WEIJIA JF8113BT-40W Work Light User Manual
- May 15, 2024
- WEIJIA
Table of Contents
WEIJIA JF8113BT-40W Work Light
Operating instructions
Mobile rechargeable LED floodlight
SAFETY INSTRUCTIONS
-
Carefully read the operating instructions before use.
-
Don’t use the floodlight if it is damaged.
In this case, contact an electrician or refer to the specified service address. -
Never open the device.
-
Do not use the floodlight in potentially explosive atmospheres – danger to life!
-
To charge the batteries, only use a certified USB power supply unit.
-
A destroyed protective cover cannot be replaced. The floodlight has to be disposed of if the protective cover is broken.
Please never look directly into the light.
If the minimum distance is not complied with, illuminated objects may overheat.
Hot surface.
- During the charging process, the product is not IP65-compliant (Dust-tight and protected against water-jets).
TECHNICAL DATA
Power| Bluetooth speaker| Colour temperature| Rechargeable battery| Charging
input| Charging time (2 A charging)| Operating Time| Power bank| IP, IK|
Temperature range
---|---|---|---|---|---|---|---|---|---
40 W| 1x 4 W| 6500 K| Li-Ion 7.4 V /5.0 Ah| 5 V/2 A| ~5 hours| 2.5-12 hours|
5V/1 A| IP65, IK08| -10°C – +45°C
SET-UP/MOUNTNG THE LAMP
Using the multi-level, folding bracket, the tilt angle of the lamp can be
adjusted as needed. The lamp can be hung up on a hook using the bracket.
The lamp can be attached to metallic surfaces by means of the magnetic holder
which, depending on the scope of delivery, is either included or available
separately as an accessory.
For this purpose, simply attach the magnetic holder to the bracket of the
light. Please ensure that the magnetic holder is firmly seated in order to
avoid possible damages caused by the falling light.
OVERVIEW OF THE CONTROL ELEMENTS
Switch for power on/off and dimming:
Pressed once: The floodlight starts with the last light intensity set,
the light intensity can be adjusted in 5 steps by pressing several times.
If the switch is not actuated for more than 5 seconds, the floodlight switches
off when it is actuated again, regardless of the last brightness setting.
Switch to indicate the battery charge:
When the floodlight is switched on, the battery charge is displayed in %.
When the floodlight is switched off, the battery charge can be displayed by
pressing the switch with the battery symbol. It is displayed until the switch
is pressed again.
Switch for Bluetooth connection:
When switched on, the floodlight changes to Bluetooth standby mode.
OVERVIEW
- Charging port type C
- Power bank USB
- Charging cable type A/C
BLUETOOTH SPEAKER
To use the speaker via Bluetooth, press the Bluetooth button with the
Bluetooth symbol on the back of the device: the LED above the Bluetooth button
lights up.
Switch on the Bluetooth function on the smartphone: the floodlight is
displayed under “WORKLIGHT” in the selection list. Now activate WORKLIGHT on
the smartphone: the light emits an acoustic signal “Beep”.
Any music on the smartphone can now be played via the speaker of the
floodlight. The volume is controlled via the smartphone.
To terminate the connection, deactivate “WORKLIGHT” on the smartphone: the
floodlight indicates this by means of an acoustic signal: “Beep”. The
connection can also be terminated by switching off the Bluetooth function via
the Bluetooth switch of the floodlight (without acoustic signal).
CHARGING THE BATTERY
Only charge your battery using the supplied charging cable type A/C.
A port type C is available as charging input. The charging cable can be
plugged into a conventional USB charger at the other end.
Only use a tested USB power source (e.g. charger, computer) with a maximum
output voltage of 5 V:
Connection: USB source – charging cable type A/C (3) – charging port (1).
During charging, the charging indicator flashes, it is illuminated constantly
when the battery is fully charged.
CHARGING EXTERNAL DEVICES VIA USB
The floodlight offers a USB power bank function. An external device like a
smartphone or tablet
can be connected to the USB port (2) and charged. The number of possible
charge cycles depends
on the type of external device and on the charge level of the floodlight’s
battery.
MAINTENANCE
The light source of this lamp cannot be replaced; if the light source has
reached the end of its
service life, the entire lamp has to be replaced.
CLEANING
Do not use solvents, caustic cleaning agents or similar products. Only use a dry or slightly moistened cloth for cleaning.
DISPOSAL
Electronic appliances must not be disposed of in household waste!
The European Directive 2012/19/EC on Waste Electrical and Electronic Equipment
and its implementation on national law stipulate that used electronic
appliances should be collected separately and recycled in an environmentally
friendly manner. For possibilities of disposal of the used appliance, please
contact your local or municipal administration. Incorrect disposal of
batteries is harmful to the environment!
Batteries must not be disposed of in household waste. They might contain toxic heavy metals and shall be subjected to hazardous waste treatment. Dispose of exhausted batteries at your local collection points.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not
expressly approved by the party responsible for compliance. such modifications
could void the user’s authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>