BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop Installation Guide

May 15, 2024
BENCHDOG TOOLS

BENCHDOG TOOLS logo MK3 RAIL SQUARE ULTRA REPEAT STOP
SET UP INSTRUCTIONS

MK3 Rail Square ULTRA Repeat Stop

BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig

BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
1TAKE THE MK3 REPEAT STOP AND LOCATE THE LONG SLOTS WITH THE FLAT SIDE OF THE EXTRUSION FACING DOWN.| BENCHDOG TOOLS
MK3 Rail Square ULTRA Repeat Stop - Fig 2LOCATE THE RS (REPEAT STOP) HOLES
---|---
BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
3LINE UP THE REPEAT STOP SLOTS TO THE RS HOLES ON THE RAIL SQUARE| BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop -
Fig 4TAKE THE SUPPLIED THUMBSCREWS WITH THE PLASTIC WASHERS.
BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
5SCREW DOWN THE REPEAT STOP BUT DON’T FULLY TIGHTEN.| BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
6SLIDE ON YOUR FLAGSTOP AND TIGHTEN DOWN THE THUMBSCEW AT YOUR CHOSEN LENGTH (WE HAVE SET IT AT 30MM)
BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
7USING A RULER OR TAPE MEASURE, SLIDE IT UNDER YOUR TRACK AND BUTT IT UP TO THE FLAGSTOP.| SLIDE THE REPEAT STOP TOWARDS THE TRACK AND CHECK THAT THE MEASUREMENT IS READING THE SAME MEASUREMENT ON THE RULER / TAPE MEASURE.
BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
9TIGHTEN UP THE THUMBSCREWS ONCE THE MEASUREMENT HAS BEEN SET.| ![BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop

  • Fig 10](https://manuals.plus/wp-content/uploads/2024/03/BENCHDOG-TOOLS-MK3 -Rail-Square-ULTRA-Repeat-Stop-Fig-10.jpg)UNSCREW THE T-NUT SO IT IS TO THE TIP OF THE SCREW.
    BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - Fig
11THEN SLIDE THE CALIBRATION SCREW WITH THE ATTACHED T-NUT INTO THE REPEAT STOP ON THE UNDERSIDE.| BENCHDOG TOOLS MK3
Rail Square ULTRA Repeat Stop - Fig 12SLIDE THIS UP TO THE RAIL SQUARE AND USING THE 3MM HEX KEY TIGHTEN THIS UP AND THAT IS NOW CALIBRATED.

REPEAT STOP EXTENTION

BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop - EXTENTION
1

FOR EXTENDING YOUR REPEAT STOP YOU WILL NEED THE FENCE JOINER TO JOIN THE TWO HALVES TOGETHER.
START BY HAVING THE FLAT PART OF THE REPEAT STOP FACING YOU. SLOT THE FENCE JOINER IN ONE SIDE OF THE REPEAT STOP FOLLOWED BY THE OTHER SIDE. PUSH THE TWO HALVES TOGETHER UNTIL THEY MEET. THEN SECURE BY TIGHTENING UP THE GRUBSCREWS WITH A 2.5MM HEX KEY.BENCHDOG TOOLS MK3 Rail Square ULTRA Repeat Stop -
EXTENTION 2TAKING THE CONNECTOR BLOCK, YOU CAN SLIDE THIS ONTO THE EDGE, MAKING SURE ITS RIGHT IN THE MIDDLE OF THE JOIN.
USING A 2MM HEX KEY YOU CAN TIGHTEN UP THE GRUBSCREWS AND THIS IS NOW SECURLY FIXED INTO PLACE.

FOR MORE INFORMATION PLEASE VISIT
CONTACT@BENCHDOGS.CO.UK
WWW.BENCHDOGS.CO.UK

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals