Kohler 32631-SCLED-TTL LED Bath Bar Installation Guide
- May 15, 2024
- Kohler
Table of Contents
Kohler 32631-SCLED-TTL LED Bath Bar
Specifications
- Product: LED Bath Bar
- Model Number: 1538432-2-A
- Manufacturer: Kohler Co.
- Indoor use only
Product Usage Instructions
Before You Begin
- Turn OFF electricity at the circuit breaker or fuse box.
- Ensure the electrical outlet box is properly grounded.
- Verify a 4″ octagonal 1-1/2″ Min deep electrical outlet box is installed for the LED driver.
- Follow local codes and have the fixture installed by a qualified electrician.
Install the Mounting Plate
Remove screws securing the LED driver and mounting plate, place the LED driver
in the electrical outlet box, align the mounting plate holes with box holes,
and tighten securely with screws.
Connect the Electrical Wires
Connect wires using wire nuts and electrical tape, ensuring proper grounding.
Install the Fixture
Rotate the mounting plate to level the fixture using the leveling screw.
Connect the fixture using the quick connector.
Compliance
The device complies with FCC Rules and Canadian ICES-003 standards. Do not
make unauthorized changes that could void compliance.
FAQ (Frequently Asked Questions)
-
Q: Can this fixture be used outdoors?
A: No, this fixture is for indoor use only as mentioned in the product information. -
Q: Do I need a qualified electrician to install this fixture?
A: It is recommended to have the fixture installed by a qualified electrician to ensure safety and compliance with local codes.
Installation Instructions
LED Bath Bar
Thank You for Choosing KOHLER
Need help? Contact our Customer Care Center.
- USA/Canada: 1-800-4KOHLER (1-800-456-4537)
- Mexico: 001-800-456-4537
- Service parts: kohler.com/serviceparts
- Care and cleaning: kohler.com/clean
- Patents: kohlercompany.com/patents
Warranty
This product is covered under the KOHLER® Indoor Lighting Fixtures Limited Warranty, found at kohler.com/warranty. For a hardcopy of warranty terms, contact the Customer Care Center.
Tools and Materials
Plus
4″ (102 mm) Octagonal 1-1/2″ (38 mm) Min Deep Electrical Outlet Box
Before You Begin
- DANGER: Risk of electric shock. To avoid electrical shock, the electricity must be turned OFF at the circuit breaker or fuse box before beginning installation.
- DANGER: Risk of electric shock. To avoid electrical shock, the electrical outlet box must be properly grounded.
IMPORTANT! Verify that a 4″ (102 mm) octagonal 1-1/2″ (38 mm) Min deep electrical outlet box is installed for the LED driver.
- Follow all local plumbing, building, and electrical codes.
- Please read all instructions before you begin.
- The fixture should be installed by a qualified electrician.
- This fixture is for indoor use only.
- Carefully inspect the fixture for damage.
Install the Mounting Plate
IMPORTANT!
Verify that a 4″ (102 mm) octagonal 1-1/2″ (38 mm) Min deep electrical outlet
box is installed for the LED driver.
- Remove the two screws securing the LED driver and mounting plate to the fixture.
- Unplug the connector to remove the LED driver and mounting plate.
- Place the LED driver inside the electrical outlet box.
- Align the mounting holes on the mounting plate with the holes on the electrical outlet box.
- Securely tighten the mounting plate to the electrical outlet box with the mounting screws.
Connect the Electrical Wires
Make a loop in the ground wire and wrap around the grounding screw on the mounting plate. Tighten the grounding screw.- Attach the ground wire (green), from the quick connector, to the ground wire (usually bare copper or green) from the electrical outlet box.
- Fasten the ground wires together with the provided wire nut.
- Attach the neutral wire (white), from the quick connector, to the neutral wire (usually white) in the electrical outlet box.
- Fasten the neutral wires together with the provided wire nut.
- Attach the hot wire (black), from the quick connector, to the hot wire (usually black) in the electrical outlet box.
- Fasten the hot wires together with the provided wire nut.
- Wrap the wire nuts with electrical tape.
- Verify that all plastic wire nuts are securely fastened and strands of bare wire are not exposed.
Install the Fixture
NOTE: Your product may appear different than the one illustrated. The installation procedure is the same.
- Carefully position the wires inside the electrical outlet box behind the mounting plate.
- Connect the quick connector to the fixture.
- Loosen the leveling screw and rotate the mounting plate with the tabs so that the mounting plate is vertical. Tighten the leveling screw.
- Position the fixture over the mounting plate and align the screw holes.
- Secure the fixture to the mounting plate with the provided screws.
- To level the fixture, remove the fixture and rotate the mounting plate as needed.
Compliance
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
USA/Canada: 1-800-4KOHLER (1-800-456-4537)
Mexico: 001-800-456-4537
kohler.com
References
- How to Use KOHLER Cleaning Products | KOHLER
- Kohler Warranty Info: Product Limited or Warranty | KOHLER
- Kohler Co. Portfolio | Innovation and Design | Patents | Kohler | Kohler
- Toilets, Showers, Sinks, Faucets and More for Bathroom & Kitchen | KOHLER
- Kohler Warranty Info: Product Limited or Warranty | KOHLER
- Kohler Co. Portfolio | Innovation and Design | Patents | Kohler | Kohler
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>