ihartan OEM-iHar-01 WiFi Extender User Guide

ihartan OEM-iHar-01 WiFi Extender

LED Descriptions

Method 1: Web UI

1. Power On Plug the Extender in an outlet near your router.

2. Connect to iHAR-2G/5G Go to your phone/PC WiFi Settings  age, wait for your device to  search and click to connect to the extender’s network IHAR-2G / iHAR-5G.
   (Ensure that the mobile data is disabled.)

3. Enter the LOG-IN Page After connecting to iHAR-2G/ iHAR-SG , the log-in page should pop up automatically. (If the log-in page doesn’t pop up, please launch a web browser and input 192.168.10.1 to enter.)

4. Login

   • Create your own login password to log in OR you may click to skip this part.

5. Extend Your WiFi Signal

6. Select the WiFi network you want to extend, enter the password of it and click Save Setting. (Be aware that your phone may automatically capitalize the first letter of your router password. Please make sure you input the correct password, otherwise there would be no internet connection and reset wlll be necessary.) 05

7. Connect to Extended WiFi Please do not close the page until the setup countdown finishes. After configuration, please go back to your phone/PC WiFi Settings and connect to the extended WiFi network with your router’s password.

   • Note: The extended WIFI name Is ”Your WIFI Name -2G” or “Your WiFi Name-5G”, e.g.,HQUSE 1-2G or HOUSE 1-5G When you complete the setup steps, please relocate the extender halfway between the router and the WiFi dead zone to get better signal.

Method 2 : WPS Button

Note: If you don’t have a WPS button on the router, please try method 1 to set up.

1. PowerOn Plug the Extender in an ouUet near your router.
2. Press 2 buttons to extend Prass the WPS button on the main router for 1-2 seconds, and press the WPS button on the extender for 1-2 seconds within 1 minute.

Connect to Extended WiFi

When configuration is successful (WPS LED changes from blinking to OFF), please go to your WiFi settings page to connect to the extended WiFi network “Your WiFi Name-2G/-5G” with your router’s password. If this method doesn’t work, please try Method 1 .

FAQ

• Will the extended network be secure?

• Yes. WiFi extenders offer the same levels of security as traditional WiFi routers (WEP, WPA, WPA2 etc), so don’t worry if it shows “unsecure” before setting up.

• The maximum range can this repeater extend?

• It can extend 2500 square feet theoretically when without any obstacle.

• Can it increase my network speed?

• Sorry, the extender is only used to extend the range of WiFi signal from your main router.
  How can I enter the login page?

• connect to the network iHAR-2G, launch your browser and enter 192.168.10.1 into the address field. Or you can connect the extender to your PC with an Ethernet port, then input 192.168.10.1 in your browser to enter the login page.

• It extends WiFi signal but with lower speed? A: Please place in halfway between your router and the WiFi dead zone. And please note that all WiFi extenders have some speed loss, but our product has been engineered to optimize this technical issue and minimize loss. Moreover, if the maximum WiFi speed of your main router is 800Mbps, then the extended network provided by the extender will be less than or equal to BOOM bps due to technical limitations and obstacles like thick walls and furniture in your house.

• No internet access after successful extension?

  • Check if the main router is working.
  • Confim1 whether the extension is successful. (Judge by the indicator lights on the extender)
  • Reset the extender and check if the password you entered for extended WiFi network during setup is correct. It should be the same as your router’s password.

• I put in a wrong password, how should I reset the extender?

• Use the pin provided in the packing box to insert the RESET hole for about 6 seconds till all lights are on again. And try method 1 to set up again.

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>