DSC HS2128 Series Power Neo Security Alarm Control Panel Instruction Manual

To download the full installation and user manuals and register your product, please visit: or scan the QR code to the right.

www.DSC.com/m/29009047
PowerSeries Neo V1 .1 Alarm Control Installation Guide

Quick Setup

Plan| Plan the installation including all alarm detection devices, zone expanders, keypads and other required modules.
---|---
Mount| Decide on a location for the alarm panel and secure it to the wall using suitable mounting hardware.
Wire| Complete all wiring including modules, zones, bells/sirens, telephone line connections and ground  connections. Record module serial numbers on page 19.
Power| Connect the battery and power up the system. The battery must be connected.
Enroll First Keypad| Hardwired: Wire the keypad to the Corbus, power up the alarm panel then press any button on the  keypad. Wireless:
Wire the HSM2Host to the Corbus, then power up the alarm panel and a wireless keypad. Press any  button on the keypad to enroll it. The HSM2Host is then enrolled on the alarm panel.
Alternately, enroll an RF keypad.
Enroll modukes| [][8][Installer Code][902] subsection [000]. Press[] to begin auto-enrollment. Module slots are  automatically assigned. Use scroll keys to view slots. Change slot by typing a 2-digit number.
Enroll wireless device| [][8][Installer Code][804] subsection [000]. Note: An HSM2HOST or RF keypad must be enrolled first.
Program| Basic programming: [][8][installer code] [001]/[002]> Zone Type/Zone Attribute [005]>[001]  Partition 1 Timers: – Entry
Delay 1-Entry Delay 2-Exit Delay [301]>[001] Phone #1 [310]>[000] System Account Code
Test| Test the panel completely to ensure that all features and functions operate as programmed. -[901] Walk Test –[904] [000] Wireless Placement Test

Compatible Devices

Throughout this document, x in the model number represents the operating frequency of the device as follows: 9 (912-919 MHz), 8 (868MHz), 4 ( 433MHz).
Note: Only models operating in the band 912-919 MHz are UL/ULC listed where indicated. Only UL approved devices are to be used with UL/ULC listed systems.

Table 1-1 Compatible Devices
Modules

Wireless keypads:| HS2LCDWFUL
HS2LCD WFPxUL| HS2LCDWFPVRUL
---|---|---
Hardwired keypads with 2-way wireless integration module:| HS2LCDREUL
HS2LCDRFPRU| HS2ICNRExUL
HS2ICNRFPRU
Hardwired keypads:| HS2LCDU
HS2LCDPUL
HS2ICNUL| HS2ICNPU
HS2LEDL
Touchscreen Keypad| HS2TCHP|
2-way wireless integration module:| HSM2HOST\xUL|
8-zone expander:| HSM2108UL|
8-output expander:| HSM2208UL|
Power supply:| HSM2300UL|
4 high current output expander:| HSM2204UL|
Alternate communicator:| 3G2080UL
3G2080RUL
TL280
TL28ORUL| TL2803GU
TL2803GR
PCL-422UL

Note: For ULC-s559 Listed applications the HS2TCHP touch screen keypad is for supplementary use only.

Hardwired Devices

FSA-410\R1UL
FSA-410xSUL| FSA-410xRUL
FSA-410xRTUL
FSA-410xRSUL
y= A, B, or C| FSA-410xSTUL| FSA-410xRSTUL
A: ULC listed models
B: UL listed models
C: European and Australian models| FSA-410xLSTU!| FSA-410xLRSTU
CO detectors:| CO-12/241
12-24SIRUL
FW-CO12UL| FW-CO1224U
CO1224UL

Wire less Devices

PGx929UL
Wireless PG panic key| PGx938UL
Wireless PG 2-button key| PGx949UL
Wireless PG sirens:| PGx901 UL
PG8x91 1UL
Wireless PG repeater:| PGx920UL
Wireless PG door/window contacts:| PG975UL
Wire less PG door/window contact w/ AUX| PG»x945UL

Central Station Receivers
SO-System I, II, III, IV, 5
Enclosures
PC5003C, PC4050CR (ULC Fire Monitoring), PC4050CAR (UL Commercial Burg), CMC-I(UL Commercial Burg), PC405 l C. Other enclosures are available to suit a variety of system configurations.

WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.

Safety Instructions for Service Personnel

Warning: When using equipment connected to the telephone network, always follow the basic safety instructions provided with this product. Save these instructions for future reference. Inform the end-user of the safety precautions that must be observed when operating this equipment.

Before Installing The Equipment
Ensure your package includes the following items:

• Installation and User manuals, including the SAFETY INSTRUCTIONS.
  READ and SAVE these instructions!
  Follow all WARNINGS AND INSTRUCTIONS specified within this document and/or on the equipment.

• HS201 6/HS20 l 6/2032/2064/2128 alarm controller

• Power Supply, direct plug-in

• Mounting hardware

Selecting A Suitable Location For The Alarm Controller
Use the following list as a guide to find a suitable location to install this equipment:

• Locate near a telephone socket and power outlet.
• Select a location free from vibration and shock.
• Place alarm controller on a flat, stable surface and follow the installation instructions.
  Do NOT locate this product where people may walk on the secondary circuit cable(s).
  Do NOT connect alarm controller to electrical the same circuit as large appliances.
  Do NOT select a location that exposes your alarm controller to direct sunlight, excessive heat, moisture, vapors, chemicals or dust.
  Do NOT install this equipment near water. (e.g., bath tub, kitchen/laundry sink, wet basement, near a swimming pool).
  Do NOT install this equipment and accessories in areas where risk of explosion exists.
  Do NOT connect this equipment to electrical outlets controlled by wall switches or automatic timers.
  A VOID interference sources.
  A VOID installing equipment near heaters, air conditioners, ventilators, and refrigerators.
  A VOID locating equipment close to or on top of large metal objects (e.g., wall studs).
  See “Locating Detectors and Escape Plan” on page 20 for information on locating smoke and CO detectors.

SAFETY Precautions Required During Installation

• NEVER install this equipment and/or telephone wiring during a lightning storm.
• NEVER touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Position cables so that accidents can not occur. Connected cables must NOT be subject to excessive mechanical strain.
• Use only the power supply provided with this equipment. Use of unau­ thorized power supplies may cause damage.
• For direct plug-in versions, use the transformer supplied with the device.

WARNING: THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST BE QUICKLY DISCONNECTED. IT  IS IMPERATIVE THAT ACCESS TO THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET IS NEVER OBSTRUCTED.

IMPORTANT NOTE FOR NORTH AMERICA!
This alarm system must be installed and used within an environment that provides the pollution degree max 2 and over-voltages category II NON- HAZARDOUS LOCATIONS, indoor only. The equipment is DIRECT PLUG-IN (external transformer) and is  designed to be installed, serviced and/or repaired by service persons only; [service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task  and of measures to minimize the risks to that person or other persons].
This equipment has no mains on/off switch; if the equipment must be quickly disconnected, the plug of the direct plug-in power supply is intended to serve as the disconnecting device; it is imperative that access to the mains plug and associated mains socket/outlet, is never obstructed. There are no parts replaceable by the end-user within this equipment. The wiring (cables) used for installation of the alarm system and accessories, shall be insulated with PVC, TFE, PTFE, FEP, Neoprene or Polyamide.
(a) The equipment enclosure must be secured to the building structure before operation.
(b) Internal wiring must be routed in a manner that prevents:

• Excessive strain or loosening of wire on terminal connections;
• Damage of conductor insulation

(c) Disposal of used batteries must be made in accordance with local waste recovery and recycling regulations.
(d) Before servicing, DISCONNECT the power and telephone connection.
(e) DO NOT route any wiring over circuit boards.
(f) The installer is responsible to ensure that a readily accessible disconnect device is incorporated in the building for permanently connected installations.
The power supply must be Class II, FAIL SAFE with double or reinforced insulation between the PRIMARY and SECONDARY CIRCUIT/ENCLOSURE and be an approved type acceptable to the local authorities. All national wiring rules must be observed.

Installation

Mounting the Enclosure
Locate the panel in a dry area, preferably near an unswitched AC power source and the incoming telephone line. Complete all wiring before applying AC or connecting the battery.

Terminal Descriptions
The following terminals are available on the PowerSeries Neo alarm controller.

current when system demands exceed the power output of the transformer, such as when the system is in alarm.
Do not connect the battery until all other wiring is complete.
AC| Power terminals.
Connect the battery before connecting the AC. Do not connect the battery or transformer until all other wiring is complete.
AUX+, AUX-| Auxiliary terminals. Use to power modules, detectors, relays, LEDs, etc. (700mA MAX). Connect the positive side of device to AUX+, the negative side to AUX-.
BELL+, BELL-| Bell/Siren power (700mA MAX). Connect the positive side of any alarm warning device to BELL+, the negative side to BELL-.
RED, BLK, YEL, GRN| Coitus terminals. Use to provide communication between the alarm controller and connected modules. Each module has four Corbus terminals that must be connected to the Coitus.
PGM1 to PGM4| Programmable output terminals. Use to activate devices such as LEDs.
(PGM1, PGM3, and PGM4: 50mA PGM2: 300mA or can be configured as an input)
Z1 to Z8 COM| Zone input terminals. Ideally, each zone should have one detection device; however, multiple detection devices can be wired to the same zone.
EGND| Earth ground connection.
TIP, RING, T-1, R-1| Telephone line terminals.
PCLINK_1| DLS/SA
PCLINK_2| DLS/SA, Alternate Communicator

Corbus Wiring
The RED and BLK Corbus terminals are used to provide power while YEL and GRN are used for data communications. The 4 Corbus terminals of the alarm controller must be connected to the 4 Corbus terminals or wires of each module.
The following conditions apply:

• Corbus should be run with minimum 22 gauge quad, two pair twisted preferred.
• The modules can be home run to the panel, connected in series or can be T-tapped.
• Do not use shielded wire for Corbus wiring.

Note: Any module can be connected anywhere along the Corbus. Separate wire runs for keypads, zone expanders etc. are not necessary.
Note: No module can be more than 1,000’/305m (in wire length) from the panel. Do not use shielded wire for Corbus wiring.

Module (A) is wired correctly as it is within 1,000’/305m of the panel, in wire distance. Module (B) is wired correctly as it is within 1,000’/305m of the panel, in wire distance. Module (C) is NOT wired correctly as it is farther than 1,000’/305m from the panel.

Current Ratings
In order for the system to operate properly, the power output of the alarm controller and power supply modules cannot be exceeded. Use the following data to ensure that the available current is not exceeded.

Table 1-1 System Output Ratings

keypad, expansion module and accessory connected to AUX or Corbus. At least 100mA must be reserved for the Corbus.
BELL:| 700mA. Continuous rating.
2.0A. short term. Available only with standby battery connected. Not for UL/ULC or EN certified applications.
HSM2208| AUX:| 250mA. Continuous rating. Subtract for each device connected. Subtract the total load on this terminal from the alarm panel AUX/Corbus output.
HSM2108| AUX:| 100mA. Subtract for each device connected. Subtract the total load on this terminal from the panel AUX/Corbus output.

Alarm Control Panel
AUX – 700mA available for devices connected to the AUX and PGM terminals, and modules connected to Corbus terminals. At least l00mA must be reserved for the Corbus.

Alarm Controller Current Calculation
Panel Calculation
Maximum (Standby or Alarm)

AUX (700mA max. including PGMs 1-4)|
---|---
Corbus (700mA max.)|
PCLink+ (Alt. Com.: 125mA)|
Total (must not exceed 700mA)|

* See “Corbus Current Calculation Chart” on page 3.
For UL, ULC and Commercial Listed applications, the total standby and alarm current cannot exceed 700mA.
Table 1-2 Corbus Current Calculation Chart**

*These units draw current from the Corbus to power devices external to the module. This current must be added to the total Corbus current. See manufacturer’s specifications for the current draw of each device.
** For HSM2955 current draw refer to HSM2955 installation manual.

Capacitance Limits
An increase in capacitance on the Corbus affects data transmission and causes the system to slow down. Capacitance increases for every foot of wire added to the Corbus. The capacitance rating of the wire used will determine the maximum length of the Corbus.

Table 1-3 Wire Capacitance

AC (UL Listed Installations)
Primary: 120VAC/60Hz./0.JJA
Secondary: 16.5VAC/40VA DSC PTDl640U, DSC PTCl640U Class 2 transformer.
Note: Use DSC PTO 1640 for Canadian installations.
Warning: Do not connect the battery or transformer until all other wiring is complete.
For ULC S559 applications, Standex transformer (Model FTC3716) shall be employed for direct-wiring.
Note: For UL/ULC installations use only 60Hz.
Batteries
Do not connect the battery until all other wiring is complete.
Note: A sealed, rechargeable, lead acid battery or gel type battery is required to meet UL requirements for power standby times.
Connect the RED battery lead to the positive battery terminal and the BLACK battery lead to the negative battery terminal.
Note: Refer to “Aux Loading and Battery Selection” on page 23.

