LOCKWOOD GEN6TX Keying System Instruction Manual

May 15, 2024
LOCKWOOD

LOCKWOOD GEN6TX Keying System

GEN6TX® Technical Reference Manual

Terminology

LOCKWOOD-GEN6TX-Keying-System-FIG-1

New GENTX® Features

  • GEN6TX® keys are supplied with the new FP2 feature. The FP2 feature provides increased protection via a two-way stop-surface system. One or both shoulders on the key will contact stop surfaces on the barrel, but there are three barrel types mixed to randomize the active stop surfaces.
  • GEN6TX® keys are fully backward compatible with Generation 6 and GEN6T systems. Generation 6 or GEN6T keys cannot be used with GEN6TX® barrels.

LOCKWOOD-GEN6TX-Keying-System-FIG-3

Springs & Anti-drill Bar

Springs

LOCKWOOD-GEN6TX-Keying-System-FIG-32

Pins

T Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-6

Anti-bump Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-7

Top Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-8

Hollow Top Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-9

Master Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-10

Bottom Pins

LOCKWOOD-GEN6TX-Keying-System-FIG-11

Top Pin Usage

General
ASSA ABLOY recommends using anti-bump pins for all chambers in all Lockwood branded products except for 670 and LIW cylinders. All Lockwood branded products are tested with anti-bump pins.

Standard Top Usage
Standard top pins are recommended for use with a combined master pin and bottom pin lengths 0-9 in the cylinders listed below.
Cylinders:

  • 201
  • 255
  • 334B
  • 570
  • 570E
  • 577
  • 3570
  • 8217
  • 8219
  • 8466
  • 9555
  • NEX (includes 005 & Onyx internal Cylinder)

Non Standard Top Pin Usage
Cylinders

  • 001 (includes 680)
  • 355
  • 530
  • 691
  • 8221
  • 8474

For the above cylinder list use the following top pin lengths:
Combined master and bottom pin length 0-2 = Standard Top Pin
Combined master and bottom pin length 3-6 = Medium Top Pin
Combined master and bottom pin length 7-9 = Short Top Pin
Note: SP530-336SS Short Top Pin Spring must be used with 001, 355, 530, 691, 8221 & 8474 cylinders.

Cylinders

  • 670
  • LIW

For the above cylinder list use the following top pin lengths:
Combined master and bottom pin length 0-1 = Hollow Top Pin No.8
Combined master and bottom pin length 2-3 = Hollow Top Pin No.7
Combined master and bottom pin length 4 = Hollow Top Pin No.6
Combined master and bottom pin length 5-6 = Hollow Top Pin No.5
Combined master and bottom pin length 7 = Hollow Top Pin No.4
Combined master and bottom pin length 8-9 = Hollow Top Pin No.3
Note: CCT18067PCN Hollow Top Pin Spring must be used with 670 and LIW cylinders.

Key

Key Cutting Machines
ASSA ABLOY recommends that all Lockwood GEN6TX® Keys are cut to code rather than on duplicating machines.
If cutting on Silca Uno Code use card 405.

LOCKWOOD-GEN6TX-Keying-System-FIG-12

Key Inserts
GEN6TX® Key inserts come in 12 colours to choose from.
All items are PTO.

LOCKWOOD-GEN6TX-Keying-System-FIG-13

Barrels

  • To create your Barrel replace ### with the desired profile.
  • All Gen6TX® barrels are supplied with construction holes by default where applicable.

001
Part Number: BG6TX001###SC
For use with:

  • 001 Deadlatch internal Cylinder
  • Nexion Cylinders
  • Onyx internal Cylinder
  • 680 Cylinder
  • 900 Macquarie internal Cylinder
  • W75 Whitco Deadlatch Internal Cylinder

Note:

  • 001 with Safety Release & 001 with Safety Release & Lock Alert.
  • 680 rounded body with oval screw hole plug cover.

LOCKWOOD-GEN6TX-Keying-System-FIG-14

201
Part Number: BG6TX201###SC
For use with:

  • 001 & 002 Deadlatch external Cylinder
  • 100 & 201 Nightlatch external Cylinder
  • 355 & 303 external Cylinder
  • 200 & 211 Stream Latch external Cylinder
  • 213 Stream Lock Deadbolt external Cylinder
  • 507 Nightlatch external Cylinder
  • 900 Macquarie external Cylinder

Note:

  • Lockwood rim locks come standard with 5 5-pin rim Cylinder. A new 6-pin Cylinder housing will be required to use this barrel.

