Totnz TZMTK1 Fixed TV Wall Mount Low Profile Instruction Manual
- May 15, 2024
- Totnz
Table of Contents
Tilt TV Wall Mount
Instruction Manual
(A)
Model: TZMTK1
Thank you for choosing this product! We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at jko2yu@outlook.com.
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
DO NOT understand the instructions or have any concerns or questions, please
contact our customer service at
jko2yu@outlook.com.
CAUTION: Avoid potential personal injuries and property damage!
-
DO NOT use this product for any purpose that is NOT explicitly specified in this manual.
DO NOT exceed weight capacity.
We are NOT liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use. -
This product is designed for use in wood stud, solid concrete, concrete block and brick walls.
DO NOT install into drywall alone. -
The wall must be capable of supporting five times the weight of the TV and mount combined.
Weight Restrictions
If your TV weighs more, this mount is NOT compatible.
**WARNING
** DO NOT exceed the maximum weight indicated. This mounting system is
intended for use only within the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result in failure of the mount
and its accessories, causing possible damage and or injury.
Check the VESA Pattern of TV before the Installation
75mm ≈ 3”
100mm ≈ 3.9”
200mm ≈ 7.9”
300mm ≈ 11.8”
400mm ≈ 15.7”
Minimum VESA pattern: 75mm / 3” (W) x 75mm / 3” (H)
If your TV VESA is greater than 400 x 400 mm / 15.7 x 16.7” or less than VESA
75 x 75mm / 3 x 3”, this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
jko2yu@outlook.com to find a compatible
mount.
Verify Your Wall Construction
CAUTION
DO NOT install into drywall alone. Wood Studs (with Drywall) Solid Concrete or
Concrete Block
If you are NOT sure of the wall construction, please contact our customer
service at jko2yu@outlook.com.
Tools Needed (NOT Included)
| | | | |
---|---|---|---|---|---
Phillips Screwdriver| Tape Measure| Pencil| Electric Drill| 7/16” (11mm)
Socket Wrench| 7/16” (11mm) Wrench
Tools needed for Wood Stud Installation
| |
---|---|---
Stud Finder| Awl| 5/32″ (4mm) Wood Drill Bit
Tools Needed for Solid Concrete, Concrete Block and Brick Walls Installation
|
---|---
3/8” (10mm) Concrete Drill Bit| Hammer
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged.
DO NOT use damaged or defective parts. If you require replacement parts,
contact our customer service at
jko2yu@outlook.com.
- NOTE: NOT all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
Washers Spacers
NOTE: The Spacers shown are actual size.
TV Bolts [Only one size of the bolt fits your TV.] NOTE: The bolts shown
are actual size. 
Supplied Parts and Hardware for Step
2
NOTE: The lag screw shown is actual size.
Step 1 Secure the TV Brackets [02] and [03] to the TV
Select TV Bolts
Only one size of the bolt fits your TV.
BOLT LENGTH: Verify
adequate thread engagement with bolts or bolts / spacers
combination. We recommend thread engagement by at least 5 turns.
—Too short will NOT hold the TV.
—Too long will damage the TV. **NOTE: When using the spacers, it is important to note that they can be used in multi-layers (meaning stacked). If you have any difficulty understanding how to install the TV bolts or spacers, please contact our customer service at jko2yu@outlook.com**.
CAUTION: Ensure the TV brackets [02] and
[03] are EQUALLY CENTERED on your TV and securely fastened in place.
NOTE: The bolt hole locations on your TV may vary in accordance of the
manufacturer’s design of the TV. We are only illustrating possible locations
of the bolt holes.
Option A (For Flat Back TV) Option B (For Round Back
TV)
Option C (For TV with A “Bump”)
Option D
For cable interference or inset holes, use the spacers [F1], [F2] and [F3] to
create extra space between the TV and TV brackets. 
Step 2 Attach the Wall Plate [01] to the Wall
For wood stud installation, follow STEP 2A.
For concrete installation, follow STEP 2B.
