GUTA TM528 Cigarette Lighter Tire Pressure Monitor System Instruction Manual
- June 17, 2024
- GUTA
Table of Contents
Cigarette Lighter
Tire Pressure Monitor System
Monitors up to 10 tires (including 2 spare tires) in real time
Model number: TM528 (Monitor display)
Instruction ManualImplementation Standard:GB26149-2017
TPMS INTRODUCTION
1-1. ABOUT TPMS
Thanks for choosing ourTPMS products. TPMS is a system monitoring pressure and
temperature of vehicle tires in real-time, by sensors detecting the tire
conditions, and transmit the data to monitor display. With alarming conditions
set up when user, when there’s abnormal situation detected, system alerts
driver by audio alarm and displaying data in monitor, thus to aware and avoid
potential accident. Applying TPMS to vehicles can also efficiently reduce fuel
consumption, prolong tire life and save energy.
Be sure to read these instructions carefully before installation and it’s
suggested to keep this manual forfuture use.
1-2. SAFETY PRECAUTIONS
It is strongly suggested to read below instructions before TPMS installation:
- The monitor should be installed inside the vehicle driver cabin where it does not affect normal driving.
- The monitor should be firmly fixed to prevent falling off during driving.
- After sensors installed to tires, please examine it and make sure there’s no air leakage.
- The tires’ temperature and pressure could increase dramatically while driving, when it reach the alarm limits please stop vehicle to cool down and to avoid braking problem or tire blowout.
- When tire pressure is continually increasing or dropping, please stop the vehicle and examine tires.
- When high tire pressure is observed, please beware of possible tire blowout; when it’s low tire pressure beware of fuel consumption and wheel balance.
- The system can effectively monitor tire pressure and temperature but cannot avoid traffic accident. Using quality tires and keep normal pressure in tires are essentially important.
- Be sure of safety while checking tire data in monitor during driving.
- With correct installation this TPMS system issues alert when abnormal situation appears, driver does not have to check the monitor frequently but should focus in safety driving.
1-3. INSTALLATION TIPS
- After 10 minutes of no vehicle vibration detected the monitor goes into sleep mode, and can be awaken by vehicle vibration and starts receiving data from sensors. At the start some data might be missing in monitor, it’ II be displayed when tire pressure or temperature updated.
- Monitor and sensors transmit signals by wireless, with long effective transmission distance and anti”-“inference protection. Anyway in case of long vehicle it’s suggested to install an additional transceiver for effective signal transmission.
- It’s a normal situation that the tire pressure and temperature changing all the time during driving, as result of air expansion and contraction.
- Tire air leakage with time is a normal phenomenon and is not caused or affected by TPMS.
- For any question or problem of installation, please contact with local distributors.
PRODUCT FEATURES
- Reliable functions and easy installation
- Large-size LCD Monitor of Pressure and Temperature, Vehicle Battery Voltage
- Dual port 2A USB charger
- Three levels of backlight.
- Configurable high/low pressure and high temperature alert threshold
- Visual and audio alert for abnormal pressure, temperature and fast leakage Selection of pressure unit (PSI, BAR) and temperature unit ( °F /°C)
- Switch Normal Road and Off Road for different road condition ( Common road and special road)
- Long receiving distance Monitors up to 10 tires ( including 2 spare tires)
- Display temperature and pressure simultaneously
- Individual setting of high/low pressure alert threshold for each axel
PACKAGE CONTENTS
INSTALLATION
It is an easy installation the monitor using cigarette lighter adaptor (CLA) power and avoid any obstacle to driver view.Please plug in the CLA firmly to begin the normal mode operation and upon power up through CLA.Driver could turn on/off monitor manually after/before a longtime parking.
Sensor ID CODE Pairing to the Monitor
5-1 Sensor ID Code Learning
In Standby mode, long press CODE button until a “Beep” to enter Learning mode,
you will see “Id” and”–“”–“”–” flashing press “+”/”-” button to select desire
tire,” I”
Use the left front tire as an example.Place sensor near monitor like the
diagram,and short press CODE once with a beep, You will see “LF”, monitor
receives sensor code with a beep. Then “LF” disappear and new sensor ID code
is displayed the code learning successfully.