LOCKWOOD-GEN6TX-Keying-System-FIG-15

530
Part Number: BG6TX530###SC
For use with:

  • 530 Cylinders for 530/930/950 Series Locksets
  • 234 Padlocks (early removable core model ~Year 2000)
  • Durabolt

LOCKWOOD-GEN6TX-Keying-System-FIG-16

To create your Barrel replace ### with the desired profile.

570
Part Number: BG6TX570###SC
For use with:

  • Selector Series Mortice Lock
  • Synergy Series Mortice Lock
  • Pentagon Series Mortice Lock
  • 007 & 008 Deadbolt Cylinders
  • 334 Padlock
  • 355 internal Cylinder
  • 500 Series Lockset Cylinders
  • 570E Modular Base Cylinder
  • 590 Short back set Mortice Lock
  • 693 Cupboard lock (691 Cylinder)
  • 777 Deadbolt Cylinders
  • 3540 Series Mortice Lock
  • 8217-5 Astra oval Cylinder
  • 8217-6 Astra round Cylinder
  • 8217-7 Astra flat sided Cylinder
  • Airlock Cylinder
  • LIW Lock-it-Well Cylinder
  • Cortex (Mortice Lock version)

LOCKWOOD-GEN6TX-Keying-System-FIG-17

670
Part Number: BG6TX670###SC
For use with:

  • 670 Cam Lock

Note:

  • Requires use of hollow top pins & hollow top pin springs.

LOCKWOOD-GEN6TX-Keying-System-FIG-18

3570
Part Number: BG6TX3570###SC
For use with:

  • Synergy Series Mortice Lock Hold Back Cylinder

Note:

  • Must be used with 3570 Cylinder housing.
  • Cam screw pitching is different to a standard 570 barrel. Only the two-piece hold-back cam assembly is suitable for this barrel.

LOCKWOOD-GEN6TX-Keying-System-FIG-19

To create your Barrel replace ### with the desired profile.

7115
Part Number: BG6TX7115###SC
For use with:

  • Symmetry Cavity Slider Cylinder
  • Whitco Blaxland Cylinders

Note:

  • This barrel is used with the standard 5-pin. Cylinder housing and the first chamber is not used. Only chambers 2-6 can be used.

LOCKWOOD-GEN6TX-Keying-System-FIG-20

8218
Part Number: BG6TX8218###SC
For use with:

  • 8218 Metal Craft threaded Cylinder
  • 8219 Yale threaded Cylinder
  • 8466 Kawneer threaded Cylinder

LOCKWOOD-GEN6TX-Keying-System-FIG-21

8221
Part Number: BG6TX8221###SC
For use with:

  • “PD” type Cylinders
  • Onyx external Cylinder
  • Symmetry 7105 & 7108 Deadbolt Cylinders
  • Yale YK16 Series Knob Sets
  • Yale YL17 Series Lever Sets
  • Yale YDB1 Deadbolt Cylinders

Note:

  • When keying the Onyx to 6 pins, a new 6-pin housing is required

LOCKWOOD-GEN6TX-Keying-System-FIG-22

To create your Barrel replace ### with the desired profile.

8474
Part Number: BG6TX8474###CP
For use with:

  • 8474 Garage L Handle Lock

LOCKWOOD-GEN6TX-Keying-System-FIG-23

9555-1
Part Number: BG6TX95551###CP
For use with:

  • 9555 Euro double cylinder fixed cam

LOCKWOOD-GEN6TX-Keying-System-FIG-24

9555-2
Part Number: BG6TX95552###CP
For use with:

  • 9555 Euro cylinder and turn fixed cam

LOCKWOOD-GEN6TX-Keying-System-FIG-25

9555-3
Part Number: BG6TX95553###CP
For use with:

  • 9555 Euro double cylinder lazy cam
  • 9555 Euro cylinder and turn lazy cam
  • 9555 Euro single cylinder fixed cam
  • 9555 Euro single cylinder lazy cam

LOCKWOOD-GEN6TX-Keying-System-FIG-26

Ordering Table

To create your Barrel replace ### with the desired profile.

Cylinder & Barrel Table

LOCKWOOD-GEN6TX-Keying-System-FIG-27

Maintenance

Lubrication
ASSA ABLOY recommends using Inox MX3 lubricant.

