Musicca XHY-JZG01 Virtual Drum Kit Instruction Manual
- June 14, 2024
- Musicca
Table of Contents
Musicca XHY-JZG01 Virtual Drum Kit
Product Information
Specifications
- Compliance: Part 15 of the FCC Rules
- Radiation exposure limits: FCC compliant for uncontrolled environment
- Minimum distance between radiator and body: 0cm
Product show
- A. Air drum sticks
- A1. Power switch
- Long press: turn on/ off
- Click: fix the drum position (the power button of the two sticks)
- A2. Indicated light
- Working: the light rolling
- Sufficient Charge: light flashing red yellow light flash alternately -factory mode calibration
- А3: Type-C charger
- A4: Charge indicate light
- Red light on: charging
- Red light off: charging finish
- B. Pedal (HI-HAT, BASS DRUM)
- B1. Power switch
- Long press: turn on / off
- B2. indicate light
- Blue light on: working
- Blue light turn red: low battery
- Red light off: charging finish
- Red light flash slowly: low battely
- Red light on: charging
- B3. Type-C charger
- C. Audio adapter
- C1. Power switch
- Long press: turn on /off
- C2. 3.5 Audio interface connect to speaker or earphone
- C3. type-C charger
- C4. Indicate light
- Blue light flashing: working
- Red light on: charging
- Red light off: finish charging
- Red light flash slowly: low battery
- D. Karaoke speaker
- D1.: Microphone power switch
- D2.: Microphone voice”+’
- D3.: Microphone voice”+’
- D4.: Microphone change voice model
- D5.: Mircophone indicate light
- D6.: Speaker voice “+”,double click
- D7.: Speak voice “-“, double click
- D8.: Turn on speaker or Pause speaker
- D9.: light model
- D10.: Blue tooth/AU model change ( please change into AUX model when connect the drum)
Product Portfolio Introduction
Means include this device X means not include.
Operating instruction
Turn on for connection
- Please fix HI-HAT/BASS DRUM on the left /right shoes and press the power 3 seconds. ( some style don’t have the pedal).
- Use Audio adapter to connect the speaker( speak need has AUX connector ), and turn on. If has the Karaoke , press M convert into AUX model , if using 3.5 wired earphone can insert the Audio adapter directly.
- Put the sticks to the virtual drum position, Long press the power switch to start the stick, then press one time again, release your fingers then finish fixing the position.
- Connect the phone accompanying music (can ignore this )Connect blue tooth BT-Air drum ,Play the music; play the drum sticks, if you have the karaoke set, can sing, achieve entertainment sharing (Remark: All the above devices’ blue lights from flashing to stabilization means turn on, if the red light flashing means the devices are low battery, please charing them.
Device Calibration
- When your position changed, please press the switch button of the sticks, see the No.2 area light flashing, try to drub the sticks to make sure the drum is on your position.
- Sensor calibration device reset (please do it carefully)When you restart the sticks or change your position, you need to press the power button to track the sensor of the sticks. If you find the bottom drum status is not correct, need to press the power button shortly to recalibrate. if it is still not correct after Sensor initialization, need to clear the save date of the sensor and reset the sensor through factory calibration model.
How to initialize calibrate the sensor of the sticks
- Fast short press power button 6 times till the yellow light flashing.
- Please put the sticks on a level quiet table, make sure no any other shake , till the indicate light from yellow to pink light flashing.
- Take the sticks, draw ” ” in the air , indicator of stick from pink flashing light to cyan light steady on .(or blue light flashing ).
- Finish the initialize calibration . Below is the reference picture of drawing” ∞ “.
Skill Specification
- sticks drub the corresponding position send the homologous voice. Drum sticks face to the horizontal side drub the 2 crash cymbals, 2 Tom-Tom drum, sticks tilted 30 degrees to the level drub the ride cymbals, Floor Tom, snare drum; The area show is below ( Can practice the direction firstly).
- HI-HAT AND BASS DRUM need pedal to control up and down as one time. Please pay attention to the left and right feet (HI-HAT is left, Bass Drum is right).
Important Notes
- Don’ tuse the sticks to drub hard things.
- If the drum position is not correct, please reset the position.
- When the red light flashing please charge for the device.
- If has many device in one place ,please match one by one, not mix.
- If the sticks or pedals’ blue light flashing ,it means it haven’ t connected to the speaker or Audio converter, please connect again.
- The pedals need to calibrate before using , please make sure fix them on the correct feet, the pedal will up or down according to your fee.
Equipment parameters
FCC Warnning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.