But if “LF” disappear and without new sensor ID code displayed, the code
learning failed with a double beep,please press CODE button to repeat the same
operation.Long press CODE button for 3 seconds until Beep sound will resume to
standby mode.
Note: As this is a wireless learning. Please keep other sensors at least 1
feet away from the monitor to prevent any wrong pairing.
5-2 Delete ID Code
In Standby mode, long press CODE button until a “Beep” to enter Learning
Sensor mode, press”+”/”-” button to select desire tire.Long press”-” button
until a beep, the sensor ID will be cleared. Or long press”-” button until
second “Bi Bi” will delete all sensor ID.
Hold CODE button until a Beep to save setting.
Normal Road FACTORY DEFAULT SETTING
Pressure unit: PSI
Temperature unit: °F
High temperature threshold: 158°F
Truck Front axle High pressure threshold: SSPSI,
Lower pressure threshold:33PSI
Truck 2nd axles High pressure threshold: 61PSI, Lower pressure threshold:37PSI
Truck spare tire High pressure threshold: SSPSI, Lower pressure
threshold:33PSI
Trailer High pressure threshold: l00PSI, Lower pressure threshold :60PSI
Trailer spare tire High pressure threshold: l00PSI, Lower pressure threshold:60PSI
Normal Road Parameter setting
In Standby mode,long press SET button until a Beep to enter Parameter Setting
mode, press”+”/”-” to select desire items.
6-1. Normal Road Pressure unit setting
In pressure unit setting mode, when BAR/PSI is flashing, press”+”/”-” button
to select the desired unit, press SET button once with a beep and go into
Temperature unit setting, hold SET button until a Beep to save setting.Or hold
SET&+ button for 3 seconds to abort without saving and return to Standby
mode.Or without any operation for 1 minute to abort without saving and return
to Standby mode.
6-2. Normal Road Temperature unit setting
In temperature unit setting mode, when F/C is flashing, press “+”/”-” button
to select the desired unit, press SET button once with a beep to save setting
and go into High pressure threshold setting,hold SET button until a Beep to
save setting.Or hold SET &+ button for 3 seconds to abort without saving and
return to Standby mode.Or without any operation for 1 minute to abort without
saving and return to Standby mode.
6-3. Normal Road High pressure threshold setting (Truck 2nd axles,trailer are
the same operation)
In 1st axle high pressure threshold setting mode, when 1st axle tire icons and
a pressure value start flashing,press “+”/”-” button to adjust pressure value.
Press SET button once with a beep and go into Low pressure threshold
setting,hold SET button until a Beep to save setting.Or hold SET&+ button
for 3 seconds to abort without saving and return to Standby mode.Or without
any ope ration for 1 minute to abort without saving and return to Standby
mode. ( High pressure value range 188~ 18psi)
6-4. Normal Road Low pressure threshold setting (Truck 2nd axles,trailer are
the same operation)
In 1st axle low pressure threshold setting mode, when 1st axle tire icons and
a pressure value start flashing,press “+”/”-” button to adjust pressure value.
Press SET button once with a beep to and go into High temperature setting.hold
SET button until a Beep to save setting.Or hold SET&+ button for 3 seconds
to abort without saving and return to Standby mode.Or without any operation
for 1 minute to abort without saving and return to Standby mode. ( Low
pressure value range 187~ lpsi)
6-5. High temperature setting (Truck ,trailer are the same operation)
When trailer spare tire low pressure setting is finished,press SET button once
into truck High temperature setting mode.When all truck tire icons and high
temperature value start flashing,press “+”/”-” button to adjust temperature
value. hold SET button until a Beep to save setting.Or hold SET&+ button for
3 seconds to abort without saving and return to Standby mode.Or without any
operation for 1 minute to abort without saving and return to Standby mode. (
High temperature value range from 77°F~ 199°F)
NORMAL STATE
In the normal state,if 10 sensors have been programmed, the monitor will display truck—truck spa re tire—trailer—-trailer spa re ti re pressure and temperature of all tires every 10 seconds in turn.
If the sensors have not been programmed to the monitor, the monitor will not
display the tires.
e.g. the truck and trailer without programming the spare tire, the monitor
will display truck — trailer with tire data, every 10 seconds in turn.
