SELTZA-RO Reverse Osmosis Filter User Guide

: May 15, 2024
: SELTZA

Table of Contents

SELTZA-RO Reverse Osmosis Filter
WHAT’S IN THE BOX
INSTALLATION
TECHNICAL DATA
INDICATORS
OPERATION
INSTALLATION SAFETY
FAQs
WARRANTY TERMS & CONDITIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SELTZA-RO Reverse Osmosis Filter

WHAT’S IN THE BOX

$SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $1$$ $SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $2$$

INSTALLATION

INSTALLATION DIAGRAM

$SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $3$$

a – Power Supply
b – Do not use
c – Filter Water Outlet
d – Wastewater
e – Supply (Feed Water)
f – 3-way Ball Valve
g – Saddle Drain
h – Power Outlet
i – P-trap drain

INSTALLATION PROCEDURES

STEP 1
- Shut off the water supply, then drain the sink faucet’s remaining water.
- Using an adjustable wrench, remove the existing angle valve under the sink, then replace it with the provided 3-way angle valve.
- Note:
- If your water supply pipeline is 3/8″ use the additional adapters for the water supply valve.
- If your supply pipeline is 1/2″ the adapters are not needed.
- Reminder: Extra caution is needed when tightening the angle valve. Make sure it is aligned and not over-tight.
- Warning: This product is intended only for cold water. Connecting to the hot water supply will damage the unit and void the warranty.
STEP 3
- Find a suitable location under the sink to place the Seltza RO unit, then connect the provided hoses to the outlets at the back of the unit (Fig. 1.1)
- A. Connect the hose from the 3-way angle valve to “Supply” (feed water) (1)
- √ Reminder: To avoid confusion, coil or loop the excess hose after connecting each end.
- B. Connect another hose to the drain saddle inlet from the Waste outlet marked “Waste” (2)
- C. Connect another hose from the RO water outlet to the sink faucet (3)
STEP 4
- Make sure all 3 filters are properly installed and hose connections are securely done before proceeding to the next steps.
- Now connect the power adaptor in the RO unit, then plug it into the power outlet. (Fig. 1.2) Automatically the light indicator will flash.
STEP 5
- Turn On the water supply. Test the unit.

TECHNICAL DATA

$SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $8$$

INDICATORS

$SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $4$$

CARTRIDGES

$SELTZA-RO-Reverse-Osmosis-Filter-FIG-1 $5$$

Note: Always follow the manufacturer’s filter replacement cycle. Failure to do so will result to poor water condition.

OPERATION

INDICATORS:

From left to right, 1-3 indicators are filter cartridge life indicators, and the fourth indicator is status indicators, both red and blue;
The indicator light coincides with the touch button.

After the machine is powered on, it will flush automatically for 18s. At this time, the blue light of the fourth lamp flashes.
Long press the fourth button for 3s to manually flush 18s. At this time, the fourth light flashes blue.
In the water/non-water state, light No. 4 is steady blue.
When the machine makes water continuously for half an hour, all valves are automatically closed, all lights are flashing (the fourth light is blue) and accompanied by a buzzer alarm, water production stops. In this state, the machine must be powered on again before it can be reset.
If the machine does not make water for 24 consecutive hours, it will flush automatically for 18. At this time, the fourth light flashes blue.
When the machine detects water leakage, all valves will automatically close, all small lights will blink (the fourth light will blink red), and the buzzer will sound an alarm to stop water production. In this state, the machine must be powered on again before it can be reset.
When the filter cartridge service life is normal, the corresponding indicator light is steady blue.
When the life of the filter cartridge is about to expire, the corresponding indicator light flashes red; When it expires, the corresponding indicator light is steady red. In these two states, long press the corresponding filter key for 3s to reset the service life of the filter cartridge. After the reset, the corresponding indicator light of the filter cartridge will turn into a blue light.
All flushing conditions can be interrupted, and the flushing valve sequence is opened: wastewater valve – inlet valve – pump; Flushing is turned off in reverse order to flushing on.
If you press the key for 3s, there will be prompt tone feedback. If you release the key for 3s, there will be release tone feedback.

