FEDOUR 100W Mini Aquarium Heater Instruction Manual

FEDOUR 100W Mini Aquarium Heater

 **Instruction Manual**

Instruction

Please be sure to read this manual carefully, understand and follow the instructions to install and use this product correctly, so as to avoid safety accidents, electrical failures and fires caused by incorrect operation.

Features

1. Built-in water level sensing device , can automatically cut off the power when the heater is out of water, making the heater safer to use.
2. Built-in multiple temperature sensors, adopt MCU electronic calculation management, can accurately and reliably control the temperature. It will automatically cut off the power when it detects over-heating.
3. External temperature setting button , can adjust the set temperature cyclically within 69-95°F (18-35°C ). LED electronic water temperature display, easy to operate.
4. Adopt heat-resistant plastic shell , all-round protection design , suitable for fresh water and sea water.
5. Mini size, with three powerful suction cups , easy and reliable installation .

Cautions

1. Before use, please confirm whether the power supply voltage is consistent with the standard voltage of the product.
2. Before or during the use of the product, if the power cord is damaged or burnt , it must be stopped using immediately and should be discarded or returned to the seller.
3. If there are abnormal noises , odors or smoke during the use of the product, it must be stopped using immediately and should be discarded or returned to the seller.
4. This product must be completely immersed in water for use!! !
5. This product is only suitable for indoor fish tanks use, and cannot be used outdoors.
6. There are fragile parts inside this product. Please handle with care during use and installation , and avoid rough operation. Do not allow children under 18 years old to operate or use it as a plaything .
7. When you need to remove the heater from the fish tank or move the heater position in the water, please must cut off the heater power 10 minutes in advance , and wait until the heater cools down before you operate it, otherwise scalds or product damage may occur.
8. The temperature setting button does not have a waterproof design. If it accidentally falls into the water or gets splashed with water, please must stop using it; this heater comes with a temperature control function , please do not connect to other temperature control devices to use, which may cause product failures.
9. When the heater fixed in the fish tank needs to be taken out, you should separate the suction cup to
   take out the heater as a whole. You cannot pull the wire directly to force it out.

Installation and Use

1. As shown in(Diagram 3), use the suction cups to correctly fix the heater in the proper position of the aquarium(Please do not bury the product in the filter material or sand of the fish tank). The heater needs to be placed in a place with good water circulation (such as around a water pump) to ensure uniform heat in the fish tank.
2. In order to prevent the water of aquarium from flowing back to the controller or power sockets along the wires, the power socket should be higher than the water surface of the aquarium ; Or make a bend at the front of the controller as shown in(Diagram 2).
3. Plug in the power supply, the power indicator is on , and the number displays the current temperature (When it is detected that the current temperature is lower than the set temperature , the heater will start working and the heating indicator is on ; When the current temperature is higher than the set temperature, the heating indicator will be off).
4. Temperature setting: simply press the “SET” button shown in(Diagram 1 ), and the number starts to flash , indicating that it has entered the temperature setting state. The set temperature is cycled at 69-95·f. When it reaches the set temperature you want, just stop pressing , the number stops flashing and turn to show the current temperature , it means the temperature-setting is completed. The final flashing number is what you set(Please note if you want to check the temp you set, you need to press the button again , it will show you by flashing) . And the heater will remember what you set, you don’t need to set it again if the power cut off and connect again.
5. This heater has a built-in water level sensing device. If the heater leaves the water surface, the digital display is “E1”.
6. When the actual current temperature is higher than 93°F (34°C) or 6 degrees higher than the set temperature , the heater will automatically start the over-heating protection function . The heater will stop heating and display “E2”. At this situation , you must cut off the power, wait 3 seconds , and then plug it in. If the “E2” display appears again , you must find out the reason and lower the temperature of the aquarium before use.

Diagram 3

Cleaning and Maintenance

1. After the heater is used for a period of time , scale will adhere to the heating part. It is recommended to clean it properly, otherwise the heating effect will be reduced and the heat cannot be dissipated in time , resulting in damage to the heater.
2. For the structure of this heater, it is recommended to use white vinegar or baking soda , soak in water until the scale falls off, and wash it well (Do not remove the shell nor use a sharp tool to scrape off the scale).

If you have any questions during use, or any problems with the product you received, please
contact us by below E-mails. We will serve you within 24 hours.
E-mail: aquaservice@163.com
aquaservice@yeah.net
Manufacturer: Zhongshan I bay Electric Appliance Co., Ltd
Manufacturer Address: 3rd, No.6 Shun min Road, Jixi Xiaolan
Town, Zhongshan, Guangdong, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>