Additional Wiring
Zone Wiring
Power down the alarm controller and complete all zone wiring.
Zones can be wired to supervise normally open devices (e.g., smoke detectors) or normally closed devices (e.g., door contacts). The alarm panel can also be programmed for single end-of-line or double end-of-line resistors.
Zone programming is done using the following programming sections:

• [00 I] selects zone definition

• [0 I 3] Opt [I] for normally closed or EOL; Opt [2] for SEO L or DEOL

• [201-208] partition assignment.
  Observe the following guidelines when wiring zones:

• For UL listed installations use SEOL or DEOL only

• Minimum 22AWG wire, maximum 18 AWG

• Do not use shielded wire

• Do not exceed 100 wire resistance. Refer to the following table:

Table 1-4 Burglary Zone Wiring Chart

Aux Power Wiring
These terminals provide 11.3-12.5VDC/700mA of current (shared with PGM outputs). Connect the positive side of any device to the AUX+ terminal, the negative side to GND. The AUX output is protected; if too much current is drawn from these tenninals  (wiring short) the output is temporarily shut off until the problem is corrected.
Note: If using a 12V, 14Ah battery, maximum AUX capacity for 24-hour standby is 470mA.

PGM Wiring
Min/max operating voltages for devices, sensors and modules is 9.5VDC – 14VDC.
PGMs switch to ground when activated from the alarm controller. Connect the positive side of the device to the AUX+ terminal and the negative side to a PGM terminal.
PGM 1, 3, 4 supply up to 50mA; PGM 2 supplies up to 300mA.
A relay is required for current levels greater than 50mA or 300mA. PGM2 can also be used for 2-wire smoke detectors, 24-hr burglary input alann.
Note: Use SEOL resistors on Fire zones only.

Figure 1-2 LED Output with Current Limiting Resistor and Optional Relay Driver Output.
UL Compatibility ID For FSA-21 OB Series is: FS200
Note: For ULC listed installations, use FSA-210A and FSA-41 0A series.

Single End-of-Line (SEOL) Resistor
When SEOL resistors are installed at the end of a zone loop, the alarm panel detects if the circuit is secure, open, or shorted. The SEOL resistor must be installed at the end of the loop for proper supervision.
To enable SEOL supervision, program section [013], options [l] and [2] to OFF.
Note: This option should be selected if either normalJy closed or normally open detection devices or contacts are used.

Double End of Line (DEOL) Resistors
When double end-of-line (DEOL) resistors are installed at the end of a zone loop, the second resistor enables the panel to determine if the zone is in open, closed, tampered or faulted.
Note: Any zone programmed for Fire or 24-hr Supervisory must be wired with a SEOL resistor regardless of the type of zone wiring supervision selected for the panel. If you change the zone supervision options from
DEOL to SEOL or from NC to DEOL, power the system down completely, then power it back up for correct operation.
To enable DEOL supervision, program section [013], option [1] to OFF and option [2] to ON.

Bell Wiring
These terminals supply 700mA of current at 10.4-12.5VDC for commercial/ residential installations. To comply with NFPA 72 Temporal
Three Pattern requirements, section [013] Opt [8] must be ON. Note that steady, pulsed alarms are also supported.

Figure 1-5 Bell Wiring
The Bell output is supervised and power limited by 2A thermistor. If unused, connect a 1000Q resistor across Bell+ and Bell- to prevent the panel from displaying a trouble.
Telephone Line Wiring
Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ- 31x connector as indicated in the following diagram. For connection of multiple devices to the telephone line, wire in the sequence indicated. Use 26 A WG wire minimum for wiring. 

Telephone format is programmed in option [350]. Telephone call directions are programmed in options [311]- [318].
Ground Wiring

Note: Using an insulated green wire (minimum 22A WG), connect the EGND terminal on the Corbus and the grounding wire from the building electrical installation to any of the available holes on the back or side of the metal cabinet. See the diagram attached to the cabinet for suggested GND point location and hardware recommendations.
Note: Wire and installation hardware not included.

Enrollment
All optional modules and devices must be enrolled on the system. During enrollment, the electronic serial number (ESN) of each device is identified to the control panel and zones are assigned. A wireless transceiver HSM2HOST or an RF keypad must be  enrolled first before wireless devices can be enrolled.

Enrolling Modules
During automatic and manual enrollment, if an attempt is made to enroll more than the maximum number of modules, an error tone sounds and a message is displayed on LCD keypads.
Table 1-5 Module Capacity

Module
HSM2108 8 Zone expander| HS2016
I| HS2032
3| HS2064
7| HS2128
15
---|---|---|---|---
HSM2208 8 Output expander| 2| 4| 8| 16
Wireless Keypad: HS2LCDRF(P)4
HS2ICNRF(P)4
HS2LCDWF(P)(V)4| 8| 8| 8| 16
HS2TCHP Touchscreen Keypad| 8| 8| 8| 16
HSM2300 Power Supply lA| 3| 3| 3| 4
HSM2204 4 High-current Output| I| 1| 3| 4
HSM2HOSTx Transceiver| 1| 1| 1| 1
HSM2955 (not UL evaluated)| 1| 1| 1| 1

Modules can be enrolled automatically or manually using section [902] of Installer programming.
To confirm that a module has been successfully enrolled, use Installer Programming section [903].
Enroll Wireless Devices
Wireless devices are enrolled via the wireless transceiver module and Installer Programming section [804][000].
Auto Enrollment
To enroll a wireless device using this method, press and hold the Enroll button on the device for 2-5 seconds until the LED lights then release the button. The alarm panel automatically recognizes the device and the keypad displays a confirmation message. The  device ID and next available zone number are displayed. Press [*] to accept or scroll to another available zone number. Batteries must be installed in the wireless device in order to enroll.

Pre-Enrollment
Pre-enrollment is a two step process. The first step requires entering each device ID ([804][001]-[716]). Every wireless device has an ID printed on the sticker attached to the device. The format is XXX-YYYY where:

• XXX identifies the type or model of the device
• YYYY is a short encrypted ID used by the system to identify the specific device

Pre-enrollment can be done at a remote location and using DLS/SA. The second step is to press the enrollment button on the device, usually done on location. Installer Programming does not have to be entered at this step.
Both steps must be performed in order to complete the enrollment.

Programming Methods

The alarm system can be programmed using the following methods:
Table 1-6 Programming Methods

Template
programming| Use pre-defined templates to
quickly apply basic programming
and to set up DLS downloading.| Press [899] at the
“Enter Section”
screen.
See Template
Programming below
for details.
DLS
programming| Download and apply programming
using DLS 5 v1.3 for Neo v1.0
panels and DLS 5 v1.4+ for Neo
v1.0 and v1.1 products.| For local DLS, use a
PC-Link cable and
laptop with DLS-5
software installed.
For remote DLS, use
a telephone line,
cellular network or
the Internet.
Installer
programming| Manually program all alarm system
and device options.| Press [*][8][installer code] while the
system is disarmed.

Viewing Programming
Programming sections can be viewed from any system keypad. The method for viewing and selecting programming options using LCD, LED and ICON keypads depends on the keypad type used. See below for specific instructions on programming with each  keypad type.
Generally, programming options are accessed in the following way:

1. Enter Installer Programming mode ([*][8]).
2. Navigate to a specific programming section.
3. Select an option to view or change its programming.

All programming options are numbered and can be accessed by navigating through the menu (LCD) or by keying in the program section number. For toggle options, the name of the option is displayed (LCD) or LEDs 1-8 are illuminated (LED and ICON).
Use the keypad numbers to toggle options on or off. Sections requiring data input, such as phone numbers, display the full data in fields up to 32 characters long (LCD). To input data, use the scroll keys to select a character then press the keypad button  corresponding to the number/letter required. Scroll to the next character and repeat the procedure as needed.
Press the [ #] key to save changes and exit the program section.

Minimum Required Programming

Once basic installation of the alarm panel is complete, the following general configuration options can be set.
[000] Language Selection
(LCD keypads only)
Use this section to set the language displayed by LCD keypads. To select a language:

1. Enter Installer Programming: [*][8][Installer Code].
2. Enter programming section [000]>[000].
3. Key in the 2-digit number corresponding to the language required. See below:

Time and Date
Use this section to program the alarm system clock.
Menu: [][6][Master Code]> Time and Date
Keypad: [][6][Master Code]+ 01
Enter time and date using the following format: (HH:MM); (MM-DD­ YY). Valid time entries are 00-23 hours, 00-59 minutes. Valid date entries are 01-12 months, 01-31 days.

Setting Up a Partition
Partitions are added or removed from the system by applying or removing a partition mask via Installer Programming section [200]. The number of available partitions depends on the alarm panel model.

Bell/Siren Operation
Each partition must have a siren. The system siren connected to the bell output of the alarm controller can be mounted in a central location within hearing range of all partitions. Each partition can also have wireless sirens activated only on the assigned partition.

Keypad Partition Setup
Keypads can be configured to control an individual partition or all partitions. In general, a partition keypad controls the partition it is assigned to. A Global keypad controls all partitions. Global keypads should be placed in common areas of the premises, such as  points of entry or reception areas, where the ability to arm and disarm more than one partition at a time is required.
Partition keypads can also be temporarily loaned to other partitions.

To select a keypad operating mode:

1. Enter Installer Programming: [*] [8] [installer code].

2. Select [861]-[876] to program keypads 1-16.
   • Press [000] for partition assignment.
   • For Global operation, key in 00.
   • To assign a keypad to a partition, key in O 1-08 for partition 1-8.

3. Press the [ #] and reapeat step 2 for next keypad. When finished programming all keypads, press the[#] key twice to exit programming.

Users are assigned partition access rights via the [*][5] menu.
Assign sirens to partitions:
[804 ]>[000]>[551 ]-[ 556]>[000] Set up partition account codes:
[310]>[001 ]-[008]

Set up partition timers:

• Entry/exit delay, settle delay – [005]>[001]-[008]
• Automatic arming/disarming schedule – [151]-[158]>[001]/[002]
• Auto disarming holiday schedule [151]-[158]>[003]
• No activity arming- [151]-[158]>[006]
• Automatic clock adjust [005]>[000], option 6
• Delay between dialing attempts -[377]>[012]

Assign Zone Types
A zone type defines how a zone operates within the system and how it responds when triggered.

Keyswitch Disarm
027 – Fire Supervisory| 071 – Door Bell

• Not UL evaluated| 072-Push to Set

Assign zone attributes:
[002]>[001]-[128]>Select one of the following zone attributes:

1. Bell Audible
2. Bell Steady
3. Chime Function
4. Bypass Enabled
5. ForceArm
6. Swinger Shutdown
7. Transmission Delay
8. Burglary Verification
9. Normally Closed EOL
10. Single EOL
11. Double EOL
12. Fast/Normal Loop Response
13. Zone 2-way Audio Activation
14. Hold Up Verification

Create labels:
[000]>[001]-[821] 2 x 14 ASCII characters.
Add access codes:
To program an access code: [006] then one of the following:
[001] Installer code
[002] Master code
[003] –Maintenance code
Access codes are either 4 or 6 digits in length, depending on the setting of programming section [041]. Duplicate codes are not valid.

Alternate Communicator Setup
The alternate communicator is an optional wireless or ethernet communications device that can be used as a backup to the PSTN connection or as a primary means of communication between the alarm panel and the central monitoring station. The alternate  communicator communicates via 3G (HSP A) or Ethernet.
The following configuration steps are required to set up the alternate communicator:

• Install the alternate communicator and wire it to the alarm panel (use PCLINK_2 header)
• Enroll the alternate cellular communicator with Connect 24
• Set the communication path: [300]
• Enable the alternate communicator: [382] option 5
• Enable event reporting: [307]/[308]
• Program communication delay timer: [3 77]
• Program D LS access: [ 401] option 07
  Refer to the 3G2080(R)/ TL2803G(R)/ TL280(R) installation manual for details.

[300] Panel/Receiver Communication Paths
This section is used to select the path of communications between the alarm system and the central station.
To use PSTN as the communications path, program section [300] options 001 through 004 as [01] PSTN 1.
To use the alternate communicator to establish a communications path, program two of the receivers (section [300] options 001, 002, 003 or 004) as [03] and [04] for Ethernet, and two of the receivers as [05] and [06] for cellular.

Testing the System

Installer Walk Test
Walk test enables the installer to test the operation of each detector by tripping zones, causing an actual alarm. Enter section [901] to initiate a walk test. When a zone is tripped, all system sirens emit a tone to indicate that the zone is working correctly.
After 15 minutes without zone activity, the walk test terminates automatically. To manually exit walk test mode, enter [901] again.
Viewing the Event Buffer
The event buffer contains logs of events that have occurred on the alarm system beginning with the most recent. The capacity of the event buffer is scalable and can hold 500/1000 events (depending on panel model) before rolling over. The buffer displays events according to their time stamp, beginning with the most recent. The event buffer can be uploaded using DLS.
Each event displays the time and date, a description of the event, the zone label, access code number or any other pertinent information. To view the event buffer, press [][6][Master Code][].

