eKids B18 Series True Wireless Earbuds Instruction Manual
- May 15, 2024
- eKids
Table of Contents
B18 Series
True Wireless Earbuds
CHARGE BEFORE USE
B18 Series True Wireless Earbuds
POWER ON/OFF
- Press and hold the Multi-Function Button (MFB) on both earbuds for 3 seconds to turn ON.
- Press and hold either Multi-Function Button for 5 seconds to turn the earbuds OFF.
BLUETOOTH PAIRING
- When the earbuds are ON, they will automatically enter pairing mode. (Note: The LED on one earbud will flash quickly, the LED on the other earbud will blink slowly to indicate earbuds are linked and ready to pair.) For troubleshooting, please visit www.ekids.com/b18
- Select ‘ekids B18’ on your Bluetooth-enabled device to connect. A voice prompt will sound to indicate pairing is complete. Earbuds will automatically connect to your Bluetooth device whenever it is in range.
- To manually pair, press the MFB on both earbuds 2 times while in pairing mode. To pair with a different device, turn Bluetooth OFF on the previously paired device, then turn the B18 earbuds OFF and back ON again to enter pairing mode. To reset Bluetooth, press the MFB on both earbuds 3 times while in pairing mode.
Speakerphone
Answer Call| Double press MFB
Reject Call| Press MFB for 2 sec
End Call| Double press MFB
Voice Assistant
ON/OFF| Press MFB 3x
Bluetooth Audio
Play/Pause| Short press MFB
Volume Up| Press RIGHT MFB for 2 sec
Volume Down| Press LEFT MFB for 2 sec
Next Track| Quick double press RIGHT MFB
Previous Track| Quick double press LEFT MFB
LED INDICATORS
Earbud Charging
Charging| Flashing White LED
Fully charged| LED OFF
Case Charging
Charging| Flashing White LED
Fully charged| White LED solid
To prevent possible hearing damage, do not listen at high volume levels for long periods.
WARNING:
- Earbuds and case may present a choking hazard or cause other injury to small children.
- Keep away from small children
- For your safety, do not use earbuds if they would prevent you from hearing warning sounds, such as while riding a bike, crossing the street, etc.
FCC ID: EMOB18A (Left earbud)
FCC ID: EMOB18B (Right earbud)
FCC Information
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to
the following two conditions:
- This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B) / NMB-3(B)
ISED statements
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This device comply with ISED RF exposure requirement, users can obtain
Canadian information on RF exposure and compliance.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
ONE YEAR LIMITED WARRANTY
For product support and warranty please visit:
www.ekids.com/support
THIS IS NOT A TOY.
Distributed by eKids, LLC
For questions or comments please visit our website:
www.ekids.com
Printed in China
B18_011524-B
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>