kmart 43055470 Noize Pro Scooter Instructions
- June 6, 2024
- Kmart
Table of Contents
NOIZE PRO SCOOTER INSTRUCTIONS
Keycode: 43055470
WARNING! Read the information supplied by the manufacturer.
WARNING! Assembly by an adult.
WARNING! Wear personal protective equipment. Always wear a helmet and
protective pads. Do not use a scooter at night. Do not use on wet surfaces,
uneven or unpaved roads. Do not use on public roads.
This scooter is not designed for off-road use.
Not suitable for children under 7 years old. User’s maximum weight: 100Kg.
This product complies with EN 14619 Class A.
Remove the scooter and all the parts from the box. Set out all the parts and read the assembly instructions prior to use. Keep the packaging until assembly is complete.
General instructions
- This scooter requires adult assembly. Prior to use, make sure that the scooter has been assembled properly. Due to the skill it requires, the scooter must be used with care in order to avoid falls or collisions likely to injure the user or others.
- For use with suitable protective equipment, including a helmet, closed shoes, elbow, wrist, and knee protection.
- This scooter is not a toy for children under the age of 7 years.
Riding Instructions
a) The scooter can be dangerous and can lead to a traffic accident when used
on public highways. Not to be used on public roads.
b) It is best used on a flat, clean surface, free of gravel and grease.
c) Avoid bumps and drainage grates that may cause an accident.
d) The scooter does not include any headlights or lights. It is therefore not
suitable for use at night or during periods when visibility is limited.
e) Do not allow more than one child to ride the scooter at the same time.
Before and after use
– Check all screws and fittings are secure before giving them to a child.
– Ensure all locking devices are engaged. Ensure there are no broken
components.
– Spin each wheel to make sure the wheel rotates smoothly indicating that the
bearings are undamaged.
Assembly Instructions:
- Loosen the clamp on the steering tube. Slide the tube onto the fork until it is touching the fork headset washers.
- Tighten the upper bolt one-quarter of a turn and the lower bolt one-quarter of a turn using the hex key provided. Repeat until the clamp is tight and the handlebars are secure.
- Make sure the wheel faces forward when the handlebars are held facing straight.
WARNING! Failure to tighten the clamp fully will result in the handlebars not being secure and the scooter will be unsafe to ride. Over tightening one bolt before the other will make it impossible to tighten the clamp fully.
Use
– Hold both handgrips firmly. Put one foot towards the front of the deck, push
off the ground to propel the scooter forward with the other foot. Both feet
can fit on the deck when the desired speed has been reached.
– Practice foot positioning at a slower speed until you build skill and
experience. Shifting your foot position or lifting or placing your feet while
traveling affects the stability of the scooter. You must learn to maintain
control while you move your feet on and off the deck of the scooter.
– Braking: Brake is located at the rear, when necessary, press down on it to
slow down. Press down gradually in order to prevent skidding or loss of
stability. The metal or aluminum brake may heat up after multiple uses. Avoid
touching it during and after use.
– Shoes are mandatory and we strongly advise you to wear long pants and long
sleeve shirts to avoid injury if you fall. Do not ride barefoot or with loose
fitting shoes, thongs or
sandals.
Care Instructions
A. Wheel bearings: Avoid going through water, soil, or sand as this can
damage wheel bearings.
To look after the wheel bearings, systematically check that the wheels turn
properly by turning the scooter upside-down and using your hand to spin the
wheels. If the wheels do not spin, they must then be removed to check their
condition. First, unscrew the wheel axle, remove the axle and detach the
wheel, then carefully push the two-wheel bearings out of their housing. If
they are chipped or dented, new ones should be bought. If there is no visible
damage, they must then be oiled. To do this, remove all traces of grease, mud,
or dust with a kitchen towel or cloth, and re-oil them with a grease spray or
by leaving them to soak overnight in oil [turn them several times in the oil
first]. Remove and reassemble the wheel bearings and axles, followed by the
wheel, onto the scooter. Proceed in the same manner for the other wheel.
B. Wheels: The wheels wear down with time and can be pierced if overused
on rough surfaces. The back wheel on which the brake is applied is
particularly affected after
several hours of braking. In the interest of safety, both wheels should be
checked regularly and changed if necessary.
C. Modifications: The original product must by no means be modified except for the maintenance-related changes mentioned in these instructions.
D. Nuts and axles: These should be checked regularly. They can become
loose after a while in which case they should be tightened. They can become
worn and not tightened
properly, in which case they should be replaced.
MADE IN CHINA
FOR AU / NZ: IMPORTED FOR KMART
STORES IN AUSTRALIA AND NEW ZEALAND.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>