Range Tour Car Dash Cam Front and Rear with 64GB Memory Card 5V 1.5-2A User Manual

Range Tour Car Dash Cam Front and Rear with 64GB Memory Card 5V 1.5-2A

Product Information

• Specifications:
  • Power Source: Built-in 400mA Li-polymer Battery
  • Charger: Original car charger or 5V 1.5-2A charger
  • Memory Card: 64G MicroSD card (not hot-pluggable)

Product Usage Instructions

• Charging:
  • Charge the device with the original car charger or a 5V 1.5-2A charger.
  • If the device doesn’t turn on initially, charge it for at least 5 minutes before restarting to retain settings.
• MicroSD Card:
  • Format the MicroSD card before use and format it three times a month to ensure the DVR is functioning normally.
• Power:
  • To power it on, press the Power button. Hold for 3 seconds to turn off.
  • Connect with the car charger for automatic recording when the car starts.
• TF Card Slot:
  • Do not hot-plug the memory card.
  • Turn off the device before removing the TF card.
• Switching Modes:
  • There are three modes: video, camera, and playback.
  • Stop recording before switching modes by pressing the OK button.
• Video Mode:
  • Automatically starts recording when the car engine is on.
  • Press OK to start recording when powered by a battery.
  • Mute audio by pressing Down/MIC. Stop recording by pressing OK.
• Camera Mode:
  • Enter camera mode by pressing the Mode button once.
  • Take a photo by pressing the OK button.
• Playback Mode:
  • Enter playback mode by pressing the Mode button twice.
  • Select files using the up and down buttons.
  • Play the selected video file with the OK button.
• Motion Detection:
  • Enable motion detection in menu settings.
  • The device will start recording upon detecting movement in front.
  • Requires continuous power supply for motion detection.
• Parking Monitor:
  • Automatically record for about 20 seconds after parking due to vibration or collision.
  • Enable Parking Monitor in menu settings.
  • Requires continuous power supply for Parking Monitor.

FAQs

• Q: Can I use any charger to charge the device?
  • A: It is recommended to use the original car charger or a 5V 1.5-2A charger to charge the device.
• Q: How often should I format the MicroSD card?
  • A: Format the MicroSD card before initial use and format it three times a month to ensure normal functionality of the DVR.

Precautions Tips

• Please charge it with the original car charger or 5V 1.5-2A charger.
• If it cannot be turned on for the first time, please charge it for more than 5 minutes before restarting.
• To retain the Date/Time/other settings for at least 2 hours.
• Please format the MicroSD card before using it and format it three times a month to check the DVR is in normal use.
• The menu setting is disabled during video recording.

Operation Instructions

Power

1. Built-in 400mA Li-polymer Battery
   • The device can be activated by pressing the Power button.
   • Press the Power button for 3 seconds and release it in 3 seconds, it will be turned off.
2. Connect with Car Charger
   • The device will record automatically when the car starts and then will turn off when the engine is turned off.

TF Card Slot

• The 64G memory card has been inserted into the card slot.
• A hot plug is not supported. Always turn the device off before removing the TF card.

Switching Modes

• There are three modes: video, camera, and playback.
• Mode switching is disabled during video recording.

Always stop recording by pressing the OK button before switching modes

• Press Mode once to enter into camera mode
• Press Mode twice to enter into playback mode
• Press Mode three times to return to video mode

Video Mode

• The device starts video recording automatically when the car engine is turned on.
• When powered by battery, press OK to start video recording. A red time mark on the left-hand corner of the screen during recording.
• During video recording, press Down / MIC to mute the audio recording.
• To stop recording, press the OK button

Camera Mode

• Turn on the device, press the Mode button to enter into camera mode, and you can take a photo by pressing an OK button.

Playback Mode

• Turn on the device, and press the Mode button twice to enter into playback mode.
• Press up and down to select files. Play the selected video file by pressing the OK button.

Move Detect (Motion Detection)

• Press the Menu button to enter into the menu setting, and select ON in motion detection mode.
• Press OK, and it will start to work (a red time mark on the left-hand corner).
• When motion detection mode is selected, the device will automatically start recording if there are movements in front of the device.

Notes:

• Motion Detection is only available with the power supply.
• A separate 24-hour 2-core hardwire kit(Not included) of output 5V should be purchased to provide the continuous power supply.
• It is recommended to have it installed by a 4S shop.

Parking Monitor

• After parking, it will automatically start recording for about 20 seconds due to vibration or collision with the front camera.
• Press the Menu button to enter the menu setting, and press the OK button in Parking Monitor.

Notes:

• Park mode is only available when there is power.
• The camera is equipped with a small polymer battery of 400mA, which can only be used for a few minutes without a charger.
• A separate 24-hour 2-core hardwire kit(Not included) of output 5V should be purchased to provide continuous power supply. It is recommended to have it installed by a 4S shop.
• This file will not be overridden by loop recording.
• The locked files are saved in videos with “LOCA” as the prefix.

G-sensor

• If there is a car collision, the G-sensor will trigger the device to lock the video file being produced.
• This file will not be overridden by loop recording.
• Adjust the sensitivity level in the menu setting to suit your driving style and terrain.
• Recommended 2G setting, which is relatively low sensitivity. If you choose 8G sensitivity, you will need to frequently manually format the memory card.

Notes:

• The locked files are saved in videos with “LOCA” as the prefix, while other videos with looping recordings are saved in videos with “MOVA” as the prefix.

Emergency File Locking

• During the video recording, press the Menu button to lock the video file being produced.
• This file will not be overridden by loop recording.
• The locked files are saved in videos with “LOCA” as the prefix.

Connecting a Notebook / PC

• USB cable cannot be used for recharging.
• After the USB cable is connected to the computer, it can support reading the ”USB” disk.
• Read video files on a notebook/PC by card reader.

Menu Setting

• The Menu setting is disabled during video recording.
• Always stop recording by pressing the OK button before the menu setting
• Press the Menu button once to access the video/camera/playback setting.
• Press the Menu button twice to access the system set-in mode. The date and time are to be set in the system setting.
• Press up and down to select values. Press the OK button to confirm selections, and press Menu to exit.

Troubleshooting

1. Can not record
   • Check if the memory card is properly inserted, and the storage space
   • Check the power source.
   • If there are other files in your card, or if this card has been used in another dash cam, please format the memory card in the computer first.
   • Format the TF card in the camera menu settings.
   • Press the Menu button twice to access the system setting Default Setting.
2. Image is blurred: use a clean, soft lens-cleaning cloth to gently clean the lens.
3. If the device stops functioning: reset the device with the reset button.
4. Night vision: Note pls! You use it at night if you want to get a good image as my photo. We advise you to open the car lights. There is a small polymer battery inside to remember the date and time, can only last a few minutes.
5. Recording cannot be recycled: When you open the G-Sensor function, the videos cannot cycle record.
6. The button does not work properly: Under the condition of the recording button is useless. USB cable cannot be used for recharging, After the USB cable is connected to the computer, it supports reading ”USB” disk.
7. Freeze on the startup screen:
   • Please format the memory card on the PC.
   • Change an authentic class 10 speed memory TF-Card

Specifications

Included With

WARNING:

1. This product contains small parts, please keep it away from children!
2. This product is not a toy!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>