Works Bell SRD Steering Switch Case Instruction Manual
- May 15, 2024
- Works Bell
Table of Contents
Works Bell SRD Steering Switch Case
Specifications
- Product Name: SRD steering switch case
- Compatible Models: Toyota Hiace 200 series 4-7 types
- Manufacturer: Works Bell Co., Ltd.
- Address: 8507 Tamagawa, Chino City, Nagano, Prefecture 391-0011
- Contact: Works Bell Customer Center
- Telephone: 0266-70-1477
- Email: support@worksbell.co.jp
Installation Instructions
Before starting work, disconnect the (-) terminal of the battery and wait for
about 10 minutes.
Ensure that the steering boss is already installed. If an aftermarket steering
wheel is present, remove it. Refer to the= steering boss instruction manual
for installation.
- Check for any defects in the product during temporary fitting.
- Install the SRD steering switch case correctly at a specialized shop.
- Connect the blue terminal of the flat bullet coming out of the 12-pin connector to the horn (+).
- If there is no abnormality in the operation check, fully tighten the steering wheel.
Component Parts
| NO. | Product Name | Quantity |
|---|---|---|
| 1 | 12 pin connector | 1 |
| – | spiral cable | 1 |
FAQ
Q: Can the SRD steering switch case be installed on other vehicle models?
A: The SRD steering switch case is compatible with Toyota Hiace 200 series
4-7 types only.
SRD steering switch case instruction manual for Hiace
SRD SteeringSwitchCase for HIACE
Product name: SRD steering switch case
Compatible models: Toyota Hiace 200 series 4-7 types
[Introduction]
Thank you for purchasing the SRD steering switch case. Be sure to read the
instruction manual before installing this product on your vehicle.
Please read the instruction manual (this document) carefully and understand
its contents before installing. Also, do not allow other people to use this
product or the vehicle in which it is installed. When lending or transferring
the product, be sure to give the instruction manual (this document).
- Some buttons may not work depending on the grade or equipment.
- For vehicles that drive on circuits, etc., please use adhesive etc. when installing. (as needed)
- We are not responsible for any problems caused by installation or handling.
- As the work uses various tools, please be careful not to get injured.
- Proceed with the work with the steering wheel and front wheels running straight.
- Work in a place suitable for work (a flat, safe place with plenty of space).
[Handling precautions]
-
We are not responsible for any defects caused by installation or handling that do not follow the instructions.
-
If the case is disassembled or modified, it is not covered by the warranty.
[Precautions during work] -
Before installation, please check the screws, bolts, and clip opening holes, temporarily fit the product to the vehicle, and adjust each part.
-
Proceed with installation by temporarily tightening the screws in each part, and then fully tighten them at the end.
-
We cannot accept returns of products that have been fully installed.
-
Please be sure to check whether there are any defects in the product at the time of temporary fitting.
For installation, please install it correctly at a specialized shop etc.
If you have any other questions regarding the handling of this product, please
contact us.
- Before starting work, disconnect the (-) terminal of the battery and wait for about 10 minutes.
- Our steering boss must already be installed. *1
- If an aftermarket steering wheel is already installed, please remove it.
*1 For installation of the steering boss, please refer to the instruction manual of the steering boss.
Component part
Machine Translated by Google
Installation instructions
Introduction
Before starting work, please read this manual carefully, check that all accessories are included, and be sure to follow all instructions and precautions.
- Remove the connector from the spiral cable and plug in the 12pole connector that comes with this product.
Place the included cover on the back of the steering switch case.
Please put it on.
For short boss type, use a short cover.
- Please put it in the direction marked on the inside of the cover.
- If it is loosely attached, please fix it with double-sided tape, etc.
Once everything is installed on the vehicle, check that there is no contact between the cover and the vehicle column cover. If there is, use scissors, a cutter knife, etc. to cut it using the groove as a reference.
Be careful not to get hurt!
Attach the two types of connectors coming out of the 12-pole connector and the connector coming out of the steering switch case. (Those with the same code color)
- Insert the steering switch case into the boss and secure the steering wheel with the screws. *Screws are not included.
- Connect the blue terminal of the flat bullet coming out of the 12-pole connector to the horn (+).
- Connect the battery and operate the steering switch Please check.
- If there is no abnormality in the operation check, fully tighten the steering wheel.
- Please perform a test run and confirm that there are no abnormalities in steering operation.If there are no abnormalities, the work will be completed.
If the steering boss has a cover, The cover is not used, so please remove it before installing.
Functional explanation
[Manufacturer] Works Bell Co., Ltd.
8507 Tamagawa, Chino City, Nagano
Prefecture 391-0011 Contact: Works Bell Customer Center TEL:0266-70-1477
E-mail: support@worksbell.co.jp
Documents / Resources
|
Works Bell SRD Steering Switch
Case
[pdf] Instruction Manual
SRD Steering Switch Case, SRD, Steering Switch Case, Switch Case, Case
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>