Troubleshooting

LCD programmable-message keypad:

• Press [*] [2] followed by access code if required to view a trouble condition
• The trouble light flashes and the LCD displays the first trouble condition
• Use the arrow keys to scroll through all trouble conditions present on the system
  Note: When additional information is available for a specific trouble condition, a [] is displayed. Press the [] key to view the additional information.

LED and ICON keypads:

• Press [*] [2] to view a trouble condition
• The trouble light flashes
• Refer to the trouble summary list below to determine the trouble condition(s) present on the system

[][2] Trouble Display
This feature is used to view system troubles. If a trouble is present, the keypad Trouble indicator illuminates and an audible indication is emitted (two short beeps every 10 seconds, except while in AC failure). Silence the audible indicator by pressing[#].
Troubles may be viewed while the system is armed or disarmed. The system may be programmed to show all troubles while armed or only fire troubles.
The system can be configured to require a user code to view [*][2] system troubles. See section [023] option 5.
To view trouble conditions:

• Press [*][2] to enter the Trouble menu.
• On an LCD keypad, scroll to a trouble type then press [*] to view the specific trouble. The zone name and trouble condition for each trouble are displayed on the screen.
• On LED/ICON keypads, zone indicator lights illuminate to identify existing trouble types ( e.g., Zone light 1 represents Ser­ vice Required trouble type). Press the number key corresponding to a zone light to view the specific trouble. Lights 1-12 illuminate to  indicate the trouble as follows:

Table 1-7 : Trouble Indications
Trouble 01 Service Required:
[01] Bell Circuit Trouble: The bell circuit is open.
[02] RF Jam: The HSM2HOSTx has detected an RF Jam condition.
[03] Aux Supply Trouble: The alarm controller, HSM2204 or HSM2300 has an overcurrent condition on Aux.
[04] Loss of Clock: System time and date require programming.
[05] Output 1 Fault: An HSM2204 module has detected an open condition on output #1.
Trouble 02 — Battery Trouble:
[01] Panel Low Battery Trouble: The battery voltage (under load) is below 11.5V. Restores at 12.5V.
[02] Panel No Battery: No battery connected to alarm controller.
[04] HSM2204 01 – 04 Low Battery: An HSM2204 has a battery voltage less than 11.5V.
[05] HSM2204 01 – 04 No Battery: No battery connected to HSM2204.
[07] HSM2300 01 – 04 Low Battery: An HSM2300 has a battery voltage less than 11.5V
[08] HSM2300 01 – 04 No Battery: No battery connected to HSM2300.
Trouble 03-Bus Voltage:
[01] HSM2HOSTx Bus Low Voltage: The HSM2HOSTx module has measured less than 6.3V on its Aux input.
[02] Keypad 01- 16 Bus Low Voltage: A hardwired keypad has a bus voltage of less than 6.9V for ICON/LCD (RF version) and 7.7V for non-RF models.
[04] HSM2 l 08 01 – 15 Bus Low Voltage: A zone expander has a bus voltage of less than 5.9V.
[05] HSM2300 01 – 04 Bus Low Voltage: A power supply has a bus voltage of less than 6.9V.
[06] HSM2204 01 – 04 Bus Low Voltage: A high current output module has a bus voltage of less than 6.9V.
[08] HSM2208 01- 16 Bus Low Voltage: The low current output module has detected a voltage less than 5.9V on its aux input.
[09] HSM2955 Bus Low Voltage: The audio module has detected a voltage less than 9.65V on its aux input.

Trouble 04– AC Troubles:
[01] Zone 001 – 128 AC Trouble: An AC trouble has been detected on a PGX934 PIR + Camera.
[03) Siren 01- 16 AC: A siren has an AC trouble.
[04] Repeater 01 – 08 AC: A wireless repeater has an AC trouble.
[05] HSM2300 01 -04 AC: An HSM2300 has an AC trouble.
[06] HSM2204 01 -04 AC: An HSM2204 has an AC trouble.
[07) Panel AC: The alarm controller has an AC failure condition.

Trouble 05 – Device Faults:
[01) Zone 001 – 128: A zone is in fault. Additional information displayed on LCD keypads for the following troubles: Fire Trouble (2-W Smoke, PGX916, PGX926), Freeze (PGX905), Self Test (PGX984), CO (PGX913), and Probe Disconnected (PGX905). Also  generated by a short on hardwired zones when DEOL is used or by a wireless supervisory fault.
[02) Keypad 01- 16: A wireless or hardwired keypad is in fault.
[03] Siren O 1- 16: A siren is in fault.
[04] Repeater 01 – 08: A wireless repeater is in fault (supervisory or loss of AC/DC).

Trouble 06 — Device Low Battery:
[01] Zone 001- 128: Wireless zone has a low battery.
[02] Keypad 01-16: Keypad has a low battery.
[03] Siren 01- 16: Siren has a low battery.
[04) Repeater 01 – 08: Repeater has a low battery.
[05] User 01- 95: Wireless Key has a low battery.

Trouble 07 -Device Tampers:
[01] Zone 001- 128 Tamper: A wireless or hardwired zone configured for DEOL operation is in tamper.
[02) Keypad 01- 16 Tamper: A hardwired or wireless keypad is in tamper.
[03) Siren 01- 16 Tamper: A wireless siren is in tamper.
[04] Repeater 01- 08 Tamper: A wireless repeater is in tamper.
[05] Audio Station 01- 04 Tamper: An audio station connected to an HSM2955 is in tamper.

Trouble 08 –RF Delinquency Trouble:
[01] Zone 001- 128 RF Delinquency: No response from a wireless zone for 13 minutes. This trouble prevents arming until acknowledged or cleared using [*][2].
[02] Keypad 01 – 16 RF Delinquency: No response from a wireless keypad for 13 minutes.
[03] Siren 01- 16 RF Delinquency: No response from a wireless siren for 13 minutes.
[04] Repeater 01- 16 RF Delinquency: No response from a wireless repeater for 13 minutes.

Trouble 09 — Module Supervisory Trouble:
[01) HSM2HOSTx not responding.
[02] Keypad O I – 16 not responding.
[04] HSM2 l 08 01- 15 not responding.
[05] HSM2300 01 – 04 not responding.
[06) HSM2204 01- 04 not responding.
[08] HSM2208 01 – 16 not responding.
[09] HSM2955 is not responding.
Trouble 10 — Module Tamper:
[01] HSM2HOSTx Tamper.
[02] Keypad O 1 – 16 Tamper.
[04] HSM2108 01- 15 Tamper.
[05) HSM2300 01 – 04 Tamper.
[06] HSM2204 01 – 04 Tamper.
[08] HSM2208 01- 16 Tamper.
[09] HSM2955 Tamper

Trouble 11-Communications:
[01] TLM: Telephone line disconnected from control panel.
[02] Receiver 01-04 FTC Trouble: Failure to communicate using programmed receiver paths.
[03] Alt. Comm SIM Lock: SIM card has incorrect or unrecognized PIN.
[04] Alt. Comm Cellular: Radio or SIM card failure, low signal strength detected, or cellular network fault.
[05] Alt. Comm Ethernet: Ethernet connection unavailable. A valid IP address is either not programmed or the module was unable to get an IP with DHCP.
[06] Receiver 01-04 Absent: Alternate communicator unable to initialize a receiver.
[07] Receiver 01-04 Supervision: Alternate communicator unable to communicate with a receiver.
[09] Alt. Comm Fault: The alternate communicator has stopped responding.
[10] Alt Comm FTC Trouble: The alternate communicator has failed to communicate an internal event not generated by the panel.

Trouble 12-Not Networked Troubles:
[01] Zone 001-128 Not Networked Trouble: Generated when a zone becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.
[02] Keypad 01-16 Not Networked Trouble: Generated when a keypad becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.
[03] Siren 0 1-16 Not Networked Trouble: Generated when a siren becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.
[04] Repeater 01-08 Not Networked Trouble: Generated when a repeater becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.
[05] User 01-95 Not Networked Trouble: Generated when a wireless key becomes out of sync with the wireless network or has not been synchronized with the network after enrollment.

IMPORTANT!
Ensure you have the following information available before contacting Customer Support:

• Alarm controller type and version, (e.g., HSM2064 1.0):
  Note: Version number can be accessed by entering [*] [Installer Code] [900] on any LCD keypad. This information is also located on a sticker on the printed circuit board.

• List of modules connected to control panel, (e.g., HSM2108, HSM2HOSTx etc.) .

Specifications

Zone Configuration

• 16, 32, 64, or 128 wireless zones supported and up to 8 hard­ wired zones available on the controller
• 40 zone types and 14 programmable zone attributes
• Zone configurations available: normally closed, single EOL and DEOL supervised
• Hardwired zone expansion (fully supervised) available using the model HSM2108 ( eight zone expander module)
• Wireless zone expansion (fully supervised) available using the HSM2Host 2-way wireless integration module ( operating at 915MHz (North America), 433MHz (Europe) and 868MHz (inter­ national)

Access Codes

• Up to 97 access codes: 94 (level 2-EN), one system master code (level 3-EN), one installer code (level 3-EN), and one maintenance code
• Programmable attributes for each user code (see “Access Code Attributes” on page 1)
• When using 6-digit access codes, the minimum number of vari­ ations of access codes are 10526 for HS2128/HS2064,13888 for HS2032 and 20833 for HS2016

Warning Device Output

• Integral sounder capable of 85 dB @ 3m, self-powered type Z
• 2 remote, wireless indoor/outdoor warning devices supported: models PGX901 (indoor), PGX911 (outdoor) (X=4, 8, or 9)
• Programmable as steady, pulsed or temporal three (as per ISO8201) and temporal four (CO alarm) output
• Warning device sounds alarms in the following priority: fire, CO, burg

Memory

• CMOS EEPROM memory

• Retains programming and system status on AC or battery failure for 20 years min. (not verified by UL)
  Power Supply- North America
  Transformer: DSC PTD1640U, PTD1640
  Primary: 120V, 60Hz Class II
  Secondary: 16.5VAC, 40VA Max.
  Power Supply – International

• Input ratings: 220V-240Vac, 50/60Hz, 200mA

• Transformer required, mounted in the same enclosure, permanently connected

• Transformer secondary ratings: 16.5Vac, 40VA min.
  Note: For installations using the transformer mounted inside the cabinet, replace fuse only with the same type (20mm) rated 250V /315mA.
  Regulated power supply:

• 1. 7 A regulated, supervised and integral to the control unit

• Type A as per EN50131-6 Standard

• 700mA auxiliary supply, 12V DC

• Positive temperature coefficient (PTC) for Bell, Aux+ and Battery terminals

• Reverse battery detection/protection

• Supervision for AC power and low battery

• Normal and high current battery charge options

• Supervised battery charging circuit
  Current draw (panel):

• 85mA (nominal) 2A(Max)
  Bell Output:

• 12V, 700mA supervised (lk Ohm) bell output (current limited at 2 amps)

• Steady, Pulsed, Temporal 3 fire, Temporal 4 CO alarm cadences

• Bell short detection (software+ hardware)

• Voltage range= 9.6V-13.8V DC

• Current= 700mA (shared with Corbus R(ed))

• Output ripple voltage: 270mVp-p max.

• Onboard programmable outputs:

• PGM 1- 50mA switched programmable output

• PGM 2-300mA current-limited switched programmable output. 2-Wire smoke detectors (90mA current limited) are supported using this PGM

• PGM 3-50mA switched programmable output

• PGM 4- 50mA switched programmable output

• Hardware PGM over current protection

Battery

• 12V sealed lead acid, rechargeable

• Battery capacity:

• 4 hours (UL commercial burglary/residential burglary),

• 12 hours (EN50131),

• 24 hours (UL/ULC resi fire, ULC com burglary, ULC com fire monitoring – no bell load allowed); INCERT [Belgium])
  Note: For T 014 compliance (INCERT certification), only 14Ah (2x7Ah) batteries were tested and are accepted for INCERT certified systems.

