CR Handrail CHR2X48 Black Deck Railing Wrought Iron Handrail Post Kit User Guide
- May 15, 2024
- CR Handrail
Table of Contents
CR Handrail CHR2X48 Black Deck Railing Wrought Iron Handrail Post Kit
You made the right choice of railing!
-
Cost-Effective
-
Safe & Durable
-
Quick to Install
-
Easily Extendable (Modular)
Time Required
Ground attachment
wood – 20+ minutes
concrete – 60+ minute
Tools Required
An electric drill/hammer
An impact drill is preferred (although not required) for installing the concrete bolts for concrete steps, lag screws for wooden steps, or other ground attachments.
Means and Methods Disclaimer
In no event shall CR Handrail have any responsibility, control over, charge of, responsibility, or liability for the means, methods, techniques, sequences, or procedures, or for safety precautions in connection with the installation of the railing, since these are solely CM/GC’s, Subcontractor’s, and Owner’s responsibilities.
Each installation site differs widely ranging from the construction & condition of attachment points, local building & safety code, local construction code, and local means & methods.
CR Handrail’s installation guide (whether it be in text, illustration, video or in support discussion) constitute for ideal installation condition. There is no ideal installation in real life. There is no substitution for consulting a local licensed contractor, architect, engineer, nor code inspector.
CR Handrail’s installation hardware and tools are provided as building material and does NOT constitute as the specific nor final installation hardware. Once again, you and your installer must make the final on-site determination to the specific means and methods of installation appropriate for your installation
Following CR Handrail’s instruction does NOT constitute as proper installation as you and your installer must make the final means & method determination. Improper installation can lead to failure of rail system which can cause serious injury.
Please make sure the hardware and tools we provided will be right for your install (READ means & methods disclaimer). IT IS POSSIBLE YOU NEED DIFFERENT HARDWARE & METHODS. Please take your time to do your installation. If you are unsure or uncomfortable with the installation, we highly recommend hiring a licensed and bonded contractor.
We’ve made it easy for you to install your post!
Scan this QR code for a detailed video explanation of how to install your new handrail correctly.
Masonry Tools & Hardware Explained
-
5/16 (8mm) Anchor Bolt
-
5/16 (8mm) Masonry Drill Bit
*SDS+ available upon request
FOR CONCRETE
- Diamond Core Drill Bit
For hard stone
*available upon request
Note: This will be a tight fit. In fact, the specification calls for the drill bit and anchors to be the same size. Some installers use a 3⁄8 drill bit to make the installation easier, and other installers wiggle the drill bit to bore the top of the hole slightly bigger. (We are aware of the tight fit and we must only recommend using our masonry drill bit without wiggling).
WARNING
The strength of the anchor is dependent on the hole size & concrete integrity. A hole that’s too big or concrete that’s not up to standard grade can make the anchor wiggle or possibly come out. This is what can cause a rail to fail & fall over
Position and Mark the Holes
Post should be at least 1.5” (3.8cm) away from edges.
Ensure the post baseplate is parallel with edges.
FOR CONCRETE
Please adhere to local & statewide building code. Recommended distance from the edge is based on standard grade concrete (2500 psi).
If your concrete is ‘high strength’ concrete, the edge distance can be reduced. (See ICC Chapter 19, Table 1908.2)
Smaller drill bit (Please go straight to Step 5)
Larger drill bit (Continue to Step 3)
Ensure Correct Depth
Use the CR Handrail pencil to measure the depth of the hole with the flat end of the pencil.
Note: This is only for rough measurements. This is to endure the hole is deep enough.
FOR CONCRETE
For Wood, please go straight to Step 5.
Tip: holes must be deep enough or will have a serious issue
Install Anchors
Once the holes are made and depth verified, hammer the anchors into the holes.
Tip: Hammer the anchor with 2 washers and 2 nuts (with nut at the very tip) to prevent over insertion.
Periodically Double Check!
Put the post onto the anchor and physically verify the washer and nut has only enough thread to for the full height of the nut to screw on.
Secure Post to Ground
Use the nut socket & bit extension
What if Post Not Level?
If ground is not level, use included extra washers to shim the baseplate.
FOR WOOD
- Position the posts (along with the complete railing) over predrill holes.
- Install a washer & lag screw, one by-one
- When all are installed, doublecheck each of them again, to ensure all are tightened.
Note: If your drill has a hammer (or impact function), enable it.
FOR CONCRETE
- With all the nuts & washers removed, put the posts onto the anchor bolts (along with the rest of the rail). Install a washer & lag screw, one-by-one
- Hand-tighten a washer and nut over each anchor bolt.
- Use the electric drill to tighten the nut (turn off hammer or impact driver function).
More from CR HANDRAIL
CR Handrail’s Brackets and Covers
CR Handrail’s Top Connectors for Top Rail & Post
Warranty
5 Years’ Free Warranty
- Scan the barcode within 30 days.
- Register your product.
Or, register your product at www.crhandrail.com/5yearwarranty
Need help?
- Connect Multiple Railings
- Technical Drawings
- Complicated Installations
- Installation Error
- Missing Parts
CONTACT US
(Info Last Page)
Chi & Richard with family at San Diego Safari Park
A heartfelt message from the owners of CR Handrail
Chi is an architect and Richard is in real estate construction. With the
combined knowledge and expertise, Chi & Richard believe they can provide the
best commercial grade railing product that can be installed by anyone. They
want to take the time to say thank you. If you got the time, Chi, Richard &
the CRH team love to see a photo or video of your installation!
– Chi & Richard from CR Handrail
Your picture and video post helps those who are worried about the installation.
Susanna P
I was worried
Reviewed in Canada on October 12, 2022
Size: 4 Steps | Verified Purchase
I was a little worried that the handrail would be difficult to install. It comes with everything you could possibly need to install the railing. Hats off to the people who put the kit together.
2 people found this useful
Help Us Make a Difference:
SAFETY FOR ALL!
How can we make it easier for you?
Missing Parts?
www.crhandrail.com/parts
Support
Text with Photos
(800) 420-0432
SMSTO:18004200432:Hi CRHandrail.
WhatsApp
(775) 324-8877
Need help? Text us the picture of your problem.
Documents / Resources
| CR
Handrail CHR2X48 Black Deck Railing Wrought Iron Handrail Post
Kit
[pdf] User Guide
CHR2X48 Black Deck Railing Wrought Iron Handrail Post Kit, CHR2X48, Black Deck
Railing Wrought Iron Handrail Post Kit, Wrought Iron Handrail Post Kit,
Handrail Post Kit, Post Kit
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>