PPLEE CR1002M 5 in 1 White Noise Machine with 2 Alarm Clock User Manual

PPLEE CR1002M 5 in 1 White Noise Machine with 2 Alarm Clock

PRODUCT DIAGRAM

Buttons

1. Time/Noise Machine/ Bluetooth ON/OFF

2. Fan Sound

3. White Noise Sound

4. Lullabies Sound

5. Other Sound

6. Timer Button

7. Dimmer & DST

8. Set Time Button/ 12/24H

9. Hour& Volume Down

10. Minute& Volume Up

11. Alarm 1

12. Alarm 2
    Parts

13. Snooze & Night Light

14. Display

15. Speaker

16. Type-( Charging Jack

17. USB Charging Jack

18. DC IN Jack Port
    

WHITE SOUND SETTING

1. Press to turn on the sound machine.
2. Press to choose the sound type.
3. Short press the sound type button again to next sound Long press the sound type button to previous sound.
4. Press to decrease the volume. Press increase the volume.
5. Press again to turn off the sound machine.

4 Kinds of Sound/42 Soothing Sounds:

Fan Sound x 6 White Noise Sound x 5
Lullabies x 15 Natural Sound x 16

OUTLET POWERED & BATTERY BACKUP

1. Pull the insulator out of battery compartment to activate CR2032 backup battery.
   NOTE: Backup battery(included) doesn’t support time display, only support memorize Ti me & Alarm setting.

2. Connect the adapter to DC jack, then plug into a 100-240V AC wall power outlet.
   

TIMESETIING

1. Press button once, the display starts flashing.
2. Press button to set the hour, and press button to set the minute.
3. Press button to save time or wait for another 1 o seconds to confirm automatically.

To change 12H/24H time format

Hold press button to change 12H/24H time format.

DST SWITCH

Hold press button to active DST function, hold press it again to deactivate it.

DIMMER

Repeatedly press button to adjust the brightness of display to your preference.

TIMER

Repeatedly press button to adjust an optional timer to your preference: 15, 30, 60, 90, 120, 180, 480 minutes or continuous play.

ALARM SETTING

1. Hold press button, the alarm indicator will light up, the display starts flickering.
2. Press button to set hour, press button to set minute. then press button to confirm alarm time setting. ~
3. Press to select to your preferred ringtone. then press button to confirm your ringtone selection.
4. Press  button to adjust the alarm ring volume for your preference. then press button or wait for 1 O seconds to save alarm setting.

SettingALARM2 is the same as ALARM 1.

When alarm goes off

1. Press button to temporarily turn off alarm for 9 minutes. Alarm will ring in every next 9 minutes.
2. Press to turn off the alarm for 24 hours, the alarm indicator will still be on, alarm will be activated again after 24 hours.
3. To completely turn off the alarm, double press corresponding  button, and the indicator II m will turn off.

BLUETOOTH

CONNECTING & DISCONNECTING

1. Repeat button until it’s in Bluetooth mode.
2. Once in Bluetooth mode, the icon will flash while searching for the last connected device.
3. Open your device and select CR1002M from the Bluetooth list to start pairing.
4. Once pairing is successful, the indicator will stop flashing and a beep will sound from speaker.
5. Press button to disconnect your device from CR1002M, a beep sound to confirm the device has been disconnected successfully. You can pair a new device now.
   NOTE: If the Bluetooth connection fails, please disconnect the Bluetooth from the previous device and reconnect. When the machine has no sound, please adjust the machine and device volume.

PLAY OPERATION IN BLUETOOTH MODE

1. Repeat button to adjust the volume.
2. Press button to play or pause the music.
3. Press button to play previous music, press button to play the next music.

NIGHT LIGHT

1. Turn on NIGHT LIGHT Press button to turn on the night light.
2. Turn off NIGHT LIGHT Hold Press button for 2 seconds or press it repeatedly until the night light turns off.
3. Switch NIGHT LIGHT Color When the night light turns on, press  button to switch to the color as you desired.
   The night light colors and modes are as below: Gradient, Blue, Ice Blue, Green, White, Yellow, Red, Purple.

CHARGING PORT

The sound machine has a USB and Type-( Port to charge your phone, tablet or other devices at the same time. The maximum charge current is 1 Ampere.

FCC St1hlment

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help This device complies with part 15 of the FCC rules.
  Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CUSTOMER SUPPORT

FCC ID. 2A6CL-CR1002
Bluetooth Referenced Qualified Design ID (s) : 79808
https://www.pplee.net
Contact our experts
support@pplee.net
CR1002M
ALARM CLOCK& WHITE SOUND MACHINE CREATE YOUR PERFECT SLEEP ENVIRONMENT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>