kami YDS20120 Doorbell Camera Installation Guide
- June 10, 2024
- Kami
Table of Contents
kami YDS20120 Doorbell Camera
What’s in the Box
-
Ka mi Doorbell Camera x 1
-
Wire Nuts x 2
-
Charging Cable x 1
-
Battery x 1
-
Screw Bagx 1
-
Chime Connector x 1
-
Diode x 1
-
Backplate x 3
-
Manual x 1
-
Installation Hardware x 1
-
Extension Wires x 2
-
Screwdriver x 2
Getting to Know Your Doorbell Camera
To reset the doorbell fast press the Reset Button {less than 1 second).
Charge+ Insert battery
a. Charge the Battery
Please charge the battery, using a micro USB cable. and a power adapter (not
included).
The indicator light will be red while charging and turn white when fully
charged.
b. Remove the Protective Cover
Press down on the face of the doorbell with your thumbs and pull the outer
protective cover up and away from the main body, as shown in the diagram on
the left.
c. Installing the Battery
After removing the protective cover, push the battery into the battery
compartment as shown. (Ensure that the battery is inserted in the correct
direction with pins facing up}
Push the tab shown in the diagram below to free the battery. Pull the battery
straight down to R remove.
Pairing Your Doorbell Camera
Step l
Download the Kami Home/ YI Home App and sign up or sign in to your existing
account.
Step2
Ensure that your cell phone is connected to your local Wi-Fi network.
Enable the 11 Location” function on your phone, and then authorize the
“Location” function of the Kami Home/ YI Home App.
Step3
After logging in to your Kami Home/ YI Home App, tap the,.+” symbol in the top
right corner and select “Kami Doorbell Camera11
Wait for the voice prompt and then tap the “I heard ‘Waiting to connect”‘
button.
Step4
Enter your Wi-Fi network password and tap the” Please choose Wi-Fi” button.
A QR code will appear on your phone’s screen.
Point the QR code towards the camera lens until you hear the following voice
prompts “QR code scan is successful connecting to Wi-Fi” and “Wi-Fi is
connected”.
step 5
Tap the “Next” button and wait until you hear the message “Pairing 1s
successful” both from the camera and from the app. Assign your desired name to
the Doorbell and tap “Save”. You will hear “You may start using your camera
now”.
Installation Options
a. Remove the Original Doorbell (optional)
If you are replacing an eisting doorbell, please switch the power off, remove the doorbell, and disconnect the wires.
b. Electronic Doorbell Setup: Installing a Diode ( optional)
- If you want to connect your doorbell to an electronic bell (if your doorbell has a speaker, it uses a digital chime), you will need to install a diode.
- If you are using a mechanical indoor doorbell, DO NOT install a diode, as this wiU damage the existing doorbell.
c. Mechanical Doorbell Setup: Installing the chime connector ( optional)
If you are using a mechanical chime, please install the chime connector ① to
ensure a stable power supply.
If you don’t want chime to make a sound, please connect the wires as shown in
the picture②.
Please make sure the power for the doorbell .is shut down when you do this step.
d. Height and Distance Recommendations
The optimal detection range for the Kami Doorbell Camera is 0-4m / 0-13ft. Additionally, we recommend you install the doorbell at a height of 1.2m / 4ft to ensure the ground in front of your door can be captured.
e. Suggested Installation Angle
Your Kami Doorbell Ca111era co1mes with three different backplates that can be used to help place yoLlr cam,era at Flat Backpl.ate #1.
- If ‘YOU don’t want to change the camera1s angle lJse Flat Backplate #1.
- If you want to angle your Doorbell to the left or right use Horizontal Backplate #2.
- if you want to angle your camera in a vertical direction, use Backplate #3.
f. Fixing the Backplate to the Wall (optional)
Take out the backplane and lay it flat on the wall where Doorbell is to be installed. Take a pen and press it firmly into the center of the two holes in the back pa,nel to mark the wall. Note: Installing your camera on wood doesn•t require screw anchors.
g. Connecting the Doorbell wires and (2) Extension Wires (optional)
You connect each of the wires to either of the screws in the back. The order
does not matter.
If your wires are too short and you have trouble connecting the wires coming
out of the wall to the back of the doorbell, please use the included Extension
Wires and wire nuts. (See Picture) .
Please make sure the power for the doorbell is shut down while you : complete the wiring.
h. Mount the Doorbell to the Flat Backplate
Feed all wires (and wire nuts, if you use them) into the wall and use four screws (screw C) to secure your doorbell to Flat Backplate #1.
Mount the Doorbell to the Flat Backplate:
Flat Backplate #1
Mount the Doorbell to an Angled Backplate:
**Angled Backplate #2 or Backplate #3
**
i. Installthe Front Panel
- Use Screw_A to keep the Doo:rbell Front Panel in p~ace.
- Use Mounting S,crew A to ·fix the ciamera
j. Turning the Power On
To co1mplete the installation proc1ess, please switch the power back ON and test the 01per,ation of yo1ur Doo’rbell.
FCC COMPLIANCE STAT’EMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The distance between user and products should be no less than 20cm
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.,
- Connect the equipment. into an outlet on a circuit different from that to which. the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for .hetp.
Customer Support
FCC . ID: 2AFI MD520120 IC: ,20436-YDS20120
Website: www.kamihome.com
E-mail: support@kamihome.com
https://kamihome.comilegalficc
D201 V2.1
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>