• Maximum standby time: 24 hours (with 14Ah battery and Aux current limited to 470mA)
  Recharging time to 80% 72 hours
  Recharging rate: 240mA (12 hours max.), 480mA (24 hour backup)

• Backup time: 24 hours (UL)

• Battery lifespan: 3-5 years

• Low battery trouble indication threshold 11.5VDC

• Battery restore voltage 12.5V

• Main board current draw (battery only):

• HS2016/32/64/128 (no alternate communicator) standby 85mA DC

• HS2016/32/64/128, (including alternate communicator) standby 190mA DC

• Transmit (alternate communicator module) 195mA DC

• Resettable fuses (PTC) used on circuit board

• Supervision for loss of primary power source (AC fail), battery loss or battery low voltage (battery trouble) with indication provided on the keypad

• Internal clock locked to AC power frequency

Operating Environmental Conditions

• Temperature range: UL= 0°C to +49°C (32°F-120°F),
• Relative humidity: <93% non condensing

Alarm Transmitter Equipment (ATE) Specification

• Digital dialer integral to the main control board
• Supports SIA and Contact ID
• Complies with TS203 021-1, -2, -3 Telecom equipment require­ ments and EN50136-1-1, EN50136-2-1, EN50136-2-3 ATS 2
• Optional Dual IP/Cellular communicators (3G2080(R)/ TL2803G (R)/ TL280(R)) can be installed in the same enclosure and con­ figured as primary or back-up, with AES 128-bit encryption
• Compliant with EN50136-l-1, EN50136-2-1 ATS2 requirements

System Supervision Features
The PowerSeries Neo continuously monitors a number of possible trouble conditions and provides audible and visual indication at the keypad.
Trouble conditions include:

• AC power failure
• Zone trouble
• Fire trouble
• Telephone line trouble
• Communicator trouble
• Low battery condition
• RF jam
• AUX power supply fault
• Failure to communicate
• Module fault (supervisory or tamper)

Additional Features

• 2-way wireless device support
• Visual verification (images + audio)*
• Proximity tag support
• PGM scheduling
• Quick arming
• User, partition, module, zone and system labels
• Soak test*
• Programmable system loop response
• Keypad and panel software versions viewable through keypad
• Doorbell zone type
• Low battery PGM type
  *Feature not evaluated by UL/ULC.

Programming Directory

This section provides a list of all available programming options in numerical order. To program, access Installer Programming mode by keying in [] [8] [Installer Code]. Use the scroll keys<> to navigate through the menus or jump directly to a specific section  by keying in a section number and pressing []. Programming consists of toggling on and off options in each section or by populating data fields. Press [*] to select options and [ #] to exit to the previous menu. For descriptions of all programming options and  programming worksheets, refer to the PowerSeries Neo Reference Manual .V= Default

Label Programming

000 Label Programming
000 – Language Selection (01)
001 –Zone Labels
001-128 -Zone Labels 1-128
051-Zone Tamper Label
052 -Zone Fault Label
064 –CO Alarm Message
065 -Fire Alarm Message
066 – Fail to Arm Event Message
067 -Alarm When Armed Event
Message
100 — System Label
101-108 –Partition 1-8 Labels
201- 208 — Partition 1-8 Command
Output Labels
001-004 – Command output 1-
4 Labels
601-604 Schedule 1- 4 Labels
801 –Keypad Labels
001-016 Keypad 1-16 Labels
802 –Zone Expander Labels
001-015 –Zone Expander 1-
15 Labels
803 — Output Expander Labels
001 Output Expander 1 Label
806 — HSM2HOST Label
808 –HSM2955 Label
809 –Power Supply Label
001-004 Power Supply 1-4
Label
810-High Current Output Supply
Label
001-004 Power Supply 1-4
Label
815 -Alternate Communicator
Label
820 — Siren Label
001-016 Siren 1-16 Label
821 — Repeater Label
001-008 Repeater 1-8 Label
999 — Default Labels
Zone Type
001 Zone Type
001-128 Zone Types (000)
000 — Null Zone
001-Delay 1
002 -Delay 2
003 –Instant
004 Interior
005 — Interior Stay/Away
006 -Delay Stay/Away
007 Delayed 24-Hour Fire
008 — Standard 24-Hour Fire
009 — Instant Stay/ Away
010 – Interior Delay
011 — Day Zone
012 – Night Zone
016 — Final Door Set
017 -24- Hour Burglary| 018 — 24-Hour Bell/Buzzer
023 -24- Hour Supervisory
024 24- Hour Supervisory
Buzzer
025 -Auto Verify Fire
027 – Fire Supervisory
040- 24-Hour Gas
041 –24-Hour CO
042- 24-Hour Holdup
043 — 24-Hour Panic
045 – 24- Hour Heat
046 –24- Hour Medical
047 -24-Hour Emergency
048 – 24- Hour Sprinkler
049 – 24- Hour Flood
051 –24- Hour Latching
Tamper
052- 24-Hour Non-Alarm
056–24- Hour High
Temperature
057 – 24 Hour Low
Temperature
060 — 24-Hour Non-Latching
Tamper
066 — Momentary Keyswitch
Arm
067 – Maintained Keyswitch
Arm
068 –Momentary Keyswitch
Disarm
069 –Maintained Keywsitch
Disarm
071 –Doorbell Zone
072– Push to Set
02 — Zone Attributes
001-0128 (see PowerSeries Neo
reference manual for defaults)
1- Bell Audible
2 – Bell Steady
3- Door Chime
4-Bypass Enabled
5 -Force Arm
6- Swinger Shutdown
7 Transmission Delay
8– Burglary Verification
9-Normally Closed EOL
10- Single EOL
11- Double EOL
12- Fast Loop/Normal Loop
Response
13 -Zone 2-way Audio
Activation
14- Holdup Verification
System Times
005 System Times
---|---
000 — System Area
Bell Cutoff (004 min.)
Bell Delay Time (000 min.)
Burglary Verification Timer
(060 sec.)
Holdup Verification Timer
(008 sec.)
Zone Loop Response (250 ms)
Automatic Clock Adjust (060
sec.)
001 — 008 System Times – Partition
1-8
Entry Delay 1 (030 sec.)
Entry Delay 2 (045 sec.) (CP-
01 030 sec.)
Exit Delay (120 sec.) (CP-01
060 sec.)
Settle Delay (010 sec.) ( CP-
01 000 sec.)
900 — Bell Delay Partition Mask
(Y,Y,Y,Y,Y,Y,Y,Y)
901 — Daylight Savings Begin:
Month (003)
Week (002)
Day (000)
Hour (002)
Increment (001)
902 Daylight Savings End
Month (011)
Week (001)
Day (000)
Hour (002)
Decrement (001)
Access Codes
006 Installer Defined Access Codes
(4-digit decimal)
001 -Installer Code (555555)
002 –Master Code ( 123456)
003 -Maintenance Code
(AAAA00)
004 – Guard Code (AAAA00)
PGM Programming
007 -PGM Programming
000 -Main Bell Partition
Assignment
1 – Partition 1
2-Partition 2
3-Partition 3
4Partition 4
5- Partition 5
6- Partition 6
7Partition 7
8-Partition 8
001-164-PGM 1-164 Partition
Assignment ( default: partition 1)
1-8– Partition 1-8
008 — PGM Timer Programming
000 -PGM Timer-Minutes or
Seconds (seconds)
001-164-PGM 1-164 Timer (005)| 009 –PGM Types
001-164-PGM 1-164 Type
Assignment (default: PGM1=121,
PGM2=156, 3-164=101)
100 — Null PGM
101 — Burg and Fire Bell
Follower
102-Delayed Fire and Burg
103 – Sensor Reset [][7][2] 104 -2- Wire Smoke
109- Courtesy Pulse
111– Keypad Buzzer Follow
114-Ready To Arm
115 – System Armed Status
116-Away Armed Status
117 – Stay Armed Status
120-Away Armed with no
Zone Bypass Status
121 –Command Output 1
122- Command Output 2
123-Command Output 3
124 – Command Output 4
129 — Partition Status Alarm
Memory
132 — Holdup Output
134 –24Hr Silent Input
135 — 24Hr Audible Input
146-TLM and Alarm
147 Kissoff
148 — Ground Start
149 — Alternate
Communicator
155 – System Trouble
156 – Latched System Event
157 System Tamper
161 -DC Trouble
165 Prox Used
175 — Bell Status and
Programming Access Output
176 — Remote Operation
184 — Open After Alarm
200- Zone Follower
201 — Follower-Zones 1-8
202 — Follower-Zones 9-16
203 — Follower-Zones 17-24
204 – Follower-Zones 25-32
205 – Follower-Zones 33-40
206- Follower-Zones 41-48
207 Follower-Zones 49-56
208 – Follower-Zones 57-64
209 –Follower-Zones 65- 72
210 — Follower-Zones 73-80
211 — Follower-Zones 81-88
212- Follower-Zones 89-96
213 – Follower-Zones 97-104
214 – Follower-Zones 105-112
215 — Follower-Zones 113-120
216 – Follower-Zones 120-128
010 PGM Attributes
000- Main Bell Mask
Fire Alarm
= Default
---|---
CO Alarm
Burglary Alarm
24-Hour Flood Alarm
Bell Squawks
001-164 PGM 1-164 Attributes
100-Null PGM
101 – Fire and Burglary
01 — True Output
03 — Code Required
102– Delay Fire and Burglary
01 – True Output
103 — Sensor Reset [][7][2] 03 — Code Required
109 — Courtesy Pulse
01 –True Output
111–Keypad Buzzer Follow
01 -True Output
02 – Timed Output
09 – Entry Delay
10 -Exit Delay
11-Door Chime
12-Keypad Buzzer Zone
13 — Audible Exit Fault
14 -Auto-Arm Pre-Alert
114- Ready To Arm
01 — True Output
115 -Armed Status
01 –True Output
116-Armed Away Mode
01 — True Output
117 -Armed Stay Mode
01 –True Output
121- 124 – Command Output 1-4
01 — True Output
02- Timed Output
03 — Code Required
(NZ off)
129 — Partition Status Alarm
Memory
01 –True Output
132 – Holdup Output
01 –True Output
02- Timed Output
146 – TLM and Alarm
01 — True Output
147 Kissoff Output
01 — True Output
148 -Ground Start
01 –True Output
149 -Alternate Communicator
01 –True Output
02-Timed Output
04Fire Alarm
05 -Panic Alarm
06 – Burglary Alarm
07 – Open/Close
08 –Zone Auto Bypass
09 –Medical Alarm
10 –Burglary Verified
11- Open after Alarm
12- Emergency Alarm
13 — Duress Alarm
14-Holdup Verified
155 — System Trouble
01 — True Output
02 – Timed Output
04 Service Required | 05 -Loss of Clock
06 -AC Fail
07 –DC Fail
08 –TLM
09 –FTC
10 – Ethernet
11-Zone Fault
12-Zone Tamper
13 — Zone Low Battery
156 — Latched System Event
01 -True Output
02 -Timed Output
04 -Fire Alarm
05 –Panic Alarm
06 -Burglary Alarm
07 Medical Alarm
08 — Supervisory
09 –Priority Event
10 — Holdup
11-Duress
12-Emergeney
13 – Fire Supervisory
14 -Fire Trouble
15 –CO Alarm
157 — System Tamper
01 -True Output
02 -Timed Output
09 –Module Tamper
10 -Zone Tampers
161 -DC Trouble
01 -True Output
02 -Timed Output
09 — Battery Low
10 –Battery Absent
165 -Prox Used
01 -True Output
175 – Bell Prog Access
01 –True Output
176 — Remote Operation
01 –True Output
184-Open After Alarm
01 –True Output
02 -PGM Timer
201- 216 Zone Follow Zones 1-128
01 – True Output
02 -Timed Output
09-016-Zone Terminal 1-16
011 PGM Configuration Options
001-164-PGM 1-164
Configuration
Zone Follower by Zone
Proximity Tag Used
Command Output Schedules
012 System Lockout (attempts/min.)
Keypad Lockout Attempts
(000)
Keypad Lockout Duration
(000)
Remote Lockout Attempts
(006)
Remote Lockout Duration
(060)
System Options
013 System Options 1
I–NC Loop/EOL
2-DEOL/SEOL
---|---
3- Show All Troubles when Armed ti/
4 -Tamper/Faults Do Not show as open
5 -Auto-Arm Schedule in [][6]
6- Audible Exit Fault V
7 – Event Buffer Follows Swinger
8 -Temporal Three Fire Signaling
014 System Options 2
1– Bell Squawk
2-Bell Squawk Auto-Arm
3- Bell Squawk on Exit
4-Bell Squawk on Entry
5- Bell Squawk on Trouble
6- Not Used
7Exit Delay Termination
8 – Fire Bell Continues
015 System Options 3
I-[F] Key V
2-[P] Key Annunciation
3-Quick Exit
4- Quick Arming/Function Key
5-Not Used
6– Master Code Not User
Changeable
7 -Telephone Line Monitor
Enable V
8 – TLM Audible When Armed
016 System Options 4
I- AC Trouble Display V
2-AC Trouble Light Flashes
3-Keypad Blanking
4-Keypad Blanking Requires
Code
5- Keypad Backlighting V
6-Power Save Mode
7-Bypass Display When Armed
8–Keypad Tampers Enabled
017 System Options 5
1 – Chime On Opening
2-Chime On Closing
3-RF Jam Audible
4- Multi-Hit
5-Late to Close
6– Daylight Savings Time
7Not Used
8- Bell Squawk on Away
Arm/Disarm Only
018 System Options 6
I- Test Transmission Exception
2- Real- Time Bypass Reporting
3–Not Used
4-Not Used
5-Keypad Buzzer Alarm
6- Not Used
7Exit Delay Restart (CP-01 V)
8–AC Fail Trouble Beeps
019 System Options 7
1 – Audible Wireless Zone Fault
2-Latching Troubles
3-Not Used
4-R-Button
5– Audible Bus Fault
6 – Duress Codes| 7Temperature in Celsius ti/
8-Reset After Zone Activation
020 System Options 8
1 – Access Code Entry During
Entry Delay
2 -EU Entry Procedure
3 – [][8] Access While Armed
4 Remote Reset
5- Engineer’s Reset
6- Keyswitch Disarming During
Entry Delay
7Installer Access and DLS
8- Troubles Inhibits Arming
021 System Options 9
I-Trbl Display
2-Keypad Blanking while armed
3 -Auto-Arming Bypass
4- Ready Display
5-PGM Keypad Blanking
6- Armed Display
7–Open Cancels Arming
8– Audible Exit Delay for Stay
Arming
022 System Options 10
1 – [F] Key Option
2-Not Used
3–Not Used
4 -Test Transmission Counter in Hours
5 -Away to Stay Toggle
6-2-Way Full Duration V
7 – Trouble Beeps Are Silent
8-Keyswitch Arms in Away Mode
023 System Options 11
1Ready LED Flash for Force Arm
2-Not Used
3 -Tamper/Fault Detection
4 -Access Code Required for [] [ 1] 5 -Access Code Required for [] [2] 6 -Access Code Required for [] [3] 7 -Access Code Required for[] [4] 8 – [][6] Accessibility
024 System Options 12
1- 50Hz AC/ 60 Hz AC (ARG )
2-Crystal Timebase
3 -AC/DC Inhibits Arming
4- Tamper Inhibit Arm
5-Real Time Clock Option
6-Not Used
7 – Option 7 (AC Brownout
Detection) This option must be
enabled for UL/ULC Commercial
Fire Installations.
8-DLS Disconnect
025 System Options 13
1 -European Dial(ARG V)
2-Force Dial V
3 -Test Transmission Counter in
Minutes
4-Not Used
V= Default
---|---
5 -ID Tone
6-Tone Generated-2100Hz
71 Hour DLS Window
8-FTC Audible Bell
040 User Authentication
01 — User Code or Proximity Tag
02 – User Code and Proximity Tag
041 Access Code Digits
00 -4-Digit Access Codes
01 –6-Digit Access Codes
042 Event Verification
01 – Burglary Verified Counter
(002)
02-Holdup Counter (002)
03 -Burglary Verification
Selection
001 -Police Code
002 – Cross Zoning
003 -EU Sequential
Detection
151-158 Partition 1-8 Auto­
Arm/Disarm
001 -Auto-Arming Times (9999)
24-Hour
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
002 — Auto- Disarm Times (9999)
24-Hour
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
003 — Auto- Disarming Holiday
Schedule
Holiday 1
Holiday 2
Holiday 3
Holiday4
004 -Auto-Arming Pre-Alert
(004)
005 -Auto-Arming Postpone
Timer (000)
006-No Activity Arming Timer
(000)
007 – No Activity Arming Pre­
Alert Timer (001)
200 Partition Mask
001 –Partition I to 8 Enable Mask
I -Partition I V
2-Partition 2
3-Partition 3
4-Partition 4
5-Partition 5
6- Partition 6
7Partition 7
8– Partition 8| 201-208 Partition 1-8 Zone
Assignment
001 -Zone 1-8
002 –Zn 9-16
003 –Zn 17-24
004 -Zn 25-32
005 –Zn 33-40
006 –Zn 41-48
007 -Zn 49-56
008 –Zn 57-64
009 -Zn 65- 72
010 –Zn 73-80
011 – Zn 81-88
012 Zn 89-96
013-Zn97-104
014-Zn 105-112
015 –Zn 113-120
016-Zn 121-128
300 Panel/Receiver Communications Path
001 — 004 Receiver 1-4
01 -Phone Line V
02 — AIt Comm Auto Routing
03 – Alt Comm Rec 1- E thernet
04 – Alt Comm Rec 2­ Ethernet
05 -Alt Comm Rec 3­ Cellular
06 -Alt Comm Rec 4­ Cellular
301 Phone Number Programming
001 — 004 Phone Nwnber 1 -4
Programming (DFFF … 32-digit)
304 Call Waiting Cancel String
(DB70EF)
Event Reporting
307 Zone Reporting
001-128 Zone Reporting for Zones
1-128
01 –Alarm
02 – Alarm Restore
03 –Tamper
04 -Tamper Restore
05 – Fault
06 -Fault Restore
308 Event Reporting
001 -Miscellaneous Alarm 1
01 — Duress Alarm
02–Opening After Alarm
03 — Recent Closing Alarm
04 – Zone Expander
Supervisory Alarm
05 -Zone Expander
Supervisory Alarm Restore

