ELECTRICAL 4LESS RW6WW LED Dimmable Downlight Instruction Manual
- June 4, 2024
- ELECTRICAL 4LESS
Table of Contents
4LESS RW6WW LED Dimmable Downlight
Instruction Manual
GENERAL INSTRUCTIONS
These instructions should be read carefully and retained after installation by
the end user for future reference and maintenance.
These instructions should be used to aid installation of the following
products: RW6WW / RW6CW / RW6CCT
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
- If used under insulation, the insulation should be laid unbroken over the luminaire (not packed around it). Only mineral wool-style insulation may be used
- This product is for indoor use only
- This product is Class I and must be earthed
- This product is IP65 rated (IP20 from above)
INSTALLATION
Note – If this product is being used in conjunction with an external PIR or sensor, please confirm with the manufacturer of the sensors that they are compatible with LED luminaires.
-
Provide power to the required point of installation. Suitable IP-rated junction b
-
Provide power to the required point of installation
-
Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to infringe with any joists, gas/water pipes, or electrical cables used where required
-
Cut a suitable hole in the ceiling as per the cut-out details in Fig 1 ensuring that infringe on electrical cables, water/gas pipes, or ceiling joists
-
With the aid of a cross-head screwdriver, remove the cover to access the mains terminal block (see Fig. 2)
-
Connect the luminaire to the mains supply ensuring that correct polarity is observed:
L – Live (brown) E – Earth (yellow/green) and N – Neutral (blue) (see Fig. 3)
– Live (brown) E – Earth (yellow/green) and N – Neutral (blue) (see Fig 3) -
Two cables can be inserted into the push-fit terminal block in order to achieve loop-in/loop-out wiring
-
Lift both of the spring clips on the sides of the fitting and push them into the ceiling
-
Switch on and check for correct operation
ADJUSTABLE CCT FITTING ONLY (RW6CCT)
COLOUR CHANGE
- To change the colour temperature of the fitting, switch the fitting on, off, and on again within 2 seconds. Repeat this switching cycle until desired colour temperature has been achieved (see Fig. 4)
MEMORY FUNCTION
- The luminaire will always remain the same color temperature until the above switching cycle has been carried out
RESET FUNCTION
- To reset the fittings back to warm white, turn on the fittings and leave them on for 5 seconds
- Switch the fittings off/on 4 times within 6 seconds
- Upon the 4th “on” switch, all luminaires will revert back to warm white
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
This product contains a light source of energy efficiency class B (RW6CW) / C
(RW6WW, RW6CCT) to Regulation (EU) No. 2019/2015 and (UK) 2021 No. 1095.
This product contains a non-replaceable LED light source and a non-replaceable
control gear.
Clean with a soft dry cloth only, do not use aggressive cleaning products or
solvents that may damage the product.
This product is dimmable using trailing-edge dimmers, please check
compatibility before installation.
This product should be dismantled for disposal when it reaches the end of its
life. Please see the website for dismantling instructions.
This product should be recycled in the correct manner when it reaches the end
of its life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 5 years from the date of purchase. Failure to install this product in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a free-of-charge replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specifications without prior notice.
Supplied By:
(UK) Manufacturer
ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5
4LT,
www.mlaccessories.co.uk
(EU) Authorised Representative
nnuks Holding GmbH, Niederkasseler Lohweg 18,
40547 Düsseldorf, Germany,
Email:eprel@nnuks.com
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
DCMAY22_V5
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>