EVOCHARGE iEVSE 32 Amp Wi-Fi Charging Station Installation Guide
- May 15, 2024
- EVOCHARGE
Table of Contents
EVOCHARGE iEVSE – Connecting to local Wi-Fi
Instruction Guide
RESIDENTIAL USERS:
Use the Quick Start Guide provided with your charger to connect to the user
portal. You will not be able to connect to this commercial portal.
IMPORTANT SAFETY INSTRUCTIONS
This document contains instructions and warnings that must be followed when
installing and using the Electric Vehicle Supply Equipment (EVSE).
Before installing or using the EVSE, read this entire document as well as
WARNING and CAUTION markings in this document.
Safety Instructions
The symbols used have the following meaning:
WARNING: RISK OF PERSONAL INJURY
WARNING: RISK OF ELECTRIC SHOCK
WARNING: RISK OF FIRE
CAUTION: RISK OF DAMAGE TO THE EQUIPMENT
- The charging station must be installed and repaired only by a licensed electrician.
- Make sure that the materials used, and the installation procedures follow local building codes and safety standards.
- The information provided in this manual in no way exempts the user of responsibility to follow all applicable codes or safety standards.
- This document provides instructions for the charging station and should not be used for any other product. Before installation or use of this product, review this manual carefully and consult with a licensed contractor, licensed electrician, or trained installation expert to make sure of compliance with local building codes and safety standards.
- CAUTION: To reduce the risk of fire, connect only to a circuit provided with the minimum branch circuit overcurrent protection requirements in accordance with the National Electrical Code, ANSI/NFPA 70, and the Canadian Electrical Code, Part I, C22.1.
OVERALL WARNINGS & CAUTIONS
WARNING: RISK OF ELECTRIC SHOCK
Basic precautions should always be followed when using electrical products,
including the following:
- Read all the instructions before using this product.
- This device should be supervised when used around children.
- Do not put fingers into the EV connector.
- Do not uses this product if the flexible power cord or EV cable is frayed, has broken insulation, or any other signs of damage.
- Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage.
WARNING: RISK OF ELECTRIC SHOCK
Improper connection of the equipment grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or serviceman if you are
in doubt as to whether theproduct is properly grounded.
WARNING: RISK OF ELECTRIC SHOCK
- Do not touch live electrical parts.
- Incorrect connections may cause electric shock.
WARNING: This equipment is intended only for charging vehicles that do not require ventilation during charging. Please refer to your vehicle’s owner’s manual to determine ventilation requirements.
Overview
This guide provides instructions on how to connect your EVOCHARGE iEVSE to
local Wi-Fi signal. Note, this step is only required when using the optional
third party OCPP network service with the EVOCHARGE iEVSE and iEVSE Plus
charging station products.
1.2 Access the EVOCHARGE Web Portal via Wi-Fi Connection
-
First, we need to connect a laptop or mobile phone to the EVOCHARGE iEVSE. Each EVOCHARGE iEVSE has a unique Wi-Fi signal that is identified based on the unique serial number of the charging station. To start, first note down the serial number of the EVOCHARGE iEVSE charging station you would like to connect to via Wi-Fi.
a. The unique serial number is located on the Product ID label located on the side of the charging station and will consist of the following structure: “1EO3-1-YYMM-XXXXX” (e.g. 1EO3-1-1836-00104) -
Next, using laptop or mobile phone, proceed with setting up a Wi-Fi connection and locate the EVOCHARGE iEVSE Wi-Fi signal that correlates with the unique serial number.
a. The Wi-Fi signal name will consist the following structure: “IC3-YYMMXXXXX” (e.g. IC3-183600104), as shown below:a. Next, click “Connect” and proceed to enter the password (network security key). The network security key correlates to the unique serial number of each EVOCHARGE iEVSE and consists of the following structure: “YYMMXXXXX@IC3” (e.g. 183600104@IC3).
b. Upon successful Wi-Fi connection to the EVOCHARGE iEVSE charging station, you will see the unique WiFi signal connection such as shown below:
Web Portal Access & Overview
1.3.1 Web Portal Access
- Once your laptop or cellular phone is connected to the EVOCHARGE iEVSE charging station via Wi-Fi, open a web browser (e.g. Google Chrome or Internet Explorer) and enter the following IP address into the address bar and press “enter”:
32A Product: 192.168.100.1 or click on the following hyperlink: http://192.168.100.1
40A Product: 192.168.200.1 or click on the following hyperlink: http://192.168.200.1
Once the IP address is entered, you should see the EVOCHARGE Web Portal login
screen: Note: You may receive a webpage
security warning message after entering the “192.168.100.1” IP address when
accessing the Web Portal – click accept to proceed to the web portal page.
For Administrator access, use the following default user name and password:
Username: admin
32A Product – Password: EVO32iEVSE
40A Product – Password: EVO40iEVSE
Note: If any issues accessing the Web Portal as outlined above, you may
need to refresh the webpage and repeat the login process or setup a Static IP
Address on your computer. Enter the IP address: 192.168.100.1; Subnet mask:
255.255.0.0
**Web Portal Menu Overview
**
Once logged in to the Web Portal, you will see the following Menu List on the Left side of the screen:
- Configuration
- Maintenance
- EVSE Status
- LLM Status
- Security
1.4.1 Communication Settings Tab
Clicking on the “Configuration” and then “Communication Settings” link will
bring up the following screen:On this page you can set up the Wi-Fi
network connection by completing the following steps:
- Under the “Wi-Fi Settings” section, click the “Scan” button to the right of the “SSID” field.
- Next, click the drop-down menu under the “SSID” field and locate the local Wi-Fi signal you would like to connect the charging station to.
- Once the Wi-Fi signal you would like to connect to is selected, enter the Wi-Fi password within the “Password” field. Note: The password field is a masked entry, care must be taken to enter the password correctly in order to allow for successful Wi-Fi connection.
- To finish, click the “Apply” button at the bottom-right of the “Communication Settings”.
- If the Wi-Fi connection is successful, you will see a Wi-Fi signal icon at the bottom-right of the EVOCHARGE iEVSE OLED display screen.
EVOCHARGE® Local Wi-Fi Connection Guide 701034 REV B
www.evocharge.com
Documents / Resources
|
EVOCHARGE iEVSE 32 Amp Wi-Fi Charging
Station
[pdf] Installation Guide
iEVSE 32 Amp Wi-Fi Charging Station, iEVSE, 32 Amp Wi-Fi Charging Station, Wi-
Fi Charging Station, Charging Station, Station
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>