Off Road FACTORY DEFAULT SETTING
Long press CODE and SET button simultaneously until a beep will enter to OFF
ROAD mode.
Pressure unit: PSI
Temperature unit: °F
High temperature threshold: 158°F
Truck Front axle High pressure threshold: 28PSI, Lower pressure threshold:l
7PSI
Truck 2nd axles High pressure threshold: 31PSI, Lower pressure threshold:19PSI
Truck spare tire High pressure threshold: SSPSI,
Lower pressure threshold: 33PSI
Trailer High pressure threshold: S0PSI,
Lower pressure threshold: 30PSI
Trailer spare tire High pressure threshold: l00PSI, Lower pressure threshold:60PSI
Off Road Parameter Setting
If now in Normal Road mode, Long press CODE and SET button simultaneously
until a beep will enter to OFF ROAD mode.
Do the same operations as Normal Road Parameter setting (Page07).
Remarks: Long press CODE and SET button simultaneously until a beep will back
to NORMAL ROAD mode.
Alerts
High pressure/ Low pressure/ High temperature/ Fast leakage/ Sensor low
battery/ Sensor lost signal
When any abnormal situation is detected (e.g. when tire pressure or
temperature exceeds the threshold value), the faulty tire icon flashes with
value, warning sign and LED flash and audio beep will happen at the same time.
Press any button to stop audio warning, but the warning sign and LED keep on
flashing until problems are solved.
8-1 High pressure alert display
(e.g.: High pressure threshold is 55 PSI)
Note: When are flashing, the faulty tire pressure is too high, please deflate the tire to normal pressure.
8-2 Low pressure alert display
(e.g.: Low pressure threshold is 34 PSI)
Note: When ,U&33 are flashing, the faulty tire pressure is too low, please inflate the tire to normal pressure.
8-3 High temperature alert display
(e.g.: High temperature threshold is 158°F)
Note: When I, (l) & 159°F are flashing, the faulty tire temperature is too high, please stop vehicle to cool down to normal temperature.
8-4 Fast leakage alert display
Note: When there’s fast leakage detected in tire, sensor will send data to monitor at once, & 36 & red LED are flashing and audio beep is issued. Press any key to stop audio warning, but & 36 & red LED are still on and keeps on flashing until problems solved.
8-5 Sensor low battery alert display
Note: When 8 and I tire are flashing, the faulty tire sensor battery is almost out of power, please replace with new battery.
8-6 Sensor signal lost
When the monitor didn’ t receive the sensor signal for more than 60 minutes, there will be no sensor data.
OTHER FUNCTIONS
Three levels backlight.
Press+ button to increase screen brightness,press- button to decrease screen
brightness.
Specifications
High pressure value range | 18 ~ 188PSI |
---|---|
Low pressure value range | 1 ~ 187psi |
High temperature value range from | 77 °F ~ 199°F |
Operation temperature | -4°F ~ 176°F |
Storage temperature | -22 °F ~ 185 °F |
Operating voltage | DC 12V |
Frequency | 433.92MHz |
Dimension (LxWxH) | 170x81x49 mm |
Weight | 99g |
USB power | 2A |
CAUTIONS
- Please follow the instruction manual in use of product, factory is not responsible for any consequences caused by misuse out of instruction manual.
- Please install product according to instruction manual, the factory is not responsible for any consequences caused by un”-“proper installation out of instruction manual.
- Please set the alert threshold values according to specifications and parameters provided by tire manufacturer and its distributors, TPMS factory is not responsible for any consequences caused by faulty setting of the alarm threshold.
- This instruction manual is subject to further revisions in need without prior notification.
Get Help
We promise 2-YEAR WARRANTY and 24/7 CONSIDERATE CUSTOMER SERVICE.
If you need any help, please don’t hesitate to contact us via
[guta@afterservice.vip] and we will help you
solve the problems as soon as possible.
https://guta.afterservice.vip/utm_source=card&utm_medium=qrcode
Get 24/7 Assistance at
Use camera or QR scanner to scan
0 + 1(855)-492-9277
Mon-Fri: 9:00AM- 5:00PM (EST)
Amazon Platform: “Contact Seller”
Official Website: http://www.guta-tech.com/
Email Address: guta@afterservice.vip
https://guta.afterservice.vip
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>