06 – Burglary Verified
07 – Burg Not Verified Alarm

08 — Alarm Cancel
002 – Miscellaneous Alarm 2
01 –Holdup Verified Alarm
V
011 — Priority Alarms
01 – Keypad Fire Alarm-F Key
02 -Keypad Fire Restore
---|---
03 –Keypad Medical Alarm­
MKey
04 -Keypad Medical Restore

05 — Keypad Panic Alarm (P)

06 –Keypad Panic Restore
07 – Auxiliary Input Alarm

08 –Aux Input Alarm Restore

021 – Fire Alarms 1
03 –PGM22-Wire Alarm
04-PGM 2 2-Wire Restore

101 — Tamper Events
03 –Module Tamper V
04 -Module Tamper Restore

05 –Keypad Lockout
07 Remote Lockout
201 — Open/Close Events 1
01 — User Closing
02-User Opening
03 – Future Use
04 -Future Use
05 — Special Closing
06 — Special Opening
07 Keyswitch Opening
08 — Keyswitch Closing
202 — Open/Close Events 2
01 — Automatic Closing
02 — Automatic Disarm
03-Auto Arm
Cancellation/Postpone
211 — Miscellaneous Open/Close
Events
01 — Late to Close
02- Late to Open
05 – Exit Fault
221 — Bypass Events
01 — Auto Zone Bypass
02 – Auto Zone Unbypass
03 -Partial Closing
301 — Panel Events 1
01 — Panel AC Fail Trouble

02 – Panel AC Fail Restore

03 –Panel Low Battery
04 -Panel Low Battery
Restore
05 –Panel Battery Absent
06 –Panel Battery Absent
Trouble Restore
302 – Panel Events 2
01 –Bell Circuit Trouble
02-Bell Circuit Restore
03 -Telephone Line Trouble

04-Telephone Line Trouble
Restore
05 – Auxiliary Trouble
06 -Auxiliary Trouble
Restore
305 — Panel Events 5| 03 -PGM 2 2-Wire Trouble

04 -PGM 2 2-Wire Restore

311 — Maintenance Events 1
01 –RF Jam Trouble
02-RF Jam Trouble Restore

03 –Fire Trouble
04 Fire Trouble Restore
05 –Cold Start
06 — Delinquency
07 – Self Test Trouble
08 — Self Test Trouble
Restore
312– Maintenance Events 2
01 –Installer Lead IN
02 — Installer Lead OUT
03 -DLS Lead IN
04–DLS Lead OUT
05 –SA Lead IN
06 –SA Lead OUT
07 – Event Buffer 75% Full

313 – Maintenance Events 3
01 – Firmware Update Begin

02 – Firmware Update
Success
03 –Firmware Update Fail
314 – Maintenance Events
01 –Gas Trouble
02–Gas Trouble Restore
03 –Heat Trouble
04 -Heat Trouble Restore
05 — Freeze Trouble
06 –Freeze Trouble Restore
07 Probe Disconnected
08 –Probe Disconnect Restore
321 — Receiver Events
02– Receiver 1 FTC Restore
04 – Receiver 2 FTC Restore
06 — Receiver 3 FTC Restore
08 -Receiver 4 FTC Restore
331 — Module Events 1
01 –Module AC Trouble
02– Module AC Trouble Restore
03 – Module Battery Trouble
04 – Module Battery Trouble Restore
05 – Module Battery Absent
06 –Module Battery Absent Restore
332-Module Events 2
01 –Module Low Voltage
02 – Module Low Voltage Restore
03 — Module Supervisory
V= Default
---|---
04 -Module Supervisory
Restore
05 — Module Aux Trouble
06 -Module Aux Trouble
Restore
335 — Module Events 5
01 — Output 1 Fault t/
02- Output 1 Fault Restore
351 — Alternate Communicator 1
01 — Alt. Comm. Module
Comm Fault
02 – Alt. Comm. Module
Comm Fault Restore
07 – Alt. Comm. Radio/SIM Failure
08 – Alt. Comm. Radio/SIM Failure V Restore
352 — Alternate Communicator 2
01 — Alternate Comm.
Network Fault
02 -Alt. Comm. Network
Fault Restore
05 -Alt. Comm. Ethernet
06-Alt. Comm. Ethernet
Trouble Restore
354 — Alternate Communicator 4
01 — Alt. Comm Receiver 1

02 – Alt. Comm Receiver 1
Restore
03 – Alt. Comm Receiver 2

04 — Alt. Comm Receiver 2
Restore
05 — Alt. Comm Receiver 3

06 — Alt. Comm Receiver 3
Restore
07 – Alt. Comm Receiver 4

08 – Alt. Comm Receiver 4
Restore
355 –Alternate Communicator 5
01 -Alt. Comm Receiver 1
Supervision Failure
02– Alt. Comm Receiver 1
Supervision Failure Restore

03 — Alt. Comm Receiver 2
Supervision Failure
04 -Alt. Comm Receiver 2
Supervision Failure Restore

05 — Alt. Comm Receiver
Supervision Failure
06 –Alt. Comm Receiver
Supervision Failure Restore

07 – Alt. Comm Receiver
Supervision Failure
08 — Alt. Comm Receiver
Supervision Failure Restore

