beko HCF61620X Cooker Hood User Manual

May 15, 2024
Beko

Cooker Hood
User manualbeko HCF61620X Cooker Hood 1

HCF61620X Cooker Hood

Please read this user manual first!
Dear Valued Customer,
Thank you for preferring this Beko appliance. We hope that you get the best results from your appliance which has been manufactured with high quality and state-of- the-art technology. For this reason, please read this entire user manual and all other accompanying documents carefully before using the appliance and keep it as a reference for future use. If you handover the appliance to someone else, give the user manual as well. Follow the instructions by paying attention to all the information and warnings in the user manual.
Remember that this user manual may also apply to other models. Differences between models are explicitly described in the manual.
Meanings of the Symbols
Following symbols are used in various sections of this user manual:

| Important information and useful hints about usage.
---|---
| WARNING: Warnings against dangerous situations concerning the security of life and property.
**| Warning for danger of fire.
| Warning for electric shock.
Icon**| Protection class for electric shock.

Important safety and environmental instructions

1.1 General Safety
Important Safety Instructions Read Carefully And Keep For Future Reference This section contains safety instructions that will help protect from risk of fire, electric shock, exposure to leak microwave energy, personal injury or property damage. Failure to follow
these instructions shall void any warranty.

  • Beko products comply with the applicable safety standards; the- refore, in case of any damage on the appliance or power cable, it should be repaired or replaced by the dealer, service center or a specialist and authorized service alike to avoid any danger. Faulty or unqualified repair work may be dangerous and cause risk to the user.

  • This appliance is intended to be used in household and similar applications such as:
    – Staff kitchen areas in shops, offices and other working environments;
    – Farm houses
    – By clients in hotels, and other residential type envi- ronments;
    – Bed and Breakfast type envi- ronments.

  • Operate the appliance for its intended purpose only as described in this manual.

  • The manufacturer cannot be held liable for damages resulting from improper installation or misuse of the product.

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

  • Children shall not be allowed play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

  • The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of your product must be at least 65 cm.

  • If the instructions for installation for the gas hob specify a grea- ter distance, this has to be taken into account.

  • Make sure that your mains power supply complies with the information supplied on the rating plate of the appliance.

  •  Never use the appliance if the power cable or the appliance it- self is damaged.

  •  Prevent damage to the power cable by not squeezing, bending, or rubbing it on sharp edges. Keep the power cable away from hot surfaces and naked flame.

  •  Use the appliance with a grounded outlet only.
    WARNING: Do not connect the appliance to the mains until the installation is fully complete.

  • Place the appliance in a way so that the plug is always acces- sible.

  • Do not touch the lamps if they have operated for a long time.
    They can burn your hands since they will be hot.

  • Follow the regulations set out by competent authorities on discharge of the exhaust air (this warning is not applicable for use without flue).

  • Operate your appliance after putting a pot, pan etc. on the hob. Otherwise, high heat may cause deformation in some parts of your product.

  • Turn off the hob before taking the pot, pan etc. from it.

  • Do not leave hot on the hob. Pans with hot may cause self combustion.

  • Pay attention to your curtains and covers since may catch fire while cooking food such as fries.

  • Grease filter must be cleaned at least monthly. Carbon filter must be replaced at least every 3 months.

  • Product shall be cleaned accordance with user manual. If cleaning was not carried out in accordance with user manual, there may be fire risk.

  • Do not use non-fire-resistant filtering materials instead of the current filter.

  • Only use the original parts orparts recommended by the ma- nufacturer.

  • Do not operate the product without the filter and do not remove the fil- ters while the product is running.

  • In the event of be started any flame, de-energize your product and cooking appliances.

  • In the event of be started any flame, cover the flame and neveruse water to extinguish.

  • Unplug the appliance before each cleaning and when the appliance is not in use.

  • The negative pressure in the environment should not exceed 4 Pa (4×10 bar) while the hood for electric hob and appliances running on another type of energy but electricity operate simultaneously.

  • In the environment where the appliance is being used, the exhaust of devices running on fuel or gas, such as room heater must be absolutely isolated ordevice must be hermetical type.

  • When connecting the flue, use pipes with a diameter of 120 or 150 mm. Pipe connection must be as short as possible and have as few elbows as possible.

  •  Danger of choking! Keep all the packaging materials away from children.

CAUTION: Accessible parts may become hot when used with cooking appliances.

