Totnz TZESD6B Marsail Standing Desk Adjustable Height Instruction Manual

Totnz TZESD6B Marsail Standing Desk Adjustable Height

Specifications

• Height Adjustment Range : 27.5 – 46.7 (70cm-118cm)
• Power Input: 100V-240V
• Max. Speed: 25mm/s
• Operating Noise: 50dB
• RATED Load Capacity: 176 lbs / 80 kg

Product Usage Instructions

Step 1: Assembling the Frame

1. Align the holes on the crossbar with the holes on the desk legs.
2. Insert four M6 x 25 bolts (A) into the holes.
3. Fully tighten the bolts one by one, making sure the legs fit into the grooves of the crossbar.
4. Attach the storage hook (07) to the groove on the crossbar by hand.
5. Attach the side plate (05) outside the hook and use the bolts (B) to secure them.
6. Install another side plate (05).
7. Slide the rod coupler (08) into the end of the short transmission rod (06) on the right leg.
8. Adjust uneven desk legs if necessary:
   • Measure the heights of the two desk legs to see if they are set at the same level.
   • If not, insert the transmission rod into the hole in the left leg and turn the rod by wrench to adjust the left leg until it’s level with the right leg.
   • Turn the rod clockwise to raise the left leg or anti-clockwise to lower it.
9. Ensure the long transmission rod (06) is properly inserted into the hole in the left leg.
10. Slide the rod coupler (08) to the left to connect with the other end of the long transmission rod (06).
11. Tighten the two set screws on the rod coupler (08) using the 3/32 (2.5mm) small Allen wrench (D2).
12. Before attaching the frame to the desktop, check if the rubber pads are fixed on the frame. Re-install them if necessary.

Step 2: Assembling the Desktop
For a 40 / 48 long desk:

• Use five wood dowel pins (G) to joint the desktop panel connector (F) with the desktop panel (10).

For a 55 long desk:

• Use six wood dowel pins (G) to joint the desktop panel connector (F) with the desktop panel (10).

FAQ

• Q: What tools are needed for assembly?
  A: You will need a drill and a Phillips screwdriver.

• Q: What is the power input range?
  A: The power input range is 100V-240V.

• Q: What is the maximum load capacity?
  A: The maximum load capacity is 176 lbs / 80 kg.

• Q: How do I adjust uneven desk legs?
  A: Before attaching the transmission rod, measure the heights of the two desk legs. If they are not set at the same level, insert the transmission rod into the hole in the left leg. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it until it’s level with the right leg.

Electric Standing Desk Instruction Manual

Model: TZESD6B / TZESD6V / TZESD6N TZESD7B / TZESD7V / TZESD7N TZESD8B / TZESD8V / TZESD8N

• Thank you for choosing this Totnz product! At Totnz, we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us. support@totnz.com

Specifications

• Height Adjustment Range : 27.5” – 46.7” (70cm-118cm)
• Tools Needed (Not lncluded)
• Supplied Parts and Hardware for Step 1

Assembly

Step 1 Assembling the Frame

• Align holes on the crossbar with holes on the desk legs, and insert four bolts.
• Then fully tighten the bolts one by one, making sure the legs fit into the grooves of the crossbar.
• While attaching the hook to the groove on the crossbar by hand, attach the side plate outside the hook, and use the bolts to secure them. Then install another side plate.
• Slide the rod coupler into the end of the short transmission rod on the right leg.

Adjust uneven desk legs:

• Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod by wrench to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it.
• Ensure the long transmission rod is properly inserted into the hole in the left leg. Slide the rod coupler to the left to connect with the other end of the long tansmission rod.
• NOTE: If the hole does not match, fine-tune transmission rod fit with  a wrench.
• Tighten the two set screws on the rod coupler.
• Before attaching the frame to the desktop, please check whether the rubber pads are fixed on the frame. If they have fallen off, please re-install or use the spare rubber pads to install.

High rubber pads

Step 2 Assembling the Desktop

• For 40″ / 48″ long desk, use five wood dowel pins to joint.
• For 55″ long desk, use six wood dowel pins to joint.
• Secure the desktop panels with the connectors.

Step 3 Attaching the Desktop

• Attach the frame to the desktop.
• You can use a Phillips screwdriver or a drill.
• If you use a drill, select the proper torque and speed.
• Put the adapter into the holder.
• Attach the controller and adapter with holder to the desktop.

Step 4 Connecting the Cables

Step 5 Attaching the Side Pocket
Thread the screws through holes in the side pocket and the side plate from the outside, while holding the nuts from the inside of the side plate by hand .