361 -Wireless Device Events
01 — Device AC Fail t/
02-Device AC Restore | 03 — Device Low Battery
04 -Device Low Battery
Restore
05 -Device Fault
06 – Device Fault Restore
401- System Test Events
01 – Walk Test Start
02 Walk Test End
03 – Periodic Test
Transmission
04 – Periodic Test
Transmission with Trouble
05 — System Test
Communications
309 System Call Direction
001- Maintenance Events
I- Receiver 1 t/
2- Receiver 2
3- Receiver 3
4- Receiver 4
002 – Test Transmission Events
I-Receiver I
2-Receiver 2
3- Receiver 3
4Receiver 4
310 Account Codes
000 — System Account Code
(FFFF)
001-008 — Partition 1-8 Account
Code (FFFF)
311-318 Partition 1-8 Call Direction
001 — Partition Burglary
Alarm/Restore Call Direction
1-Receiver I
2- Receiver 2
3- Receiver 3
4Receiver 4
002 –Partition Tamper/Restore
Call Direction
1-Receiver I
2– Receiver 2
3 – Receiver 3
4Receiver 4
003 — Partition Opening/Closing
Call Direction
I- Receiver I
2 – Receiver 2
3- Receiver 3
4- Receiver 4
350 Communicator Formats (04 – SIA)
001- Communicator Format ­ Receiver 1
002- Communicator Format ­
Receiver 2
003- Communicator Format ­
Receiver 3
004- Communicator Format ­
Receiver 4
377 Communication Variables
001 – Swinger Shutdown Attempts
-Alarms and Restore (003)
(CP-01 002 sec.)
Tampers and Restore (003)
– Maintenance and Restore
(003)
002 — Communication Delays
---|---
– Zone Delay (000 sec.)(CP-
01 030 sec.)
– AC Failure Communication
Delay (030 min./hrs.)
TLM Trouble Delay (010
sec. x 3)
WLS Zone Low Battery
Transmission Delay (007
days)
– Delinquency Transmission
Delay (030 hours/days)
– Communications Cancel
Window (000 min.) (CP-01
005 sec.)
003 — Periodic Test Transmission
Cycle (030 hrs./days)
004 — Periodic Test Transmission
Time of Day (9999)
011 -Maximum Dialing Attempts
(005)
012 -PSTN Delay (003 sec.)
013 -Delay Between Force
Attempts (020 sec.)
014 -Post Dial Wait for
Handshake (040 sec.)
015 -T-Link Wait for Ack (060
sec.)
016 IP/Cellular Fault Check
Timer (010)
380 Communicator Option 1
1 – Communications Enabled
2- Restore on Bell Timeout
3-Pulse Dialing
4Pulse Dial After 5th Attempt
5 – Parallel Communications
6– Alternate Dial
7 – Reduced Dialing Attempts
8- Activity Delinquency
381 Communicator Option 2
1 – Keypad Ringback
2- Bell Ringback
4-Closing Confirmation
8 – Communications Priority
382 Communicator Option 3
2- Walk Test Communication
4-Call Waiting Cancel
5 – Alternate Communicator
Enable
6-AC Failure TX in Hours
8- Tamper Limit
383 Communicator Option 4
1-Phone Number Account Code
2-6-Digit Account Code
5-Communicate FTC Events
384 Communicator Backup Options
2-Backup Options – Receiver 2
V
3- Backup Options – Receiver 3
4-Backup Options – Receiver 4
385 Audio Module Talk/Listen Mask
I Talk/Listen on Phone Number
1
2-Talk/Listen on Phone Number
2
3 -Talk/Listen on Phone Number
3| 4-Talk/Listen on Phone Number
4
DLS Programming
401 DLS/SA Options
1-Double Call
2-User Enables DLS t/
3-DLS Callback
4- User Call Up
6 – Panel Call-Up and Baud Rate
7 – Alt. Comm DLS
402 DLS Phone Number
Programming (31-digit decimal)
403 DLS Access Code (default is
based on model)
HS2128 Models (212800)
HS2064 Models (206400)
HS2032 Models (203200)
HS2016 Models (201600)
404 DLS/SA Panel ID (default is
based on model)
HS2128 Models (2128000000)
HS2064 Models (2064000000)
HS2032 Models (2032000000)
HS2016 Models (2016000000)
405 PSTN Double Call Timer (060 sec.)
406 PSTN Number of Rings to
Answer On (000)
407 SA Access Code (FFFFFF)
410 Automatic DLS Options
001 – Automatic DLS Toggle
Options
1 -Periodic DLS
3-DLS on Event Buffer 75%
Full
5-SA on Event Buffer 75%
Full
8-DLS On Programming
Change
002- Periodic DLS Days (000
days)
003 — Periodic DLS Time (0000)
007 – Delay Call Window
Delay Call Window Start
(0000)
– Delay Call Window End
(0000)
560 Virtual Inputs (000)
001 – 032 Virtual Input 1-32
Schedule Programming
601-604 Programming Schedule 1-4
101 — Interval 1 Start Time (0000)
102 — Interval 1 End Time (0000)
103 — Interval 1 Days Assignment
01- Sunday
02-Monday
03 -Tuesday
04 -Wednesday
05 -Thursday
06-Friday
07 – Saturday
104 – Interval 1 Holiday
Assignment
09 – Holiday 1
10 – Holiday 2
11- Holiday 3
12- Holiday 4
= Default
---|---
201 — Interval 2 Start Time (0000)
202 — Interval 2 End Time (0000)
203 — Interval 2 Days Assignment
01 — Sunday
02-Monday
03 -Tuesday
04- Wednesday
05 -Thursday
06-Friday
07 — Saturday
204 – Interval 2 Holiday
Assignment
09 – Holiday 1
10 — Holiday 2
11 – Holiday 3
12- Holiday 4
301 — Interval 3 Start Time (0000)
302 — Interval 3 End Time (0000)
303 — Interval 3 Days Assignment
01 — Sunday
02-Monday
03 -Tuesday
04- Wednesday
05 -Thursday
06-Friday
07 – Saturday
304 -Interval 3 Holiday
Assignment
09 – Holiday 1
10 — Holiday 2
11 – Holiday 3
12- Holiday 4 201 — Interval
2 Start Time (0000)
402 — Interval 4 End Time (0000)
403 – Interval 4 Days Assignment
01 — Sunday
02-Monday
03 -Tuesday
04- Wednesday
05 Thursday
06-Friday
07 – Saturday
404 – Interval 4 Holiday
Assignment
09 — Holiday 1
10-Holiday 2
11 –Holiday 3
12-Holiday 4
711- 714 Holiday Group 1-4
001 –099 Holiday Group 1-4 Date
1-99 (000000, MMDDYY)
Audio Station Programming
802 Audio Station Assignment
001 – 128 — Station Assignment 1 –
128 (00)
600–2-Way Audio Trigger Option
1
01 -Tampers
03 -[A] Key Alarm
04 -[P] Key Alarm
05 –Duress Alarm
06 — Opening After Alarm
07 Future Use
08 –Zone Supervision Alarm
603 -2-Way Audio Control Option 1
01 – Future Use| 02 –Listen to all zones /
Listen to zones in alarm
03 — Future Use
04 — Siren Active During 2-
Way Audio
05 -Hang- Up Auto Detection 06 — User Call-In
07 – Future Use
08 –2-Way Audio Initiated by
cs
605 –Record Options
01 -Audio Capture Enable
02 – Erase on FTC
606 -Audio Station Record
Control Option 1
01 -Audio Station 1 Record

02 – Audio Station 2 Record

03 — Audio Station 3 Record

04 -Audio Station 4 Record

610- Call Back/ Recovery
Window Duration (05)
611 — Call Back Acknowledge
code (9999)
612- Answering Machine Bypass
(00)
613 –Double Call Timer (030)
614 – Number of Rings to Answer
(00)
615 — Audio Duration (90 sec.)
616- Record Time (105 sec.)
617 –Erase Timer (15 min.)
606 –Audio Station Tamper
Option 1
01 -Audio Station 1 Tamper
02 — Audio Station 2 Tamper
03 — Audio Station 3 Tamper
04 – Audio Station 4 Tamper
Wireless Programming
804 Wireless Programming
000 — WLS Device Enrollment
Zones (3-digit decimal)
Zone Type (2-digit decimal)
Partition Assignment
Zone Label (LCD only)
WLS Keys
Partition Assignment
User Assignment
Sirens
Partition Assignment
Siren Label (LCD only)
Keypads
Keypad Assignment
Keypad Label (LCD only)
Repeaters
Repeater Label (LCD only)
001 – 128 – Configure Wireless
Zones
Refer to the installation instructions
provided with the HSM2Host for
more wireless programming
options.
---|---
850 Cellular Signal Strength
851 Alternate Communicator
Programming
Refer to the installation instructions
provided with the alternate
communicator for details.
Keypad Programming
860 Keypad Slot Number
861-876 Keypad Programming
000 — Keypad Partition Mask
00 — Global Keypad
01 -Partition I
02– Partition 2
03 – Partition 3
04 -Partition 4
05 –Partition 5
06 – Partition 6
07 Partition 7
08 -Partition 8
001 – Function Key 1 (03)
002 – Function Key 2 (04)
003 — Function Key 3 (06)
004 – Function Key 4 (22)
005 — Function Key 5 ( 16)
00-Null Key
02 – Instant Stay Arm
03-Stay Arm
04-Away Arm
05 – No Entry Arm
06 — Chime On/Off
07 – System Test
09 –Night Arm
12– Global Stay Arm
13 -Global Away Arm
14- Global Disarming
16 – Quick Exit
17Arm Interior
21-24- Command Output 1-4
29 — Bypass Group Recall
31 — Local PGM Activate
32 – Bypass Mode
33 – Bypass recall
34 User Programming
35 – User Functions
37 Time/Date Programming
39 – Trouble Display
40 – Alarm Memory
61-68 — Partition Select 1-8
011 — Keypad 1/0 (000)
012 — Local PGM Output Timer
Pulse Time (00 minutes)
Pulse Time (05 sec.)
021 — Keypad Option 1
I-[F] Key Enabled
2-[M] Key Enabled
3-[P] Key Enabled
4 – Display Code or X’s
022- Keypad Option 2
1-Local Clock Display
2-Local Clock Display 24 Hour
3–Auto Alarm Scroll
5-Power LED Option
6-Power LED AC Present
7 -Alarms Displayed if Armed
8-Auto Scroll Open Zones
023 — Keypad Option 3| 1-Armed LED Power Save*
2-Keypad Show Arm Mode
3-5th Terminal is PGM
Output/Zone
7Local Display of Temp.
8 -Low Temperature Warning
030-LCD Message (16 x 2 hex)
031-Download LCD Message
Duration (000)
041 — Indoor Temperature Zone
Entry (000)
042 — Outdoor Temperature Zone
Entry (000)
101-228 — Door Chime Sound-Zone
1-128
00 — Disabled
01 -6 beeps
02 -“Bing-Bong” Sound
03 -“Ding-Dong” Sound
04 -Alarm Tone
05 -Zone Name
899 Template Programming
5-Digit Template Code (5-digit
decimal)
-Central Station Telephone
Number (32-digit decimal)
– Central Station Account Code
( 4/6-digit decimal)
– Partition Account Code ( 4-digit
decimal)
– DLS Access Code (6-digit
decimal)
Partition Entry Delay (000-255
sec.)
Partition Exit Delay (000-255
sec.)
– Installer Code
System Information and
Testing
900 System Information
000 — Control Panel Version
001- 016- Keypad 1-16 Version
Info
101-116-8-HSM21081-16
Version Info
201-216-HSM2208 Version
Information
460 –Alternate Communicator
461 – HSM2HOST Version Info
481 – HSM2955 Version Info
501 – 504 HSM2300 1-4 Version
Info
521-524 HSM2204 1-4 Version
Info
901 Installer Walk Test
Module Programming
902 Add/Remove Modules
000 – Auto-Enroll All Modules
001 — Enroll Modules
002 – Slot Assignment
003 — Edit Module Slot Assignment
101 — Delete Keypads
102 — Delete HSM2108
103 — Delete HSM2208
106 –Delete HSM2HOST
108 — Delete HSM2955
109 – Delete HSM2300
= Default
---|---
110 — Delete HSM2204
903 Confirm Modules
000 – View All Modules
101 — Keypads
102 – HSM2108
103 -HSM2208
106 – HSM2HOST
108 –Confirm HSM2955
109 –HSM2300
110 – HSM2204
904 Wireless Placement Test
001-128-Placement Test Zones
1-128
521-528 — Placement Test
Repeaters 1- 28
551-566- Placement Test Sirens
1-16
601-632 — Placement Test
Wireless Keys 1-32
701- 716 — Placement Test
Wireless Keypads 1-16
912 Soak Test
000 — Zone Soak Test Duration
Default: 014):
001-128-Zone Soak Test – Zones
1-128
Battery Settings
982 Battery Settings
000- Panel Battery Settings
01-Panel High Charge
Current
010 – HSM2204 Battery Settings
01 – HSM2204 1 High Charge
Current
02 – HSM2204 2 High Charge
Current
03 –HSM2204 3 High Charge
Current
04 – HSM2204 4 High Charge
Current
020 –HSM2300 Battery Settings
01 – HSM2300 1 Charge
02- HSM2300 2 Charge
03 -HSM2300 3 Charge
04 — HSM2300 4 Charge
Defaults
989 Default Master Code
990 Installer Lockout Enable/Disable
991 Default Keypads
901-916 – Default Keypad 1-16
999 – Default all Keypads
993 Default Alt Comm
996 Default HSM2HOST
998 Default HSM2955
999 Default System

* Wireless keypads only
IMPORTANT- READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following license terms:
This Encl-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. (“DSC’), the  manufacturer of the integrated security sys terns and the developer of the software and any related products or components (“HARDWARE”) which You acquired.
If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not use, copy or install the

SOFTWARE PRODUCT. The SOFTWARE PRODUCT
includes computer software, and may include associated media, printed materials, and “online” or electronic documentation. Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed  to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract.  If You do not agree to the terms of this EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE This EULA grants You the following rights:
   (a) Software Installation and Use – For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
   (b) Storage/Network Use – The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation, terminal or other digital electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be used
   (c) Backup Copy- You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You  may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
   (a) Limitations on Reverse Engineering, Decompilation and Disassembly – You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the extent that such activity is expressly pertnitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written permission ofan officer of DSC. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute  reasonable measures to ensure compliance with the tenns and conditions of this EULA.
   (b) Separation of Components -The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.
   (c) Single INTEGRATED PRODUCT -If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
   (d) Rental – You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.
   (e) Software Product Transfer – You may transfer all of Your rights under this EULA only as part of a pennanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts,  the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of this EULA.
   If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.
   (f) Termination – Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply 0with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
   (g) Trademarks – This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.

3. COPYRIGHT – All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any  copies of the SOFTWARE PRODUCT, are owned by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in and to the content which may be accessed through use  of the SOFTWARE PRODUCT are the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content.
   All rights not expressly granted under this EULA are reserved by DSC and its suppliers.

4. EXPORT RESTRICTIONS – You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to Canadian export restrictions.

5. CHOICE OF LAW- This Software License Agreement is governed by the laws of the Province of Ontario, Canada.

6. ARBITRATION – All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s decision. The place of arbitration shall  be Toronto, Canada, and the installation manual of the arbitration shall be English.

7. LIMITED WARRANTY
   (a) NO WARRANTY -DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WTLL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE  UNINTERRUPTED OR ERROR-FREE.
   (b) CHANGES IN OPERA TING ENVIRONMENT – DSC shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC- SOFTWARE or HARDWARE PRODUCTS.
   (c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK – IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CADS5.00). BECAUSE SOME  JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
   (d) DISCLAIMER OF WARRANTIES – THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES  OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO ASSUME FORIT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
   (e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY – UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY,  BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.
   WARNING: DSC recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail  to perform as expected.

