COSTWAY FH10077 Cyclette Pedali Multifunctional Exercise Bike Instruction Manual

COSTWAY FH10077 Cyclette Pedali Multifunctional Exercise Bike Instruction Manual

Before You Start

• Please read all instructions carefully.
• Retain instructions for future reference.
• Separate and count all parts and hardware.
• Read through each step carefully and follow the proper order.
• We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
• Always place the product on a flat, steady and stable surface.
• Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.

Thank you for purchasing this product. Please read this manual carefully before operating the unit and keep the manual in a safe place for future reference.

DAILY MAINTENANCE

1. Check and tighten all the parts of the product before using it.
2. Use a damp towel to clean the product after using it and avoid chemical solvents for cleaning.

Material: Metal, PP, PVC
Power supply: 1xLR44 1.5V button cell (included in delivery)

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual before using your pedal exercise bike

We assume no responsibility for personal injury or property damage sustained by or through the use of bike.

1. It is the responsibility of the owner to ensure that all users of the pedal exercise bike are adequately informed of precautions.
2. Before beginning any exercise program, consult your physician.
3. Before using the product, please make sure that all screws, bolts, knobs, frames, and brackets have been fixed.
4. Those who suffer from heart disease or who are prohibited from doing strenuous exercise please follow your doctor’s advice to exercise properly.
5. Do not stand on the pedal, make sure to sit on a chair, sofa or bed when exercising.
6. Please do not use this product for injured or unhealed persons.
7. The product is intended for home use only.
8. Keep the product indoors, away from moisture and dust. Do not put the exercise bike in a garage or covered patio or near water.
9. Inspect and properly tighten all parts each time the exercise bike is used.
10. Keep children under age 13 and pets away from the exercise bike at all times.
11. Over exercising may result in serious injury or death. If you feel faint, if you become short of breath, or if you experience pain while exercising, stop immediately and cool down.
12. Do not use this product if you are suffering from injuries that have not healed yet.
13. Please choose a suitable chair for training, to avoid the phenomenon of unstable base caused by too high and too low.
14. If the user can’t control, the direction of the force is downward, the training vehicle will move when used, and it needs to be used against the wall.
15. Dispose of batteries in accordance with all local codes and ordinances.

If you have the following conditions, please pay attention to your exercise time and consult a doctor before use

• Have heart disease
• Have sensory impairment
• Suffering from osteoporosis or diabetes
• During pregnancy
• Have a malignant tumor
• Physical disability
• Have high blood pressure or acute illness
• Suffering from ventilation and arthritis
• There are symptoms of dizziness, tinnitus, it is recommended to consult a doctor before using the product

PARTS LIST

1. Base

2. Main Tube

3. Pedal Rod

4. Elbow Bar with a Resistance Band

5. Pedal

6. Handle

7. LCD Monitor

8. Allen Bolts (8 x 50 MM) +Cap Nut

9. Locking Knob

10. Bolt

11. Double-ended Wrench

12. Allen Key

ADJUSTING THE LENGTH OF THE BASE

• The axle tube of the base contains 6 holes, each corresponding to a unit of length and each length corresponds to a bicycle height. Depending on the height of the chair you are sitting on. Before you start exercising with this exercise bike, you need to adjust the length of the base (i.e., the height of the bike). The default length of the base is the shortest, which is the maximum height of the bike. (The spring ball is located in the hole closest to the footrests)
• If the chair you are using is lower, extend the length of the base to reduce the height of the bike (The example in the illustrations above shows how to extend the base to its longest length) Push in on the spring ball on the axle tube and pull the tube out. The spring ball will pop back out at the next hole. Repeat this step until the spring ball is at the 6th hole, furthest from the footrests. at this setting, the pedals of the bike are at their lowest.

ASSEMBLY INSTRUCTION

1. Install the main tube (2) to the base (1), and use (8) to fix them.

2. Install the pedal rod (3) to the base (1), and use (8) to fix them.

3. Mount the pedal rod (3) to the main tube (2) and use (8) to fix them.

4. Insert the elbow bar (4) to the main tube (2), and lock the knobs.

5. Hook the Resistance band

6. Install the pedal (5) to the pedal rod (3) and use (8) to fix them. Make sure the induction zone faces up.

7. Insert the locking knob (9) to tighten up.

8. Insert the handle (6) to the elbow bar (4) and use two bolts (10) to fix them.

9. Install the LCD monitor (7) to the handle (6).

10. . Insert the locking knob (9) to the handle (6).

OPERATION

• Pedaling

• Stretching

• Massaging

• Two Persons Use

THE LCD MONITOR

Auto On/Off
When the device is inactive, you can either press the button once or
just start exercising, the LCD monitor will turn on automatically. If
you don’t use the button or don’t exercise for 4 minutes, the LCD
monitor will automatically switch back to standby mode to save
power.

Function selection

Press the button. The SCAN icon flashes to indicate that the SCAN function is enabled. The display automatically shows all functions in  sequence as follows: Counter/Time/Calories/Distance/Total Counts.

Each function is displayed for 6 seconds. If you want to view a function for a long time, press the buttons soon as the function is displayed. The function will be displayed permanently.

Functions

Time: The duration of the current training (in minutes and seconds).
Calories: The number of calories burned in the current training session
Distance: Distance exercised
TCNT: Total Counts of cycling
CNT: Counts of cycling

Measurement Range

Counter: 0-9999(revolutions)
Time: 0:00-99:59 (minutes seconds)
Calories: 0-9999(calories)
Distance: 0-9999(km)
Auto Scan: 6 seconds per function

RESET

Press and hold the button for 3 seconds. Then all meter data is deleted (reset to zero) except for the number of counts.

Batteries

The LCD monitor is powered by 1 LR44 1.5V button cell battery.
When the digital display is blurred or dimmed, replace the battery.

TECHNICAL DATA

• Dimensions (LWH):17-21.5 x 17.7 x 31.1-36.6 in·
• Material: Metal，PP，PVC
• Power supply: 1 x LR44 1.5V button cell (included in delivery)

INSTRUCTION

1. Separate the top cover and the bottom cover of the electronic watch, be careful not to break the connection line.

2. The battery base is located on the back of the upper cover.
   Make the battery face upward and carefully push it into the battery base.
   Note that the latch on the battery base should be fastened.

3. Close the top cover and bottom cover.

FDS GmbH

Newer Höligbaum 36 22143 Hamburg 22143 Hamburg

The following batteries or accumulators are contained in this electronic device

Battery Type : Chemical System
LR44: zinc (Zn)

• Warning: Make sure the battery is completely drained.
• Carefully remove the battery or accumulator.
• The battery or accumulator and the device can now be disposed of separately.

Return / Damage Claim Instructions

DO NOT discard the box / original packaging.

In case a return is required, the item must be returned in original box. Without this your return will not be accepted.

Take a photo of the box markings.

A photo of the markings (text) on the side of the box is required in case a part is needed for replacement.

This helps our staff identify your product number to ensure you receive the correct parts.

Take a photo of the damaged part (if applicable).

A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.

Send us an email with the images requested.

Email us directly from marketplace where your item was purchased with the attached images and a description of your claim.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>