Step 6 Using the Controller

• Note: Please make sure that there are no obstacles when using the desk, that the desktop is not next to the wall, and that all the cables are long enough to move the desk up and down. When the screen is dark, please press any key to wake up the screen before operation.
• Suggestion: Preset the most comfortable height when you sit down to 1, the most comfortable height when you stand up to 2, and the remaining preset height can be freely set to other heights.

Raise the Desk
Press the  button to raise the desk continuously until it reaches the highest position of 46.7 ” (118cm) or the button is released.

Lower the Desk

Press the button to lower the desk continuously until it reaches the lowest position of 27.5 ” (70cm) or the button is released.

• Save Height Setting
  Store height: Four heights can be stored. When the desktop moves to a specific height, long press the 1 / 2 / 3 / 4 button for 3 seconds until the digital number flashes. After the number flashes 3 times, it will stop flashing, and the current height will be stored to that button successfully.

• Select Height Setting 1
  Press the 1 button, and the desk will move to the height that was previously set for that button. And press any key to stop running.

Select Height Setting 2
Press the 2 button, and the desk will move to the height that was previously set for that button. And press any key to stop running.
Select Height Setting 3
Press the 3 button, and the desk will move to the height that was previously set for that button. And press any key to stop running.
Select Height Setting 4
Press the 4 button, and the desk will move to the height that was previously set for that button. And press any key to stop running.
Settings
Reset|

1. Press and hold the  button to the lowest level (27.6 ” / 70cm), and release the button. Long press the  button  for 5 seconds, the screen will display “ RST”.
2. Release the  button, the screen will flash “RST”. Then continue holding it again until the desk goes down to its lowest level and comes back up slightly. Release the button, the screen will restore the digital display, and reset is complete.

Lock / Unlock|

1. Press and hold 1 and 2 buttons together for 3 seconds to turn the lock on, the screen will display “ LOC” and the buttons will be disabled.
2. Press and hold the 1 and 2 buttons together for 3 seconds again to turn the lock off, the screen will restore from “LOC” to digital display and the buttons will be available.

Change Display Height Units|

1. The factory default height unit of the desk is set to metric.
2. Press and hold 1 and 3 buttons together for 3 seconds to switch the digital display unit. When the original digital display unit is metric, it will be switched to the imperial unit, and vice versa.

---|---
Change Collision Detection Sensitivity|

1. Press and hold 1 and 4 buttons together for 3 seconds, the screen will flash “S0X” (X is the current sensitivity level. The value range of X is 0 – 3 (0: off; 1-3: highest to lowest).
2. Select other levels by pressing  or  button, and then press and hold 1 and 4 buttons together for 3 seconds again, the “S0X” on the screen will stop flashing, and the desktop will return to the current height after 3 seconds.

Set / Clear Lowest Limit|

1. Setting: Press and hold  and 1 buttons together for 3 seconds, the screen will display “ – dO” and the lowest limit is set successfully. And when the desk goes down to the lowest limit, the screen will display “ – LO”.
2. Clear: When the screen displays the lowest limit “ – LO”, press  and 1 buttons together for 3 seconds again, the screen will flash “ – dO”, and the lowest limit will be cleared.

Set / Clear Highest Limit|

1. Setting: Press and hold  and 1 buttons together for 3 seconds, the screen will display “ – UP” and the highest limit is set successfully. And when the desk goes up to the highest limit, the screen will display “ – HI”.
2. Clear: When the screen displays the highest limit “ – HI”, press and 1 buttons together for 3 seconds again, the screen will flash “-UP”, and the highest limit will be cleared.

Trouble Shooting

1. If your desk encounters the following problems, please try to reset to solve:
2. Abnormal operation.
3. The controller screen displays RET (reset).
4. The controller screen displays error message (E07, E08), but the motor drive cable is connected normally.
5. If the controller screen displays HOT (hot), please disconnect the power supply to cool down for 20 minutes.

Thank you again for choosing this Totnz product!
All of us do appreciate your product purchase. We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us. support@totnz.com
860-00477-00 Rev00

Documents / Resources

| Totnz TZESD6B Marsail Standing Desk Adjustable Height [pdf] Instruction Manual
TZESD6B, TZESD6V, TZESD6N, TZESD7B, TZESD7V, TZESD7N, TZESD8B, TZESD8V, TZESD8N, TZESD6B Marsail Standing Desk Adjustable Height, TZESD6B, Marsail Standing Desk Adjustable Height, Standing Desk Adjustable Height, Desk Adjustable Height, Adjustable Height, Height
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>