  • Spray the lubricant down the barrel keyway after assembly while holding the cylinder upside down.
  • Operate the cylinder three times to spread the lubricant and wipe the cylinder clean of excess lubricant.

Never paint over cylinders.

Coding

Coding
A ProMaster module has been developed with WH Software to assist with coding GEN6T Key Systems. The module incorporates the rules in this section and allows for flexibility around other recommendations.

Guidelines

  • GEN6T uses both Lockwood Inline Pins 0-9 and Lockwood T Pins 1-9.
  • Use of a pin deeper than 7 in the first chamber is not recommended.
  • T Pins can be used in chamber positions 1-6.
  • T Pin’s can be used in either direction, ASSA ABLOY recommends H.
  • T Pin direction is specified as indicated in the diagram below, either H or T.

LOCKWOOD-GEN6TX-Keying-System-FIG-28

Rules

  • A minimum of one T Pin must be used in any GEN6T cylinder.
  • MAC’s rule between standard cuts is 7.
  • MAC’s rules for T Pin cuts are calculated as described in the diagrams and table to the right.
From Direction To MAC’s
Standard Cut Down to Low High 7
Standard Cut Up to Low High 7
Standard Cut Down to High Low 8
Standard Cut Up to High Low 6
High Low Down to Low High 6
Low High Down to Low High 5
High Low Up to Low High 6
Low High Up to Low High 7
High Low Down to High Low 7
Low High Down to High Low 6
High Low Up to High Low 5
Low High Up to High Low 6

NOTE: Standard cut depths from #0 to #9 T-pin cut depths from #1 to #9

GEN6T Coding

LOCKWOOD-GEN6TX-Keying-System-FIG-30 LOCKWOOD-
GEN6TX-Keying-System-FIG-31

When it comes to safety it’s primal, it’s our survival, a basic human need. We want freedom to live, explore and rest without fear. To leave behind in safety our precious, cherished and most valuable things. And to come back to them exactly as we left them.
For as long as we have valuables, we will always need protection. Though the need for our products is driven by concerns, the Belief in our Brand is propelled by confidence. An unquestioned confidence in our ability to protect what is most important to you. Our products provide peace of mind through strength, substance and style. Our reputation is forged in traditions, supreme workmanship, uncompromised values and above all our people. We are a trusted, tireless and vigilant guardian that protects families, households, trades and businesses.
Because if feeling safe is a basic human need, knowing you’re safe is why Lockwood exists. For over 75 years, our guiding principle has been and will always be: To take the worry out of protecting what is valuable to you.
Lockwood: no worries®

Lockwood is the leading brand in the Australian locking industry. With an established reputation for high-quality products, this iconic brand provides a wide range of locking solutions to residential housing, commercial building and industrial application markets. Lockwood is supported by an extensive distribution and aftersales support network. Our customers include retailers, architects, trade and industrial personnel, locksmiths and security dealers.

ASSA ABLOY is the global leader in door-opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. ASSA ABLOY is represented in all major regions, in both mature and emerging markets, with leading positions in Australia, Europe and North America.

Warranty

The Lockwood 25-Year Mechanical Warranty Our belief that we manufacture the finest premium products available in today’s marketplace is backed by the Lockwood 25-Year Mechanical Warranty, ensuring that Lockwood continues to keep Australians safe by delivering security and peace of mind. For warranty terms and conditions, please visit www.lockweb.com.au or call 1300WARRANTY

CONTACT

  • ASSA ABLOY Australia Pty Ltd
  • 235 Huntingdale Road
  • Oakleigh, Victoria, 3166
  • Australia
  • 1300 LOCK UP (1300 562 587)
  • lockweb.com.au
  • ASSA ABLOY New Zealand Ltd
  • 6 Armstrong Road
  • Albany, Auckland, 0632
  • New Zealand
  • nzsales@assaabloy.com
  • Telephone +64 9415 7111
  • assaabloy.com/nz

Disclaimer

Whilst every effort has been made to ensure that the information contained in this manual is accurate at the time of publication, ASSA ABLOY Australia Pty Limited (“ASSA ABLOY”) recommends that you consult ASSA ABLOY or its agents before placing an order to ascertain current information on specific products, as ASSA ABLOY reserves the right to make changes without notice. ASSA ABLOY will not be liable for any injury, loss or damage whatsoever, arising from any errors or omissions in the information contained in the manual or arising from the use or application of the information contained herein.
© 2023 copyright by ASSA ABLOY All rights reserved

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals