Telepower TPURID2100 Module Interface User Manual
- June 5, 2024
- Telepower
Table of Contents
Telepower TPURID2100 Module Interface
Installation Procedure
This Module interface is the Board-to-Board connector as below,
| Pin No | Pin Name | Pin No | Pin Name |
|---|---|---|---|
| 1 | VIN | 2 | VIN |
| 3 | VIN | 4 | VIN |
| 5 | VIN | 6 | VIN |
| 7 | 3.3VOUT | 8 | 3.3VOUT |
| 9 | ALARM | 10 | UART_CTS |
| 11 | SPI2_MOSI | 12 | UART_RTS |
| 13 | SPI2_MISO | 14 | Reserve1 |
| 15 | SPI2_SCK | 16 | Reserve2 |
| 17 | SPI2_NSS | 18 | Reserve3 |
| 19 | UART3_RX | 20 | Reserve4 |
| 21 | UART3_TX | 22 | GPIO1 |
| 23 | UART_RX | 24 | UART2_TX |
| 25 | UART_TX | 26 | UART2_RX |
| 27 | UART4_TX | 28 | I2C1_SCL |
| 29 | UART4_RX | 30 | I2C1_SDA |
| 31 | MCU_RESETn | 32 | MCU_BOOT |
| 33 | GND | 34 | GND |
| 35 | GND | 36 | GND |
| 37 | GND | 38 | GND |
| 39 | GND | 40 | GND |
This is a user manual for host product manufacturers to use when integrating the module in a host product.
[General] : Applicable
This user manual describes the integration procedure per Sec. 2.2 to 2.12 of KDB 996369 D03.
[List of applicable FCC rules] : Applicable
This device complies with below part 15 of the FCC Rules.
Part 15 Subpart C
[Summarize the specific operational use conditions] : Not Applicable
[ Limited module procedures] : Not Applicable
[ Trace antenna designs] : Not Applicable
[RF exposure considerations] : Applicable
The following statements must be described on the user manual of the host device of this module;
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines.
This equipment should be installed and operated keeping the radiator at least
20cm or more away from person’s body.
[Antennas] : Applicable
The device is designed to use the antennas listed below. Do not modify the antenna or any other part of the module. Any modifications will invalidate the modular certifications and require new approvals for the host system.
| Model No. | Antennna Type. | Antenna Gain | Unit |
|---|---|---|---|
| ARRTN5-915.000MHz | Patch | 3.31 | dBi |
[Label and compliance information] : Applicable
Following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: WQYURID02 or Contains FCC ID: WQYURID02
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- If it is difficult to describe this statement on the host device due to the size, please describe in the user’s manual and also either describe on the device packaging or on a removable label attached to the device.
The following statements must be described on the user manual of the host device of this module;
FCC CAUTION **
**
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
[ Information on test modes and additional testing requirements] : Not Applicable
[Additional testing, Part 15 Subpart B disclaimer] : Applicable
The modular transmitter is only FCC authorized for the specific rule parts
(i.e., FCC transmitter rules) listed on the grant (FCC Part 15.247), and the
host product manufacturer is responsible for compliance to any other FCC rules
that apply to the host not covered by the modular transmitter grant of
certification.
The final host product still requires Part 15 Subpart B compliance testing
with the modular transmitter installed.
[Note EMI Considerations] : Applicable
We recommend to use “best practice” RF design engineering testing and evaluation in case non-linear interactions generate additional non-compliant limits due to module placement to host components or properties. The host manufacturer is responsible for ensuring compliance with the applicable FCC rules for the transmitters operating individually and simultaneously. This includes compliance for the summation of all emissions from all outputs occupying the same or overlapping frequency ranges, as defined by the applicable rules.
[How to make changes] : Applicable
Customer Support
Only the grantee is permitted to make permissive changes.
Please contact us at http://www.telepower.jp/en/contact.html.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>