AMX VARIA-ACS-810A 8 Inch and 10.1” Angle Select Tabletop Stand User Guide

AMX VARIA-ACS-810A 8 Inch and 10.1” Angle Select Tabletop Stand

Product Information

Specifications

• Model: VARIA-ACS-810A, VARIA-ACS-150A
• Compatibility: VARIA-80, VARIA-100, VARIA-100N, VARIA-150, VARIA-150N Touch Panels
• Angle Options: Three selectable angles
• Installation Method: Screwdriver required

Product Usage Instructions

Installation

1. Place the touch panel face-down on a soft cloth.
2. Remove any screws from the lower cover if installed.
3. Push the lower cover away from you by placing your thumbs on the rectangular access holes.
4. Route the networking cable through the base and plug the RJ-45 connector into the touch panel.
5. Reinstall the lower cover ensuring the cable routes out the bottom.
6. Screw the mount to the rear of the touch panel.
7. Select the desired angle for installation and insert the base into position.
8. Lock the base in place by installing the supplied set screw.

Removal
To remove the panel, follow the installation steps in reverse order.

Frequently Asked Questions (FAQ)

• Q: Can I use this tabletop stand with other touch panel models?
  A: The VARIA-ACS-810A and VARIA-ACS-150A stands are compatible with specific touch panel models mentioned in the user manual. Using them with other models may not provide optimal functionality.

• Q: Do I need any additional tools for installation?
  A: Installation requires a Philips-head screwdriver which is not included in the package. Ensure you have one available before starting the installation process.

Overview

The Varia Angle-Select Tabletop stands are designed for 8” VARIA-80, 10.1” VARIA-100, & 15.6” VARIA-150 Touch Panels, and give them a sleek & modern tabletop solution that can be installed at one of three angles to best suit the users’ needs.

Model Availability & Compatibility

ANGLE-SELECT TABLETOP STANDS

VARIA-ACS-810A (AMX-UMT8111)| VARIA-80 Touch Panel (AMX-UTP0811) VARIA-100 Touch Panel (AMX-UTP1011) VARIA-100N Touch Panel (AMX-UTP1011N)
VARIA-ACS-150A (AMX-UMT1511)| VARIA-150 Touch Panel (AMX-UTP1511) VARIA-150N Touch Panel (AMX-UTP1511N)

Other Models Available

FIXED TABLETOP STANDS

VARIA-ACS-80F (AMX-UMT0801)| VARIA-80 Touch Panel (AMX-UTP0811)
VARIA-ACS-100F (AMX-UMT1001)| VARIA-100 Touch Panel (AMX-UTP1011) VARIA-100N Touch Panel (AMX-UTP1011N)

Installation

Varia Fixed Tabletop Stands are easily installed with the supplied hardware and a Philips-head screwdriver.

1. Place the panel face-down on a soft cloth and arrange the panel so that the top of the touch panel is closest to you.

2. If they are installed, remove two small screws from the lower cover.

3. Place your thumbs on the rectangular access holes, and push the lower cover away from you. Do not discard, this will be reinstalled later.

4. Rotate the panel back around so the bottom is closest to you.

5. Route the networking cable through the base first, and then plug the RJ-45 connector into the back of the touch panel.

6. Reinstall the lower cover, first snapping it into place. Optionally, two small screws supplied in the hardware accessory bag may be installed. Make sure the cable routes out the bottom of the lower cover.

7. Screw the mount to the rear of the panel using the supplied screws.
   NOTE: The three slots should be oriented UP and the set screw holes should be oriented DOWN.

8. Select the best angle for installation. The Angle-Select Tabletop Stand can be installed at one of three (3) angles:

   • a. Upright 60° angle
   • b. Mid 45° angle
   • c. Low 30° angle

9. Insert the base into the desired position. Insert the tab first and set flat against the mount.

10. Install the supplied set screw to lock the base in the desired position.

Removing

To remove the panel, follow the installation directions in reverse.

© 2023 HARMAN. All rights reserved. SmartScale, NetLink, Enova, AMX, AV FOR AN IT WORLD, and HARMAN, and their respective logos are registered trademarks of HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time. The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082
AMX.com
800.222.0193
469.624.8000
+1.469.624.7400
fax 469.624.7153

References

• AMX Audio Video Control Systems | English (US)
• AMX Audio Video Control Systems | English (US)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>