LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture Installation Guide

: June 4, 2024
: LOCKWOOD

Table of Contents

LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture
Pack Contents
INSTALLATION INSTRUCTION
- Lock Operation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture

LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture PRODUCT-
IMG

Application: Provides secure deadlocking for aluminum hinged doors. Palladium Xtra furniture available with daylatch snib.

Tools Required:

Drill
3.2mm Drill Bit
10.0mm Drill Bit
20.0mm Drill Bit
Phillips Screwdriver #2
Square Screwdriver #1

Pack Contents

$LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture FIG $1$$ $LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture FIG $2$$

Screw Selection:

Screw	Stile Width
M4 x 49mm	38 – 43mm
M4 x 55mm	43 – 49mm
M4 x 60mm	46 – 55mm
M4 x 65mm	55 – 58mm

INSTALLATION INSTRUCTION

Door Preparation $LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture FIG $4$$
Route the door as shown in the routing diagram.
Note : For Palladium Xtra Furniture, see separate instructions.

Setting Deadbolt Projection

Before fixing the lock into the stile, select the correct deadbolt throw.
To restrict the throw to 13mm select S
To restrict the throw to 24mm select L
Ensure the arrow is pointing to the desired throw application

Note: When lock has 13mm projection selected the key must be rotated once deadlock. When lock has 24mm projection selected the key must be rotated twice to deadlock.

Fixing Lock

Place the lock assembly into the stile
Fix the lock onto the stile using the two 8g x 7.5 screws

Fixing Furniture and Cylinder

Insert the drive bar (spindle) through the square drive hole in the lock
Place the furniture onto the drive bar. For security, ensure the interior handle is on the inside of the house
Place the cylinder through the cylinder hole
Fix cylinder using the supplied M5 cylinder fixing screw as supplied
Fix together the furniture using the two M4 furniture fixing screws. See screw selection chart to determine correct screw length

Note: If fixing Palladium Xtra Furniture with daylatch snib, refer to separate Palladium Xtra Furniture instructions enclosed.

Latch Reversal $LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture FIG $8$$

Undo the M4 latch screw
Reverse the latch as desired
Refasten the M4 latch screw to secure the latch
Insert the latch wear pad

Note: 2mm Latch Packer is provided to allow for latch projection adjustment. An additional 2mm packer is available for purchase

Lock Operation

$LOCKWOOD Induro 2 Point Mortice Lock Palladium Furniture FIG $9$$

Deadlocking Operation

Pull the door shut. The door will self-latch
Turn the key towards the edge of the door to deadlock
Note: For 13mm, turn the key once only For 24mm, turn the key twice
The door is now secure from exterior and interior

Opening Operation

Turn the key away from the door edge to deactivate the deadlock
Note: For short throw, turn the key once only For long throw, turn the key twice
Retract the latch

Troubleshooting

Do I need to tap holes?| No. All screws are self tapping.
The furniture screws do not tighten| Ensure the screws line up with the screw boss on the exterior handle.
Do I have to use the supplied screws?| For best performance, it is recommended that only the supplied screws are used.
The key function does not operate| Ensure the motion of the latch is not restricted.
Can not achieve 24mm deadbolt throw| Ensure the locks deadlock is set to ‘L’. Turn key twice.

ASSA ABLOY New Zealand Limited 6 Armstrong Road, Albany, Auckland 0632 nzsales@assaabloy.com www.assaabloy.co.nz
ASSA ABLOY Australia Pty Limited 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 ©2019 1300 LOCK UP
www.assaabloy.com.au