Zone Record

Zone
001| Label| Location| Type| Attribute| | Zane
002| label| Location| Type| Attribute
---|---|---|---|---|---|---|---|---|---|---
3| | | | | | 4| | | |
5| | | | | | 6| | | |
7| | | | | | 8| | | |
9| | | | | | 10| | | |
11| | | | | | 12| | | |
13| | | | | | 14| | | |
15| | | | | | 16| | | |
17| | | | | | 18| | | |
19| | | | | | 20| | | |
21| | | | | | 22| | | |
23| | | | | | 24| | | |
25| | | | | | 26| | | |
27| | | | | | 28| | | |
29| | | | | | 30| | | |
31| | | | | | 32| | | |
33| | | | | | 34| | | |
35| | | | | | 36| | | |
37| | | | | | 38| | | |
39| | | | | | 40| | | |
41| | | | | | 42| | | |
43| | | | | | 44| | | |
45| | | | | | 46| | | |
47| | | | | | 48| | | |
49| | | | | | 50| | | |
51| | | | | | 52| | | |
53| | | | | | 54| | | |
55| | | | | | 56| | | |
57| | | | | | 58| | | |
59| | | | | | 60| | | |
61| | | | | | 62| | | |
63| | | | | | 64| | | |
65| | | | | | 66| | | |
67| | | | | | 68| | | |
69| | | | | | 70| | | |
71| | | | | | 72| | | |
73| | | | | | 74| | | |
75| | | | | | 76| | | |
77| | | | | | 78| | | |
79| | | | | | 80| | | |
81| | | | | | 82| | | |
83| | | | | | 84| | | |
85| | | | | | OR6| | | |
87| | | | | | 88| | | |
89| | | | | | 90| | | |
91| | | | | | 92| | | |
93| | | | | | 94| | | |
95| | | | | | 96| | | |
97| | | | | | 98| | | |

Module Record

Wireless Device Record

Installer-Defined Access Codes

001 — Installer Code:|
---|---
002 — Master Code:|
003 –Maintenance Code:|

System Account Code

Locating Detectors and Escape Plan

The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke and CO alarms.
Smoke Detectors
Research has shown that all hostile fires in homes generate smoke to a greater or lesser extent. Experiments with typical fires in homes indicate that detectable quantities of smoke precede detectable levels of heat in most cases. For these reasons, smoke alarms should be installed outside of each sleeping area and on each storey of the home.
The following information is for general guidance only and it is recommended that local fire codes and regulations be consulted when locating and installing smoke alarms.
It is recommended that additional smoke alarms beyond those required for minimum protection be installed. Additional areas that should be protected include: the basement; bedrooms, especially where smokers sleep; dining rooms; furnace and utility rooms;  and any hallways not protected by the required units. On smooth ceilings, detectors may be spaced 9.lm (30 feet) apart as a guide. Other spacing may be required depending on ceiling height, air movement, the presence of joists, uninsulated ceilings, etc. Consult National Fire Alarm Code NFPA 72, CAN/ULC-S553-02 or other appropriate national standards for installation recommendations.

• Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke.
• Avoid areas with turbulent air flow, such as near doors, fans or windows. Rapid air movement around the detector may prevent smoke from entering the unit.
• Do not locate detectors in areas of high humidity.
• Do not locate detectors in areas where the temperature rises above 3 8°C (I00°F) or falls below 5°C (41°F).
• Smoke detectors should always be installed in USA in accordance with Chapter 11 ofNFPA 72, the National Fire Alarm Code: 11.5.1.1.

Fire Escape Planning
There is often very little time between the detection of a fire and the time it becomes deadly. It is thus very important that a family escape plan be developed and rehearsed.
Every family member should participate in developing the escape plan.
Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the escape routes from sleeping quarters.
Escape from a bedroom must be possible without opening the interior door.
Consider the following when making your escape plans:

• Make sure that all border doors and windows are easily opened. Ensure that they are not painted shut, and that their locking mechanisms operate smoothly.
• If opening or using the exit is too difficult for children, the elderly or han­ dicapped, plans for rescue should be developed. This includes making sure that those who are to perform the rescue can promptly hear the fire warning signal.
• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as training in its use.
• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in winter; outdoor furniture or equipment should not block exits.
• Each person should know the predetermined assembly point where everyone can be accounted for (e.g., across the street or at a neighbor’s house). Once everyone is out of the building, call the fire department.
• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings as this can waste valuable time. Once outside, do not re-enter the house. Wait for the fire department.
• Write the fire escape plan down and rehearse it frequently so that should an emergency arise, everyone will know what to do. Revise the plan as con­ ditions change, such as the number of people in the home, or if there are changes to the building’s construction.
• Make sure your fire warning system is operational by conducting weekly tests.
  If you are unsure about system operation, contact your installer.

We recommend that you contact your local fire department and request further information on fire safety and escape planning. If available, have your local fire prevention officer conduct an in-house fire safety inspection.

Carbon Monoxide Detectors
Carbon monoxide is colorless, odorless, tasteless, and very toxic, it also moves freely in the air. CO detectors can measure the concentration and sound a loud alarm before a potentially harmful level is reached. The human body is most vulnerable to the effects of CO gas during sleeping hours; therefore, CO detectors should be located in or as near as possible to sleeping areas of the home. For maximum protection, a CO alarm should be located outside primary sleeping areas or on each level of your home. Figure 5  indicates the suggested locations in the home.
Do NOT place the CO alarm in the following areas:

• Where the temperature may drop below -10°C or exceed 40°C
• Near paint thinner fumes
• Within 5 feet (1.5m) of open flame appliances such as furnaces, stoves and fire­ places
• In exhaust streams from gas engines, vents, flues or chimneys
• Do not place in close proximity to an automobile exhaust pipe; this will dam- age the detector

PLEASE REFER TO THE CO DETECTOR INSTALLATION AND OPERATING INSTRUCTION SHEET FOR SAFETY INSTRUCTIONS AND EMERGENCY INFORMATION.

Regulatory Approvals

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re-orient the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock# 004-000-00345-4.
IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this number must be provided to the Telephone Company.
HS2128 Product Identifier US: F53AL01BHS2128
REN: 0.lB
USOC Jack: RJ-3 lX
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACT A. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not  exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier  that has the format.
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Incidence of Harm
If this equipment HS20 l 6/HS2032/HS2064/HAS2 l 28 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone  Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the
Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
If trouble is experienced with this equipment HS2016/HS2032/HS2064/HAS21284 for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request  that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122 Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.
Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so,  alarm dialling equipment must be connected to a properly installed RJ-3 lX jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-3 lX jack and alarm dialling equipment for you.

INDUSTRY CANADA STATEMENT
NOTICE: This Equipment, HS2016/HS2032/HS2064/HAS2128, meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies  that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed five.
Certification Number:
IC: 160A-HS2128
This Class B digital apparatus complies with Canadian ICES-003.
UL/ULC Installations
This product has been tested and found in compliance with the following standards:

• ULl 610 Central-Station Burglar-Alarm Units

• UL365 Police Station Connected Burglar Alarm Units and Systems

• ULl 023 Household Burglar-Alarm System Units

• UL985 Household Fire Warning System Units

• UL1635 Digital Alarm Communicator System Units

• ULl 63 7 Home Health Care Signaling Equipment

• ULC-S304-06 Signal Receiving Centre & Premise Burglar Alarm Control Units

• ULC-S559-04 Equipment for Fire Signal Receiving Centers and Systems

• ULC-S545-02 Residential Fire Warning System Control Units

• ORD-Cl023-1974 Household Burglar-Alarm System Units
  This product has also been tested and found in compliance with the ANSI/SIA CP-01­ 2010 Control Panel Standard -Features for False Alarm Reduction.
  This product is UL/ULC listed under the following categories:

• AMCX/AMCXC Central Stations Alarm Units

• APA W Police-station-connected Alarm Units

• DA YRC Central Station Fire Alarm System Units

• UTOU/UTOUC Control Units and Accessories, Household System Type

• NBSX/NBSXC Household Burglar Alarm System Units

• AMTB Control Panels, SIA False Alarm Reduction
  The product is labeled with the UL and ULC listing marks along with the SIA CP-01 compliance statement (Also Classified in accordance with SIA-CP-01 Standard) as proof of compliance with the above mentioned standards. For further information on this product’s listings please also refer to the official listing guides published at the UL web site (www.ul.com) under Online Directions Section.
  UL/ULC Residential Fire and Burglary Installations:

For ULC Installations refer to the Standard for the Installation of Residential Fire Warning Systems, CAN/ULC-S540.

• All burglary-type zones shall be configured with SEOL or DEOL con­ figuration. Use model EOLR-2.  (refer to section [002], bit 10 or 11 shall be ON)
• Use at least one PG9926 or PG9916 Smoke Detector for Fire Installations (sec- tion [001), fire zone shall be programmed as type 025)
• The entry delay shall not exceed 45 seconds (refer to section [005])
• The exit delay shall not exceed 60 seconds (refer to section [005])
• The minimum Bell Time-out is 4 minutes (refer to section [005])

Note: For ULC Residential Fire Installations the minimum Bell Time-out is 5 minutes
For UL Home Health Care Installations the minimum Bell Time-out is 5 min.
For UL Commercial Burglary Installations minimum Bell Time-out is 15 min.

• Temporal Three Fire Signal shall be enabled (section [013], opt.8 ON)

• Arm/Disarm Bell Squawk shall be enabled when using wireless key PG4939, PG4929, PG4949 (section [014], option 1 shall be ON)

• A code shall be required for bypassing (section [023], option 4 shall be ON)

• Trouble beeps shall be enabled (section [022], option 7 shall be ON)

• AC trouble indication LED shall be enabled (Keypad Programming, section [022], options 5 and 6 shall be ON)

• DACT Communicator shall be enabled for Supervising Station Monitoring (section [380], option 1 shall be ON)
  Note: The DACT communicator for this product has no line security.

• Telephone Line Monitoring (TLM) shall be enabled (section [015], option 7 shall be ON)
  Note: This product is programmed to perform 5 (min.) to 10 (max.) attempts for communication of an event to the supervising station. If unsuccessful, a Fail To Communicate (FTC) trouble is generated.

• Test transmission cycle shall be set for monthly transmission (refer to section [351])
  Note: For ULC Residential/Commercial installations set for daily test transmission

• Wireless Supervision window shall be set to 4 hours for Fire Installations (Wireless Programming, section [804]>[802] shall be programmed with the value 16)

• Wireless Supervision window shall be set to 4 hours for Burglary Install­ ations only (Wireless Programming, section [804]>[802] shall be programmed with the value 96)

• RF Jam detection shall be enabled (refer to Wireless Programming (section [804][801], option 00 shall be OFF)

• New Alarms will Disconnect 2-way Audio (section [022], opt 6 OFF)

UL Central Station and Police Connect with Standard or Encrypted Line Security Service

• The installation must use the Models TL2803G(R) IP/3G Interface, 3G2080(R) 3G Interface or TL280(R) IP Interface, which communicates over Cellular Data Network or an Ethernet network 10/l00BaseT to the compatible Sur-Gard Sys­ tem I/II/III/IV  receiver.

• Polling time shall be 200 seconds and compromise detection time shall be 6 min.

• For Encrypted line security applications, the Models TL2803G(R) IP/3G Inter­ face, 3G2080(R) 3G Interface or TL280(R) IP Interface shall have the Encryp­ tion Key enabled (AES128 bit encryption algorithm is validated under NIST Certificate No.2645
  Wireless Supervision window shall be enabled (refer to Wireless Pro­ gramming, sections [804]>[802])
  UL Local, Central Station and Police Connect with No Line Security Service

• The installation shall use a Bell which is UL Listed for Mercantile local alarms. An example of a UL Listed bell that can be used is Amseco Model MBLl0B bell with Model AB-12 bell housing. Connections from the control unit to the bell shall be made in  conduit. (Optional for central Station)

• The bell timeout shall be programmed for 15 minutes minimum

• At least one system remote keypad with tamper switch shall be employed

• The integral DACT shall be enabled and shall be programmed to provide a low battery transmission

• The control panel shall be in the attack resistant enclosure. The separately lis­ ted CMC-1 or PC4050CA attack resistant enclosure shall be employed

• The maximum entry delay time shall not exceed 45s as a result of the attack test. The maximum exit delay time shall not exceed 60 s.

• A tamper switch shall be used to protect the enclosure cover of the control unit. A tamper switch shall also be used on the keypad rear to detect removal from the wall.

• 24 h check in transmission shall be enabled

• Open/Closing acknowledgement enabled.(Not Police Station)

• The Installation shall use the internal dialer (DACT) alone or in conjunction with Models TL2803G(R) IP/3G Interface, 3G2080(R) 3G Interface or TL280 (R) IP Interface, which communicates over Cellular Data Network or an Eth­ ernet network 10/1  00BaseT to the compatible Sur-Gard System /I/II/IV receiver.

UL Home Health Care Signaling Equipment

• There must be at least two keypads, one of either one of the compatible keypads models HS2LED, HS2LCD(P), HS2ICN(P), HS2LCDRF(P)9, HS2ICNRF(P)9 and HS2TCHP
• Each system shall be programmed to activate an audible Trouble signal within 90 seconds upon loss of microprocessor memory
• The HS2TCHP shall be used along with another compatible model keypad in order to provide audible supervision for homehealth care or medical installations.

