TEHILA 24859 Standard Wall Mounted Black Utility Sink Installation Guide

TEHILA 24859 Standard Wall-Mounted Black Utility Sink

MATERIALS AND TOOLS NEEDED

Phillips Screwdriver, Flathead Screwdriver, Silicone, Carpenters Level, Pliers, Pipe Wrench, Plumbers Putty, Hacksaw, Utility Knife.|

WHAT’S INCLUDED IN THE BOX

Tub:

1. Thermoplastic Sink
   Wall-Mounted Tub Kit:

2. Left & Right Fillers

3. Mounting Bracket

4. Lag Screw

5. Wall Anchor

6. Nail Rivet

7. Washer
   Drainage Kit:

8. Rubber Drain Plug

9. rainage Kit

10. Supply line x2

DIAGRAM OF STUD LOCATIONS

STEP-BY-STEP INSTALLATION INSTRUCTIONS

STEP 1
How to punch out faucet holes:

Place the laundry tub on a clean surface, such as a blanket or cardboard, and turn the tub upside down to allow for the removal of the pre-formed knockouts. These will accommodate the faucet that is going to be installed.  The hole plugs may be removed by a flathead screwdriver or a small chisel and a hammer.

STEP 2

Place the wall mounting bracket on the wall. Use a level to ensure the bracket is straight Make sure the drill holes are centered over each stud, then mark them. Remove the bracket and pre-drill a 3/16″ diameter hole into each stud.
NOTE : TYPICAL INSTALLATION SHOWN. LAG SCREW LOCATION MAY VARY DEPENDING ON STUD CENTERS. IF ATTACHING TO MASONRY WALL DRILL TWO (2) 3/8″ DIAMETER HOLES.

STEP 3: Attach the wall mounting bracket to the wall using (2) lag screws. The wall mounting bracket must be straight & level.

STEP 4: Assemble the side filler by inserting the tab into the slotted area under the rear ledge. Bend & position the bottom plate over the molded boss. Insert nail rivets, using a hammer to secure them. Repeat the process for the other side.

STEP 5: Place the utility tub onto the wall mounting bracket (see section view).

STEP 6
Mark the location of side filler mounting tab holes:

Use the stud finder to make sure two holes are centered over wall studs before drilling, then mark the location of side filler mounting tab holes with a pen.
Remove the utility tub and drill holes following the procedures outlined in steps 1 and 2.

STEP 7

Installing the laundry faucet (faucet not supplied):
Mount faucet (not supplied) to the tub following manufacturer requirements.

NOTE : DO NOT SKIP this step before proceeding to the next step.
DO NOT CONNECT THE HOT & COLD SUPPLY LINES YET. SEE STEP 11 FOR CONNECTING SUPPLY LINES.

STEP 8

Re-hang utility tub onto wall bracket and secure side fillers to wall with lag screws and washers as shown in the below image.

STEP 9 : Attach drain connection according to local code requirements.

STEP 10

Installing the plastic drainage:

Step-by-step (see Fig. 2):

1. Slide Slip Nut (C) threads up onto the Tail-Piece (B), and insert Flanged Washer (A) in top of Flanged Tail-Piece (B).

2. Tighten the top Tail-Piece(B) to the Sink Strainer with Slip Nut (C).

3. Insert Slip Nut (C) threads down and Washer (D) on the bottom end of the Tail-Piece (B).

4. Insert Slip Nut (C) threads down onto Wall Tube (E), then insert Sli Nut and Washer (not provided) onto the other end of Wall Tube (E).

5. Place the flanged end of Wall Tube (E) into the lower portion of J-Bend (F)  and tighten with Slip Nut (C). If the wall connection is standard 1 ½ in. threaded pipe, install the wall tube directly into pipe and tighten Slip Nut and Washer (not provided).

   • NOTE: If the wall connection is to 1 ½ in. plastic pipe, a Conversion Adapter, purchased separately, will be required for proper installation (see Fig. 3). Swing J-Bend (F) to align with the bottom of the flanged Tail-Piece (B).
     Connect J-Bend (F) to Tail-Piece (B) and tighten it with Slip Nut (C).
     If the tailpiece is too long, a hacksaw or tubing cutter may be used to trim away excess material.

6. NOTE : When installing new plastic drainage, loosely tighten all pieces first to make a proper fit, then make final connections.