INSTALLATION SAFETY

INSPECTION REMINDERS

Unboxing:
- Inspect the package for any sign of damage, such as watermarks or punctures, before proceeding.
Unit Appearance:
- Check the unit for any visible damages such as unit box breakage, or missing parts. Make sure everything is intact before installation.
Inventory:
- Make sure all supply parts are complete before proceeding.
Inquiries:
- Please feel free to reach out to our Customer Care Center with any questions you may have; our email address is support@seltzatap.com, our Customer Care direct line is 604-829-0075 and our website is Make sure all supply parts are complete before proceeding.
Installer:
- If you are not familiar with or not authorized to install the unit, we advise you to hire a professional plumber. Seltzatap will not be held liable for any property damage or personal injury during installation.
Tools:
- Please use proper plumbing tools.
Safety:
- Always observe your surroundings for any potential electrical hazards, pipe pressures, sharp objects, and other potential hazards.

FAQs

Q: Does it have a built-in pump?
- A: Yes. The built-in pump is just enough to run the system.
Q: Can SeltzaRO wastewater be recycled?
- A: Filtering it multiple times can damage the system. It is recommended for use in watering plants or similar purposes, but not suitable for bathing.
Q: Should I follow the cartridge replacement duration?
- A: It is recommended to follow the filter replacement schedule. However, the filter condition may vary depending on your local water supply. Some local water supplies may already be processed when they reach your tap.
Q: Can it operate continuously for long hours?
- A: To prolong the unit’s service life, it is advisable to have a 15-minute rest interval after 45 minutes of continuous operation.
Q: Can it be installed in an RV unit?
- A: Yes, from 120V, its power source can be alternatively connected to a 24Volt system using a proper adaptor.
Q: Will the SeltzaRO system still work during a power outage?
- A: No. There’s a pump inside the system, that needs 12V power. But a 24 DC Volt will do using another adaptor
Q: Does the Seltza RO system neutralize pH levels?
- A: No. The filtration system still depends on the existing water pH level.
Q: Will the hard water soften after it passes through the RO filters?
- A: It will reduce Calcium and Magnesium content but does not guarantee that it will soften your water quality drastically.
Q: Is it normal that the indicator light goes out after a few minutes of inactivity?
- A: That is normal, the LED indicator will resume when it is used again.
Q: Can the Seltza RO system be connected to a refrigerator or icemaker?
- A: Yes, however, it may need higher pressure so a small pump is needed.
Q: How much room is required under the sink to install?
- A: 140×440×405mm (5½2 X 17⅜ X 16inches)
Q: Does it filter fluoride?
- A: Yes. Reverse Osmosis filters fluoride.

WARRANTY TERMS & CONDITIONS

Any claim under this warranty must be made within 1 year of the date of purchase of the product.
This product is warranted to be free of defects in material and workmanship for one (1) year from the date of purchase. Products that arrived damaged will be replaced for free, which will not be taken as a fulfilled warranty.
The warranty only applies to the SeltzaRO System but does not include the accessories attached to it.
The warranty does not cover the defects or damage arising from improper use or maintenance, normal wear and tear, commercial use, accident, or external causes.
Products that arrived damaged will be replaced for free, which will not be taken as a fulfilled warranty.
The warranty only applies to the SeltzaRO System but does not include the accessories attached to it.

TO BE ELIGIBLE FOR THE WARRANTY COVERAGE, YOU NEED:

Provide valid proof of purchase details as and when required, including but not limited to the order ID, receipt, or sales invoice.
Confirm with us whether to return the original Seltza RO System unit to us, which depends on the specific conditions.
Each order is eligible for only one free replacement warranty.

Please feel free to reach out to our Customer Care Center with any questions you may have; our email address is support@seltzatap.com, our Customer Care direct line is (604) 829 0075 and our website is https://seltzatap.com.