Works Bell VAB Steering Wheel Switch Relocation Device Kit Instruction Manual

Works Bell VAB Steering Wheel Switch Relocation Device Kit

Product Information

• Specifications:
  • Product Name: SRD Steering Switch Case
  • Compatible Models: SUBARU WRX STI (VAB) D type and later
  • The SRD steering switch case is a product designed for the SUBARU WRX STI (VAB) D type and later models.
  • It is manufactured by Works Bell Co., Ltd. The product includes a 12-pin connector and a spiral cable.
• Pre-Installation Steps:
  • Before starting the installation process, make sure to read the instruction manual carefully and check that all accessories are included.
  • Disconnect the (-) terminal of the battery and wait for about 10 minutes.
  • Ensure you have the necessary steering boss (sold separately) for installation.
• Component Parts Installation:
  • Insert the blue flat bullet from the 12-pin connector into the designated hole.
  • Place the switch case in the direction marked on the inside of the cover. Secure it with double-sided tape if necessary.
• Final Steps:
  • Once all components are installed, verify that there is no contact between the cover and the vehicle column cover. Trim any excess material using scissors or a cutter knife if needed.
  • Ensure that if the steering boss has a cover, it is removed before installing the SRD steering switch case.
• Contact Information:
  • Manufacturer: Works Bell Co., Ltd.
  • Address: 8507 Tamagawa, Chino City, Nagano Prefecture 391-0011
  • Contact: Works Bell Customer Center
  • TEL: 0266-70-1477
  • E-mail: support@worksbell.co.jp.

FAQs

• Q: Can the SRD steering switch case be installed on other Subaru models?
  • A: The SRD steering switch case is specifically designed for SUBARU WRX STI (VAB) D type and later models. It may not be compatible with other Subaru models.
• Q: Do I need any additional tools for installing the SRD steering switch case?
  • A: For installation, you will need a steering boss (sold separately) and basic tools like scissors or a cutter knife for trimming if required.

Product name:

• SRD steering switch case

Compatible models:

• SUBARU WRX STI (VAB) D type and later

Introduction

Thank you for purchasing the SRD steering switch case. Be sure to read the instruction manual before installing this product on your vehicle. Please read the instruction manual (this document) carefully and understand its contents before installing. Also, do not allow other people to use this product or the vehicle in which it is installed. When lending or transferring the product, be sure to give the instruction manual (this document).

• Some buttons may not work depending on the grade or equipment.
• For vehicles that drive on circuits, etc., please use adhesive etc. when installing. (as needed)
• We are not responsible for any problems caused by installation or handling.
• As the work uses various tools, please be careful not to get injured.
• Proceed with the work with the steering wheel and front wheels running straight.
• Work in a place suitable for work (a flat, safe place with plenty of space).

Precautions

Handling precautions

• We are not responsible for any defects caused by installation or handling that do not follow the instructions.
• If the case is disassembled or modified, it is not covered by the warranty.

Precautions during work

• Before installation, please check the screws, bolts, and clip opening holes, temporarily fit the product to the vehicle, and adjust each part.
• Proceed with the installation by temporarily tightening the screws in each part, and then fully tightening them at the end.
• We cannot accept returns of products that have been fully installed.
• Please be sure to check whether there are any defects in the product at the time of temporary fitting.
• For installation, please install it correctly at a specialized shop etc.
• If you have any other questions regarding the handling of this product, please contact us.
• Before starting work, disconnect the (-) terminal of the battery and wait for about 10 minutes.
• For installation, our steering boss (sold separately) is required. *1
• If an aftermarket steering wheel is already installed, please remove it.
• 1 For installation of the steering boss, please refer to the instruction manual of the steering boss.

Component part

Installation instructions

Functional Explanation

CONTACT

• Manufacturer Works Bell Co., Ltd.
• 8507 Tamagawa, Chino City, Nagano Prefecture 391-0011
• Contact: Works Bell Customer Center
• TEL: 0266-70-1477
• E-mail: support@worksbell.co.jp.
  

SRD steering switch case instruction manual for SUBARU WRX STI SRD SteeringSwitchCase for SUBARU WRX STI

Documents / Resources

| Works Bell VAB Steering Wheel Switch Relocation Device Kit [pdf] Instruction Manual
VAB Steering Wheel Switch Relocation Device Kit, VAB, Steering Wheel Switch Relocation Device Kit, Wheel Switch Relocation Device Kit, Switch Relocation Device Kit, Relocation Device Kit, Device Kit, Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>