STEP 11

Connecting supply lines to stop valves:

1. Install new water supply lines according to the manufacturers’ installation instructions. DO NOT reuse existing supply lines.(see Fig. 4).

2. Turn on the hot and cold water shut-off valves. CHECK FOR ANY LEAKS AT THESE CONNECTIONS BEFORE RUNNING THE FAUCET.
   If leaks are found, tighten slightly until the leak stops.

3. Run the faucet for at least a minute, as this will flush out any sediment that may have been dislodged during installation. While the water is running, check for leaks at the spray hose connection underneath the faucet deck.
   If leaks are found:

   • (A) Tighten slightly until the leak stops;
   • (B) Make sure the faucet is installed correctly.

1-YEAR LIMITED WARRANTY INFORMATION

TEHILA® products are backed by a 1-year limited warranty. TEHILA warrants that its products will be free from defects in material and workmanship for a period of 1 year from the date of purchase. Proof of the purchaser’s receipt is required to receive this warranty. A replacement for any defective part will be supplied free of charge for installation by you. This 1-year warranty covers the original consumer purchaser only and DOES NOT INCLUDE BUSINESS, COMMERCIAL, OR INDUSTRIAL USE OF THIS PRODUCT. This warranty shall not apply to goods that have been subject to accidents, negligence, installation error, product abuse, or misuse. In no event will TEHILA be liable for any consequential, indirect, or special damages, nor shall TEHILA be liable for transportation, labor, or other charges arising out of the removal or reinstallation of its products? Defective parts must be made available for inspection by a TEHILA employee or an authorized representative. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

WARRANTY CLAIM PROCEDURES AND REQUIREMENTS

To obtain TEHILA® warranty service, the customer will need to write to TEHILA explaining the defect and include proof of purchase receipt, your name, phone number, email address, and mailing address. Information can be emailed to support@tehilalaundry.com or mailed to TEHILA® (Warranty Department), 990 E North Ave., Glendale Heights, IL 60148.

ATTENTION

1. PRIOR TO INSTALLATION: Check all parts carefully to ensure no damage occurs in transit and no pieces are missing. DO NOT dispose of any packaging until you are satisfied with this product.
2. SAFETY PRECAUTIONS: Your installation must comply with all local plumbing codes. Have a qualified tradesman install or approve your plumbing installation. Always wear safety goggles and gloves during installation to avoid personal injury.
3. NEED HELP? Please call us at 1 773-265-2371 or contact us via email at support@tehilalaundry.com with any questions. Our normal business hours are Monday to Friday from 8 a.m. to 5 p.m. CST.
   DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE BEFORE CONTACTING US AT 1(773) 265-2371 OR VIA EMAIL AT SUPPORT@TEHILALAUNDRY.COM.

CARE AND MAINTENANCE

FOR LAUNDRY TUB:

1. Only soap or qualified non-abrasive surface cleaners and water should be used for cleaning the thermoplastic sink. Rinse well and dry with a soft cloth to prevent scratches.
2. Clean grease, oil, paint, and ink stains with isopropyl (rubbing) alcohol. Immediately rinse with water after stain removal.
3. Avoid using razor blades or other sharp instruments that may damage or scratch the surface.

FOR FAUCET:

1. Clean the area of the mounting holes before installing the faucet.
2. To maintain the appearance of your faucet, always blot dry any water from the faucet’s surface. Clean with a damp, non-abrasive sponge and wipe with a clean soft cloth. To remove water spots, apply warm water with a damp soft cloth. Always rinse thoroughly after using a cleaning agent.
3. Although the finish is extremely durable, it can be damaged by some cleaners. DO NOT use detergent powder, polishing powder, granular detergent, or a nylon brush to clean.
4.  DO NOT use abrasive detergents. If used, rinse thoroughly and wipe dry with a soft cloth.
5.  DO NOT install in working environments less than 32 degrees F (0 degrees C).
6.  Shut off the water supply valves when the faucet will not be in use for an extended period of time
7. DO NOT install the faucet in a rusty or corrosive environment.
8. DO NOT TIGHTEN the faucet too hard to avoid deformation or fracture.

• TEHILALAUNDRY.COM
• support@tehilalaundry.com
  We reserve the right to make revisions in the design and information without notice

The image is for reference only, styles vary by models
SKU Numbers : 040JS3502, 040JS3502GRY, 040JS3502BLK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>