Step 2A Wood Stud Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT use a drill for tightening the lag screws! Only use a socket wrench. DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.
- DO NOT USE THE ANCHOR [A2] FOR THIS STEP.
- Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
- Any material covering the wall must NOT exceed 5/8” (16mm).
- Nominal wood stud size: common 2 x 4” (51 x 102mm), minimum 11/2 x31/2” (38 x 89mm).
- Stud center must be verified.
Use a stud finder (NOT included) to locate wood
studs or use an awl (NOT included) to verify the edges.
Mark the edge and center locations.
|
---|---
Stud Finder (NOT Included)| Awl (NOT Included)
Position the wall plate [01] at your
desired height and line up the holes with your stud center line. Level the
wall plate [01] and mark the holes. 
Drill 4 pilot holes using
a 5/32” (4mm) diameter drill bit. Make sure the depth is NOT less than 2 3/4”
(70mm).
| 2 3/4” (70mm)
---|---
Electric Drill (NOT Included)| Ø5/32” (4mm)
7/16” (11mm) Socket Wrench
(NOT Included)
Install the wall plate [01] using the lag screws [A1]. DO NOT over-tighten the
lag screws [A1].
Tighten the lag screws [A1] only until they are pulled firmly against the wall
plate.
Step 2B Solid Concrete or Concrete Block Option
WARNING:
- Avoid potential personal injury or property damage! DO NOT use a drill for tightening the lag screws! Only use a socket wrench. DO NOT over-tighten the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.
- Ensure the wall plate [01] is securely fastened to the wall before continuing to the next step.
- Any material covering the wall must NOT exceed 5/8” (16mm).
- Mount the wall plate [01] directly onto the concrete surface.
- Minimum solid concrete thickness: 8” (203mm).
- Minimum concrete block size: 8 x 8 x 16” (203 x 203 x 406mm).
- Never drill into the mortar between the blocks.
Position the wall plate [01] at your
desired height, level the wall plate [01] and mark the pilot hole locations.
Drill 4 pilot holes using a 3/8” (10mm)
diameter drill bit. Make sure the depth is NOT less than 3” (75mm). Never
drill into the mortar between the blocks
| 3” (75mm)
---|---
Electric Drill (NOT Included)| Ø3/8” (10mm)
Use the hammer to knock the anchors [A2]
into the wall. Be sure the anchors [A2] are seated flush with the concrete
surface.
Hammer
(NOT Included)
7/16” (11mm) Socket Wrench
(NOT Included)
Install the wall plate [01] using the lag screws [A1]. DO NOT over-tighten the
lag screws [A1].
Tighten the lag screws [A1] only until they are pulled firmly against the wall
plate.
Step 3 Verify Wall Mount Installation by Putting Pressure on Wall Moun
Before attaching the TV to the mount, please try to pull down the TV wall
mount with your hands to check whether it is firmly secured.
Step 4 Adjust the Tilt Angle of the TV
- Loosen the two tilt tension nuts [T] on both brackets using wrench (NOT included).
- Adjust the hooks of the brackets to the desired angles.
- Tighten tilt tension nuts with a wrench (NOT included) to fix the tilting angle of the TV.
NOTE: The tilt angles of the hooks on the TV brackets must be the
same.
Step 5 Secure the TV on to the wall plate [1] 5-1 Hang the TV with
brackets [02] and [03] onto the wall plate [01]. 
HEAVY! You may
need assistance with this step.
5-2
While pulling and holding both ropes [R], press the bottom of the TV into the
wall plate [01] until the latches lock the wall plate [01], then release the
ropes [R]. 
Step 6 Remove the TV
HEAVY! You may need assistance with this step.
-
Disconnect all cables, pull down and hold both ropes [R] while gently pulling the bottom of the TV away from the wall.
CAUTION: Avoid potential personal injury or property damage! To prevent breaking the locking latch, always pull and hold the ropes [R] down while pulling the TV away from the wall. -
Then lift the TV up and remove from the wall plate [01].
860-00182-04
Rev00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>