kami YKS0223 2K Pan Tilt Camera Installation Guide
- May 15, 2024
- Kami
Table of Contents
kami YKS0223 2K Pan Tilt Camera
Product Information
Specifications
- Compliance: FCC radiation exposure limits
- Environment: Uncontrolled
- Minimum Distance: 20cm between radiator and body
Product Usage Instructions
Installation
- Ensure the equipment is installed in a location where there is a minimum distance of 20cm between the radiator and the body.
Operation
- Operate the equipment with the recommended minimum distance of 20cm between the radiator and your body at all times.
Maintenance
- Regularly check the equipment to ensure the specified minimum distance is maintained during operation.
FAQ
Q: What happens if the minimum distance requirement is not met during operation?
- A: Failure to maintain the minimum distance between the radiator and your body may result in exceeding FCC radiation exposure limits, which could pose health risks.
What’s in the box
Get to know your camera
Getting started
- Insert the Micro SD card
- Insert the Micro SD card gently on the side edge of the camera.
- Connection Preparation
- Powering the Camera
- Network Connection
* **Option 1:** Ethernet -Use the ethernet port to connect to the internet.
* **Option 2:** WiFi -Use the mobile app to connect the camera to the internet using your WiFi.
* **Note:** Make sure smart phone is connected to your wireless router.
* Please note the camera is only working under 2.4G Wi-Fi, not support SG Wi-Fi.- Camera Setup
- Please refer to the additional Software Setup Guide on how to download and install the application to set up your camera.
- Example: If you are using this camera with KamiCare resident safety and security solution, then you will need to download and install the KamiCare application from the App Store or Google Play Store or use www.kamicare.ai to start using this camera.
Mounting Instructions
- Step 1 Use the provided anchors and screws to mount the wall mount base.
- If the wall is wooden, you can screw the mount directly. ****
- Step 2 Adjust the camera’s view angle to your preferred position.
Troubleshooting
- Press and hold the reset button for over 5 seconds.
- When the reset is successful, the camera will play a confirmation message and the LED will start flashing amber light.
Appendix: Camera LED Guide
| NO. | LED Status | Camera Status |
|---|---|---|
| 1 | Red LED on | System starting up |
| 2 | Red LED blinks quickly | Standby for configuration |
| 3 | Blue LED blinks quickly | Network pairing |
| 4 | Blue LED on | Camera online |
| s | Red and blue LED blinks alternately | OTA upgrade |
FCC COMPLIANCE STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The distance between the user and the products should be no less than 20cm This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.
IC WARNING
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-empty
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device
The distance between a user and the products should be no less than 20cm
- Hereby: Yi Technology Co., Ltd., declares that the radio equipment: YKS.0223 complies with Directive 2014/53/EU.
- ProductType: YKS.0223
- Wi-Fi: 2.4GHz ,802.11 b/g/n
- Max RF power: 17dBm
- Manufacture: Yi Technology Co., Ltd.
- Address: Building 18, NO.55 Chuanhe Road, Pudong New District,
- Shanghai, China
- The full text of the EU Declaration of Conformity is available at the following internet address: https://kamistore.eu/pages/product-certification
Documents / Resources
| kami
YKS0223 2K Pan Tilt
Camera
[pdf] Installation Guide
YKS0223, 2BD5Y-YKS0223, 2BD5YYKS0223, YKS0223 2K Pan Tilt Camera, 2K Pan Tilt
Camera, Tilt Camera, Camera
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>