws are tight.
- For Any Problems Contact Customer Service: service_us@teferor.com
Documents / Resources
|
TIFEROR 1058 Caged Ceiling Fans with
Lights
[pdf] Instruction Manual
1058 Caged Ceiling Fans with Lights, 1058, Caged Ceiling Fans with Lights,
Ceiling Fans with Lights, Fans with Lights
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>