  • The product outlet must not be connected to air channels that include other smoke.
  • The ventilation in the room may be insufficient when the hood for electric hob is used simultaneously with the devices operating on gas or other fuels (this may not apply to appliances that only discharge the air back into the room).
  • Objects placed on the product may fall. Do not place any objects on the product.
  • Do not flambe under the your product.

WARNING: Before installing the Hood, remove the protective films.

  • Never leave high naked flamesunder the hood when it is in operation
  • Deep fat fryers must be continuously monitored during use: overheated can burst into flames.

1.2 Compliance with the WEEE
Directive and Disposing of the Waste Product: This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).
This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to offical collection point for recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was puchased. Each household performs important role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.
1.3 Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.
1.4 Package Information
**** Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispo- se of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

General appearance

2.1 Overviewbeko HCF61620X Cooker Hood - Overview

  1. Chimney
  2. Glass
  3. Control panel
  4. Grease filter
  5. Lighting

2.2 Technical data

Model HCF 61620 X HCF 91620 X HCG 61620 X
Supply voltage 220-240V — 50 Hz
Lamp power 2×2,5 W
Motor power 250 W 140 W
Air Flow — 3. Level 603 m3/h
Insulation Class of Motor Class F
Insulation Class Class II

Using the appliance

3.1 Controls panel

| symbol| State
---|---|---
a| | on/off level 1|
b| 2| level 2|
c| 3| level 3|
d| | lamp

Use the high suction speed in cases of concentrated kitchen vapours. It is recommended that the cooker hood suction is switched on for 5 minutes prior to cooking and to leave in operation during cooking and for another 15 minutes approximately after terminating cooking.

  • The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
  • Never use the hood for purposes other than for which it has been designed.
  • Never leave high naked flames under the hood when it is in operation.
  • Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
  • Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

3.2 Efficient use in terms of energy saving

  • When using your appliance, adjust the speed settings according to vapour and odour intensity, in order to save energy.
  • Use low speeds (1-2) under normal conditions, and high speed (3) and boost mode for intense odour and vapour.
  • The hood is equipped with lamps in order to illu- minate the cooking area.
  • Using them for environmental lighting shall cause unnecessary energy expenditure and insufficient lighting.
  • For your device to consume less energy, run it at a low speed level.
  • Your device will reduce energy consumption as it will run more efficiently when you provide sufficient air intake to it.
  • Set your device to the intense suction power level before the formation of steam, in cases where you know that the dense steam will occur. So, you reduce energy consumption by using your device for a shorter time as it will have a sufficient air intake.
  • Keep the lids of the cookware closed to reduce the steam evolving.

3.3 Operating the Hood

  • Hood is equipped with a motor having various speed settings.
  • For a better performance, we advise you to use low speeds in normal conditions, and high speeds when smell and vapors are intensified.
  • You can start the hood by pressing the desired speed level key.(1, 2, 3)
  • You can illuminate the cooking area by pressing the light key.

3.4 Lamp replacement

| • Before replacing the light bulbs, disconnect the power supply of the hood.
• Do not touch the light bulbs when they are hot.
• Be careful not to touch the replaced light bulb directly with hands.
---|---

You may procure lamps from Authorised Service Agents.beko HCF61620X Cooker
Hood - appliance

  1. Using a flat head screwdriver or equivalent tool, carefully pry loose the light cover.
  2. Remove the damaged light and replace with a new one.
  3. Reinstall the light cover. (it will snap shut).
  4. If the lights do not work, make sure that the lamps are fitted properly into their housings before you call for technical assistance.

Lamp|
---|---
Bulb power|  2,1 W
Holder/Socket| ZIK7
Bulb voltage| 3 V
ILCOS Code| GB/T 21656-2016
Size| D67x19,6 mm
Luminous flux| 296 lm
Correlated colour
temperature| 3500 K

This product contains a light source of energy efficiency class “E”.
3.5 Operation with flue connection

  • Vapour is extracted through the flue duct, which is fastened to the connection head on the hood.
  • The diameter of the flue duct must be the same as the connection ring. In horizontal settings, the pipe has to have a slight upward slope (around 10º) so that the air can exit the room easily.

3.6 Operation without flue connection

  • Air is filtered through the carbon filter and recirculated in the room. Carbon filter is used when it is impossible to use a flue in the house.
  • In flueless use, remove the flaps inside the flue adapter.
  • Remove the oil filter. To install the carbon filter, fit the filter to the tabs by centring it on the plastic piece on both sides of the fan body. Tighten it by turning right or left.
  • Replace aluminium oil filter.

