TEHILA US6502RD 19 Gallon Red Utility Sink Instruction Manual

TEHILA US6502RD 19 Gallon Red Utility Sink

ATTENTION

1. PRIOR TO INSTALLATION: Check all parts carefully to ensure no damage occurred in transit and no pieces are missing. DO NOT dispose of any packaging until you are satisfied with this product.
2. SAFETY PRECAUTIONS: Your installation must comply with all local plumbing codes. Have a qualified tradesman install or approve your plumbing installation. Always wear safety goggles and gloves during installation to avoid personal injury.
3. NEED HELP? Please call us at 1 773-265-2371 or contact us via email at support@tehilalaundry.com with any questions. Our normal business hours are Monday to Friday from 8 a.m. to 5 p.m. CST.
   DO NOT RETURN THE UNIT TO THE PLACE OF PURCHASE BEFORE CONTACTING US AT 1773-265-2371 OR VIA EMAIL AT SUPPORT@TEHILALAUNDRY.COM

CARE AND MAINTENANCE

FOR LAUNDRY TUB:

1. Only soap or qualified non-abrasive surface cleaner and water should be used for cleaning the thermoplastic sink. Rinse well and dry with suit cloth to prevent scratches.
2. Clean grease, oil, paint, and ink stains with isopropyl (rubbing) alcohol. Immediately rinse with water artier stain removal.
3. Avoid using razor blades or other sharp instruments that may damage or scratch the surface.

MATERIALS AND TOOLS NEEDED

Phillips screwdriver, flathead screwdriver, hammer, silicone, level, pliers, pipe wrench, plumbers putiy, hacksaw, block of wood

WHAT’S INCLUDED IN THE BOX

Tub, legs and levelers, nut and washer, drain plug, plastic drainage (if included)

STEP 1: HOW TO PUNCH OUT FAUCET HOLES & INSTALL STEEL LEGS

1. Place the laundry tub on a clean surface, such as a blanket or carboard, and turn the tub upside down to allow for the removal of the pre-formed knockouts. These will accommodate the faucet that is going to be installed. The hole plugs may be removed by a flathead screwdriver and a hammer (see Fig. 1).

2. While the tub is still upside down, insert the 4 steel legs into each corner socket (see Fig. 2).

3. Use a hammer and a block of wood to drive each leg into the tapered socket until it is secure (see Fig. 3).
   CAUTION:
   • DO NOT strike the leg directly with the hammer. Place the block of wood against
   the leg, then strike the wood with the hammer.
   • IMPORTANT: When installed correctly and the leg is secure, there MAY be a slight gap in the corner between the top of each leg and the bottom of the tub (image A.)
   DO NOT attempt to insert and force past this gap to make them flush.
   This WILL crack the tub (image B.)
   • DO NOT wiggle the leg back and forth, as this will loosen it from the tapered socket.
   

4. Mount leveler to each leg. Note that there are two holes in the bottom of the leg at different locations. Select the proper hole that will allow access to the screwhead artier the tub is in the desired location. Attach leveler with ¼ in. (0.63 cm.) bolt and nut and hand tighten it. DO NOT over-tighten it in this step (see Fig. 4).

5. Gently turn the tub back to the correct position artier the steel legs are installed.

6. Position the laundry tub in your desired location. To adjust the level of the tub, move the levelers up or down. Tighten the nuts artier adjusting the levelers to the desired level. Holes on the bottom of levelers are included for mounting the tub to the floor if desired (anchors not furnished).

STEP 2: INSTALLING PLASTIC DRAINAGE (IF INCLUDED)

NOTE: When installing new plastic drainage, loosely tighten all pieces first to make sure of proper fit, then make final connections.

STEP BY STEP (see Fig. 5):

1. Slide Slip Nut❸ threads up onto the Tail-Piece❷, and insert Flanged Washer❶ in top of Flanged Tail-Piece❷.

2. Tighten the top Tail-Piece❷ to the Sink Strainer with Slip Nut❸.

3. Insert Slip Nut❸ threads down and Washer❹ in bottom end of the Tail-Piece❷.

4. Insert Slip Nut❸ threads down onto Wall Tube❺, then insert Slip Nut and Washer (not provided) onto other end of Wall Tube❺.

5. Place flanged end of Wall Tube❺ into lower portion of J-Bend❻ and tighten with Slip Nut❸. If wall connection is standard 1 ½ in. threaded pipe, install wall tube directly into pipe and tighten Slip Nut and Washer (not provided).
   NOTE: If wall connection is to 1 ½ in. plastic pipe, a Conversion Adapter, purchased separately, will be required for proper installation (see Fig. 6).
   

6. Swing J-Bend❸ to align with bottom of flanged Tail-Piece❷. Connect J-Bend❻ to Tail-Piece❷ and tighten it with Slip Nut❸. If tail-piece is too long, a hacksaw or tubing cuter may be used to trim away excess material.

1-YEAR LIMITED WARRANTY INFORMATION

For up to date warranty information, please visit
https://www.utility-sink.com/pages/warranty

Customer Support

INSTRUCTION: 000000

TEHILALAUNDRY.COM | support@tehilalaundry.com
We reserve the right to make revisions in the design and information without notice.
Image is for reference only, styles varies by models.

Documents / Resources

| TEHILA US6502RD 19 Gallon Red Utility Sink [pdf] Instruction Manual
US6502RD, 19 Gallon Red Utility Sink, Red Utility Sink, 19 Gallon Utility Sink, Utility Sink, Sink
---|---

References

• American Express

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>