ULC Central Station Fire and Burglary Monitoring Installations

• For installation requirements, levels of security, communication modules and configurations (Refer to the ULC Installation Information Sheet, DSC #29002157)
• Use a CSA/cUL approved transformer (hardwired connections required for Fire Monitoring)
• All tamper circuits may be connected to the same zone
• HS2TCHP touch screen keypad is for supplementary use only with ULC Commercial Fire Monitoring

Programming
The notes in the programming sections of the PowerSeries Neo Reference Manual describing the system configurations for UL/ULC listed installations shall be implemented.
Control of the Protected Premises
In order to have a UL certificated system, the protected area is to be under the responsibility of one ownership and management (i.e., one business under one name).
This may be a group of buildings attached or unattached with different addresses but under the responsibility of someone having mutual interest. The person of mutual interest is not the alarm-installing company.
Note: This does not apply to strip mall applications where each independent business must have their own separate alarm system.
e.g.,1: a commercial partitioned system that has an office and a warehouse area in a building where each area can be armed or disarmed independently.
e.g.,2: a residential system partitioned so that the garage area is armed separately from the house.
Each of the above examples is under the sole responsibility of a single owner. The bell and DACT power supply must be in a protected area including partitioned systems. The bell and DACT power supply must be located where it can be heard by the person or persons responsible for maintaining the security system during the daily arming cycle.

Bell Location
The alarm sounding device (bell) shall be located where it can be heard by the person operating the security system during the daily arming and disarming cycle.
Protection of the Control Unit

• The local control unit and the local power supply must be protected in one of the following ways:
• The control unit and audible alarm device must be in a protected area which is armed 24 hours a day.
• Each partition must arm the area protecting the control unit and the audible alarm device power supply. This may require duplicate protection armed by each partition. Access to this protected area, without causing and alarm, will require that all partitions  be disarmed.
• In all cases described above, the protected area for the control unit must be pro- grammed as not-bypassable.

Casual Users
The installer should caution the user(s) not to give system information (e.g., codes, bypass methods, etc.) to casual users (baby-sitters or service people). Only the One-Time Use codes shall be given to casual users.
User Information
The installer should advise the users and note in the User’s Manual:

• Service organization name and telephone number
• The programmed exit time
• The programmed entry time
• Test system weekly
• The installer code cannot arm or disarm the system

Aux Loading and Battery Selection

HS2128/HS2064/ HS2032/HS2016
Board current draw 85mA| UL Residential Burg ULC Residential Burg| UL Commercial Burg| UL Resi Fire
UL Home Health Care ULC Resi Fire
ULC Corn Burg| ULC Fire Monitoring| EN50131
Grade 2/Class II
---|---|---|---|---|---
Max AUX (NSC) current loading| 0.7A| 0.7A| 0.5A| 0.5A| 0.5A
Max BELL (Alarm) current loading| 0.7A| 0.7A| 0.7A| 0.7A (no local alarm notification allowed, only remote transmission to SRC)| 0.7A
UL/ULC Listed enclosure| pcsooc PC5003C| CMC-1 PC4050CAR| PC5003C| PC5003C
PC4050CR (red/transfomer mounted inside)| PC5003C Power UC I
Transformer requirements| 16.5V/40VA (plug in rYPe)
PTC1640U (USA) PTCI640C6 (CAN)| | | FTC1637 (cUL listed)
16.5V/37VA (Hardwired type, mounted inside the enclosure or outside using electrical box)| 16.5V/40VA
(hardwired type, mounted inside the cabinet)
Battery Capacity requirements| 7Ah| 7Ah| I 4Ah (2 x 7Ah in parallel)| 14Ah (2 x 7Ah in parallel)| 7Ah
Standby Time| UL: 4 hours ULC: 24 hours| 4 hours| 24 hours| 24 hours| 12 hours
Alarm time| 4 minutes| 15 minutes| 4 min (UL resi fire)
5 min (Home Health Care and ULC Resi Fire)| 5 minutes (Alarm Transmission only)| N/A
Recharging current setting| 400mA, 700mA| 400mA, 700mA| 400mA. 700mA| 400mA, 700mA| 400mA, 700mA

SIA False Alarm Reduction Installations: Quick Reference
Minimum required system consists of one Control unit model HS2128 or HS2064 or HS2032 or HS2016 and any one of the compatible listed keypads: HS2LCDRF9, HS2LCDRFP9, HS2ICNRF9, HS2ICNRFP9, HS2LCD, HS2LCDP, HS2ICN, HS2ICNP,  HS2LED HS2TCHP.
The following wireless keys can also be used in SIA compatible installations: PG9929, PG9939,PG9949.
Note: For models PG9929 and PG9939, the panic/emergency key shall be disabled for SIA compliant installations.
For a list of the default values programmed when the unit is shipped from the factory, and for any other programming information, refer to the following table.
The following optional subassembly modules also bear the SIA CP-01-2010 classification and may be used if desired: HSM2108 zone expander, HSM2208 PGM output module, HSM2300 auxiliary power supply, HSM2204 output module, HSM2HOST9 2-way  wireless transceiver, PG9901 indoor siren, PG9911 outdoor siren, and 3G2080(R)/ TL2803G(R)/ TL280(R) cellular and PSDN communication module.
Caution

• For SIA FAR installations use only modules/devices that are listed on this page.
• Fire Alarm Verification feature (Auto Verified Fire Zone type [025]) is not supported on 2-wire smoke detectors zones, model FSA-2 lOB(T) (S)(ST)(LST)(R)(RT)(RD)(RST)(LRST). This feature may be enabled for 4-wire smoke detectors only (FSA-410B(T) (S)(ST)(LST)(R)(RT) (RST)(LRST) and wireless detectors PG9916/PG9926). The fire alarm delay is 60s.
• Call Waiting Cancel (Section [382], Option 4) feature on a non-Call Waiting line will prevent successful communication to the supervising sta­tion.
• All smoke detectors on the system must be tested annually by conducting the Installer Walk Test. Prior to exiting walk test mode, a sensor reset must be done on the system, [*][7][2], to reset all latching 4-wire smoke detectors. Refer to the installation  instructions supplied with the detector for details.

Notes

• Programming at installation may be subordinate to other UL requirements for the intended application.
• Cross zones have the ability to individually protect the intended area ( e.g. motion detectors which overlap).
• Cross zoning is not recommended for line security Installations nor is it to be implemented on exit/entry zones.
• This control panel has a communication delay of 30 seconds. It can be removed or increased up to 45 seconds by the end user in consultation with the installer.
• The security system shall be installed with the sounding device activated and the communicator enabled for transmission using SIA or CID format.
• ULC commercial burglary installations require DEOL resistors.

SIA Feature Programming Section| Comments| Range/Default| Requirement
---|---|---|---
Exit Time [00511001], option 3| Access to Entry and Exit delays and Bell Time Out for the system.| Range:45- 255 seconds
Default: 60 sec.| Required (programmable)
Exit Delay Restart [018]. option 7| Opening a Delay zone door after it has already been opened and closed during an exit delay restarts the exit delay timer.| Default: Enabled| Required
Auto Stay Ann on Un-vacated Premises
[001]1001]4128] Zone type 05. 06,09| Function key: Forces the system to arm in Stay mode if the occupant does not exit the premises after pressing the Away function key.| If no exit after MI arm
Default: Enabled| Required
Exit Timc and Progress Annunciation/Disable or Remote Arming
[861]>[001]40051, option 4| System times and audible exit beeps can be disabled when using the wireless key to stay arm the system. When away arming, audible exit beeps can not be disabled.| Default: Enabled| Allowed
Entry delay(s)
(005]>1001]4008). options 1 and 2| Access to entry and exit delays and bell time out for the system
Note: Combined entry delay and communications delay (abort window) shall not exceed 60s.| Range: 30 sec. to 4 min.
Default: 30 sec.| Required (programmable)
Abort Window for Non-Fire zones (002]>[001]-(128], option 7 ON| Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone. May be disabled by zone or zone type.| Default: Enabled| Required
Abort Window Time – for Non- Fire zones
[377]>(002], option I| Access to the programmable delay before communicating alarms
Note: Combined entry delay and communications delay (abort window) shall not exceed 60 seconds.| Range: 00 – 45 sec. Default: 30 sees| Required (programmable)
Abort Annunciation| An audible tone is generated when an alarm is aborted during the abort window.| Hard-coded ON| Required
Duress Feature
[‘][51> mastcr code> user 2-95> 5> 2| When this feature is enabled, selected user codes send a duress reporting code to the central station when used to perform any function on the system. Section [019]. option [6] must be enabled.| Default: N| Required
Cancel Window [37711002], option 6| Access to the communications cancel window. Minimum duration must be 5 minutes.| Range: 005-255 Default: 005|
Cancel Annunciation [3081>[001], option 8| Access to the reporting code for Alarm Canceled.| A Cancel was transmitted
Default: Enabled| Required
Cross Zoning
(042]>Selcction 3, option 002| Enables cross zoning for entire system. Zones can be enabled for cross zoning via zone attribute option 8 in sections [002][101] – [128].| Programming required
Default: Disabled| Required
Burglary Verification Timer [00511000], option 3| Access to the programmable Cross Zone timer.| Range: 000-255 sec.
Default: 60 seconds| Allowed
Swinger Shutdown for Alarms (377]>(00l], option I| Access to the swinger shutdown limit for zone alarms For all non-fire zones, shut down at Ito 6 trips.| Default: 2 trips| Required (programmable)
Swinger Shutdown Enable (0021>[001]- (128], option 6 ON| Access to swinger shutdown, transmission delay and cross zone attributes. Zone attribute option 6 (Swinger Shutdown enabled) is ON.| Non-police response zones
Default: Enabled| Allowed
24-Hr. Auto-verified Fire
(0011>[001]-(128], Zone type 025 ON| Access to 24-Hr. Auto-verified Fire
Activates if Not restored within the specified time.| Must choose zone type for application| Required
Call Waiting Cancel [382]. option 4 OFF| Access to the dialing sequence used to disable call waiting. Call waiting string can be programmed in [304]| Depends on user phone line
Default: Disabled| Required
System Test:
[‘][6] Master Code, option 04| The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on. Refer to user manual (part no. 29008365).| |
Walk Test Mode: r][8][1nstaller code][901)| This mode is used to test each zone on the system for proper functionality.| |
Walk Test Communications [382], option 2| Enables communication of zone alarms while walk test is active.| Default: Disabled|
Walk Test Start/ End Reporting Codes
(308][401), options 1 and 2| Access to the reporting codes for walk test start and end times.

Limited Warranty

Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or ninety (90) days,  whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty period. There is absolutely no  warranty on software and all software products are sold as a user license under the terms of the software license agreement included with the product. The Customer assumes all responsibility for the proper selection, installation, operation and maintenance of  any products purchased from DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.

International Warranty
The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls must first obtain an authorization  number.
Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.
Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to normal use.
It does not cover:

• damage incurred in shipping or handling;
• damage caused by disaster such as fire, flood, wind, earthquake or lightning;
• damage due to causes beyond the control of Digital Security Controls such as excessive voltage, mechanical shock or water damage;
• damage caused by unauthorized attachment, alterations, modifications or for­ eign objects;
• damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.);
• defects caused by failure to provide a suitable installation environment for the products;
• damage caused by use of the products for purposes other than those for which it was designed;
• damage from improper maintenance;
• damage arising out of any other abuse, mishandling or improper application of the products.

Items Not Covered by Warranty
In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii) products which are not identified with DSC’s product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at DSC’s option.
Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid purchase order is received from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC’s Customer Service.
Digital Security Controls Ltd.’s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchaser’s time, the claims of third parties, including customers, and injury to property. The laws of some jurisdictions limit  or do not allow the disclaimer of consequential damages. If the laws of such a jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that the above may not apply to you.

Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada.
WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

Out of Warranty Repairs
Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number.
Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.
Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital Security Controls has predetermined and which may be revised from time to time, will be charged for each unit repaired.
Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of the replacement product will be charged for each replacement unit.

WARNING – READ CAREFULLY
Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system.
System Failures
This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately  or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be:
Inadequate Installation
A security system must be installed properly in order to provide adequate protection.
Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is  available.
Criminal Knowledge
This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected.
Access by Intruders
Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system.
Power Failure
Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be  charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system.
After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended.
Failure of Replaceable Batteries
This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life.
While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will keep the system in good operating condition.

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other countries]. Any misuse of the trademarks is strictly prohibited and Tyco will aggressively enforce its intellectual property rights to the fullest extent  of the law, including pursuit of criminal prosecution wherever necessary. All trademarks not owned by Tyco are the property of their respective owners, and are used with pennission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may vary from photos. Not all products include all features. Availability varies by region; contact your sales representative.

© 2015 Tyco Security Products
All Rights Reserved.
Tech Support: l-800-387-3630 (Canada & U.S.)
or 905-760-3000
www.dsc.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>