Cleaning and maintenance

The device should be cleaned and maintained regularly. Failure to keep the device clean will adversely affect the service life of the device. For cleaning and maintenance, follow the instructions stated in the manual.
Before cleaning and maintenance, unplug the product or turn off the switch.
Non-compliance with the provisions associated with the cleaning of the device and replacement of the filters may result in a risk of fire. Therefore, it is recommended to follow the guidelines stated here. The manufacturer is not responsible for the engine damages or fires originating from the improper use.
Clean using only a cloth dampened with a neutral liquid detergent. Do not use abrasive products or alcohol.
4.1 Cleaning of the grease filter
The grease filter must be cleaned once a month using non aggressive detergents, either by hand or in the dishwasher, which must be set to a low temperature and a short cycle. When washed in a dishwasher, the grease filter may discolor slightly, but this does not affect its filtering capacity. You may wash your grease filters in the dishwasher.
CAUTION: In case of normal use, clean your filter once in a month.
4.2 NON-washable activated charcoal filter
The saturation of the charcoal filter occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter.
Assembly
Hook the charcoal filter at the back on the metal tongue of the hood first, then on the front with the two knobs.
Disassembly
Remove the charcoal filter by turning the knobs fixing it to the hood by 90°.beko HCF61620X Cooker Hood - charcoal filter CAUTION

  • Carbon filter shall never be was- hed.
  • Replace carbon filters once every 3 months.
  • You can obtain the carbon filter from the authorized services.

Setting up the device

WARNING: Before starting the ins- tallation, read the safety information on User Manual.
WARNING: Failure to install with screws and stabilizers in accordance with these instructions may result in electric shock.
Please refer to page 148 for the installation guide.
For the installation of the hood, please contact the nearest Authorized Service.
It is the customer’s responsibility to prepare the location and electrical installation of the hood.
5.1 Position of the appliancebeko HCF61620X Cooker Hood -
appliance

  • Distance between the cooker and the cooker hood must be considered prior to assembly. This distance should be 65 cm.
  • Distance must be measured from the surface of grate for gas cookers, From surface of glass for electric cookers.

5.2 Installation accessoriesbeko HCF61620X Cooker Hood - Installation
accessories

  1. Installation template
  2. Chimney clamp
  3. Chimney connection plate
  4. Ø5×45 screw
  5. Ø8×40 dowel
  6. M5x16 screw
  7. Ø2,9×6,5 screw
  8. Ø3,9×9 screw
  9. Washer
  10. Power supply cord

5.3 Storage

  • If you do not intend to use the appliance for a long time, please store it carefully.
  • Please make sure that the appliance is unplugged, cooled down and totally dry.
  • Store the appliance in a cool and dry place.
  • Keep the appliance out of the reach of children

5.4 Handling and transportation

  • During handling and transportation, carry the appliance in its original packaging. The packa- ging of the appliance protects it against physical damages.
  • Do not place heavy loads on the appliance or the packaging. The appliance may be damaged.
  • Dropping the appliance will render it nonoperational or cause permanent damage.

Troubleshooting

Troubleshooting Reason Help
The product does not work. Check your fuse. Your fuse might be closed, make

it work.
The product does not work.| Check the electrical connection.| The mains voltage should be between 220- 240 V.
The product does not work.| Check the electrical connection.| Check if the other products in your kitchen are working or not.
The lighting lamp does not work.| Check the electrical connection.| The mains voltage should be between 220- 240 V.
The lighting lamp does not work.| Check the lamp switch.| The lamp switch should be in the “on” position.
The lighting lamp does not work.| Check the lamps.| The lamps of the product should not be faulty.
The air intake of the pro- duct is poor.| Check the aluminum filter.| The aluminum filter should be cleaned at least once a month under normal conditions.
The air intake of the pro- duct is poor.| Check the air vent flue.| The air vent flue should be in the “on” po- sition.
The air intake of the pro- duct is poor.| Check the carbon filter.| For products with carbon filters, the filter sho- uld normally be changed every 3 months.
beko HCF61620X Cooker Hood - fig| beko HCF61620X
Cooker Hood - fig 1
---|---
beko HCF61620X Cooker Hood - fig 2| beko
HCF61620X Cooker Hood - fig 3
beko HCF61620X Cooker Hood - fig 4| beko
HCF61620X Cooker Hood - fig 5
beko HCF61620X Cooker Hood - fig 6| beko
HCF61620X Cooker Hood - fig 7

Arçelik A.Ş.
Karaağaç Caddesi No: 2-6, 34445,
Sütlüce, İstanbul, Türkiye
www.beko.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals