OLIGHT Perun 3 Rechargeable Right Angle Flashlight User Manual
- June 17, 2024
- OLIGHT
Table of Contents
OLIGHT Perun 3 Rechargeable Right Angle Flashlight
IN THE BOX
Table 1:
Flashlight
Above data are tested per ANSI/NEMA FL 1-2009 standard in Olight’s labs for reference
Table 2:
MCC
- Cable length 0.5m
- Input USB-A DC 5V 2A
- Output CC&CV 4.2V 2A
- Time to fully charge About 3.5 hours
INSTRUCTIONS TO USE
Figure 1: Remove the insulating film
Figure 2: Charging
Figure 3: ON/OFF
Figure 4: Lock/Unlock
Figure 5: Moonlight
Figure 6: Turbo
Figure 7: SOS
Figure 8: Change Brightness Level
Figure 9: Timed shutdown
Figure 10-1: The proximity sensor is not activated
Figure 10-2: The proximity sensor is activated when the output window is blocked at close range
Figure 11: Turn off the proximity sensor temporarily
Figure 12: Turn off the proximity sensor permanent.
Figure 13-1: Battery indicator
Figure 13-2: Battery indicator (Moonlight mode)
Figure 14: Lanyard Attachment
Figure 15: How to turn it into a headlamp
HOW TO OPERATE
-
Product specification, see Table 1 and Table 2;
-
Operating instructions as below：
-
Remove the insulating film and lens protective film before use, see Figure 1;
-
Charging, see Figure 2;
-
Turn on/off, see Figure 3;
Single press to turn the light on/off. When the light is turned on, it will return to the previous brightness level selected before the light was turned off (Only the moonlight, low, medium, and high mode can be memorized when the light is switched off. The turbo mode is memorized as high mode, and the high mode will only be memorized for one minute before reverting to medium mode.The SOS mode cannot be memorized). -
Lockout/Unlock, see Figure 4;
When the flashlight is off, press and hold the switch (for about 2 seconds) to access lockout mode (the flashlight will enter Moonlight Mode briefly and then switch off to signal lockout mode activation). To unlock it, please press and hold the switch for over one second until the light flashes once and then moonlight mode is on again. -
Moonlight, see Figure 5;
When the flashlight is off, press and hold the switch for over one second to access the moonlight mode. When the flashlight is turned on again, it returns to the moonlight mode due to its memory function. -
Turbo, see Figure 6;
When the flashlight is on, quickly double press the switch to enter into Turbo, double press again to return. If the memorized mode were High or Medium, the output is Medium; if the memorized mode were Low or Moonlight, the output is the memorized mode. -
SOS, see Figure 7;
Quick press three times or more to enter SOS Mode. (No timer shutdown function) -
Change the brightness level, see Figure 8;
When the flashlight is on, press and hold the switch and it will, starting from the present brightness level, automatically cycle through Moonlight(Turbo/SOS)-Low-Medium-High-Low. The mode is selected when the switch has been released. (Please note: moonlight and turbo are not in the automatic cycle) -
Set timer, see Figure 9;
The flashlight has a long (9 minutes) and short (3 minutes) timer when the light needs to be automatically turned off. When the flashlight is on, double press and hold the switch under the current brightness level to access the timer settings. A single blink accesses the short timer while two blinks accesses the long timer. The flashlight will automatically turn off when the timer is up. After the timer is set, double press and hold the switch to shift the timer settings. After the first timer runs out and you enter the timer setting again, the last setting will be used. -
How proximity sensor works in Turbo mode
-
The proximity sensor is not activated, see Figure 10-1;
-
The proximity sensor is activated when the output window is blocked at close range, see Figure 10-2; When the light is on and set at Turbo mode or higher brightness (not including SOS mode), if the front lens proximity sensor detects an obstruction nearby, the brightness will automatically reduce to 600 lumens to avoid burning an obstruction nearby. The brightness will restore when the obstruction is gone. The light will turn off directly if the blockage continues for more than 1 minute.
-
Turn off the proximity sensor temporarily, see Figure 11; To turn off the proximity sensor temporarily, please quickly double press(or triple press)the switch within 5 seconds after the automatic dimming. Then, the brightness will restore. Turning off the light can re-activate the proximity sensor.
-
Turn off the proximity sensor permanently, see Figure 12; Quickly press the switch 15 times or more to turn on/off the proximity sensor permanently.
-
Battery indicator
-
Normal mode, see Figure 13-1;
-
Moonlight mode, see Figure 13-2;
-
How to use the pin tool, see Figure 14;
Put the pin tool through the light lanyard hole and then hook the lanyard to the hole. -
How to use the headband bracket, see Figure 15;
-
Remove the pocket clip.
-
Put the flashlight into the bracket with the tail first.
-
Adjust the flashlight to the appropriate position.
DANGER
- Do not leave the battery near the fire or a heated source, or throw the battery into the fire.
- Do not disassemble the battery.
- Don not short circuit (+) and (-) terminals with metallic object intentionally.
CAUTION
- Do not look directly at the light source or shine into the eyes, otherwise it may cause temporary blindness or permanent damage to the eyes.
- Non-standard batteries do not take it out for charging.
- Do not charge the light with any other non-specified chargers.
- Do not leave the light in a car where inside of temperature may be over 60°C, or in similar places.
NOTICE
- Do not use a charging port short-circuited by metal or conductive objects.
- Do not put it in the mouth or lick it, as leakage of the charging port can cause discomfort.
- Keep the charging port clean and dry.
- When the light gets hot, please switch it to low brightness mode, or turn off the flashlight temporarily.
- If the product is left unused for a long period of time, or carried and transported, please loosen the flashlight body a half turn to disconnect the power supply.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual, including
but not limited to using the product inconsistent with the recommended lockout
mode.
WARRANTY
- Within 30 days of purchase: Contact the original seller for repair or replacement.
- Within 5 years of purchase : Contact Olight for repair or replacement.
- Battery warranty: Olight offers a one-year warranty for all rechargeable batteries.
- MCC magnetic USB charging cable : One year. For any of the fragile or low-value fittings not covered above, like lanyard and clip, you can contact the post-sale within 30 days of the purchase, if it has any quality drawback or damage under normal use condition. If such drawback or damage occurs after 30 days of the purchase or under abnormal use condition, we will only offer conditional quality assurance as appropriate.
USA Customer Support
cs@olightstore.com
Global Customer Support
contact@olightworld.com
Visit www.olightworld.com to see our
complete product line of portable illumination tools.
Dongguan Olight E-Commerce Technology Co., Ltd.
4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town,
Dongguan City, Guangdong, China.
Made in China.
Documents / Resources
|
OLIGHT Perun 3 Rechargeable Right Angle
Flashlight
[pdf] User Manual
Perun 3, Perun 3 Rechargeable Right Angle Flashlight, Rechargeable Right Angle
Flashlight, Right Angle Flashlight, Angle Flashlight, Flashlight
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>