ATORCH Ac85-265v Electricity Measure Smart Control Programmable Equipment Instruction Manual

Electricity measure Smart control
Programmable equipment
(Instruction Manual)

Ac85-265v Electricity Measure Smart Control Programmable Equipment

This equipment is used for Smart on-off control, safety protection control, Programmable control, Internet of Things data transmission and wireless control, accumulative power, calculation of electricity bill And measuring detailed parameters such as current voltage, current, power, and frequency

Description of Product Connection Application and Each Function Button

and Interface:

Introduction to the operation of function interface switching and measurement interface value setting:
Turn on the power as shown in the figure above, the display will light up, long press the ‘+’ or ‘-‘ button to switch the display interface of each function forward or backward. Long press the le key to enter the setting interface of the system background. Short press the ‘V key on the front-end interface, the set corresponding number flashes, and then short press the 41- keys to adjust the value. While flashing, continue to short-press the ‘M’ key to switch the number of digits and then adjust the following numbers. When the flashing stops, the system will automatically save and display OK long press the ‘M’ key to save immediately; In normal times, short press the “+/-* key to switch between ‘normally open-normally dosed-auto and other switching modes.
Introduction to the operation of the background setting interface
After long pressing the ‘M’ key to enter the background interface, short pressing the ‘M’ key to cycle down to switch the desired setting menu in a color-changing manner. After changing the color of the selected menu, short press the ‘+/-‘ key to adjust the anent value once or long press to continuously adjust the current value. When in the background interface, long press the I’M’ key to quickly exit the background setting interface and quickly return to the foreground function measurement interface.

Infrared remote control code-learning method and remote control function

application:

After long pressing the key to enter the background interface, short press the “Ms key until the color changes and the infrared remote control leaming and storage’ column is displayed Then short press the ‘+’ button, it will display that the ‘+ ” button is waiting for code learning, then use your NEC format (most remote controllers currently use this format) to aim at the remote control receiving window of this product, and press the first button that you think is convenient to operate the ‘+” position, the code can be learned successfully only MCC The first button is stored in the system, and then it will automatically jump to the display of the second “-” button and wait for you to press the second remote control button on the remote control. When the code is successfully learned and stored, it will jump to the third “M” key to learn the code. After 3 keystrokes are completed, 3 green dots will be displayed, indicating that all the codes have been learned. At this time, long press the “M” key to exit the background to the foreground interface, and you can remotely control this product with the keys that have been successfully learned just now(Because many remote controllers do not have the ability to send codes continuously by long press, it is currently not possible to use the remote control buttons to long press the control function interface switching function). In view of the wide variety of remote controls on the market only the universal NEC code, the remote control has been opened for code learning and control. However, due to the needs of product application scenarios, other keys whose codes have not been learned or remote controllers in non-NEC format also have the function of resurrecting the product in the power-off mode and entering the original setting of the main interface, so as to realize the remote resurrection function of more TV air conditioners and other appliances with remote control function after a smart power failure, thereby meeting the actual application of users. Tips for distinguishing whether it is NEC format remote control: aim at the product receiving window and press your remote control a yellow dot is displayed in the bottom bar of the display, it means that it is in NEC format and can be learned; if it is displayed in red, it is the non-NEC format and cannot be learned.

Setting method and application of safety protection function:

Long press the “+” key to go to the security protection page, short press the “M’ key, and the voltage hundred digits of the overvoltage automatic power-off bar will flash, then short press the “+” or “-” keys to adjust the value, short press the “M” key again, the voltage tens will flash and can be adjusted. Continue with this method, flashing the value of the over-current power column and can be adjusted, after the adjustment is completed, long press the “M” key to save or flash to stop the system to automatically saving. The set protection threshold value can be increased by 5-10% according to your application value, so as to ensure the normal use and also have the power-off protection function (the set protection value will also run in the background of other interfaces). When the input voltage or the power value of the current flow exceeds the threshold you set the system will instantly cut off the power and use the horn to prompt and at the same time display an alarm message on the display for you to check. At this time, if the user’s button signal or infrared remote control signal is not received, the product will continue to power off. Until the user releases the danger and presses any key or remote control key on the host the system will return to the protection interface and automatically be in the off state, waiting for the user to reset or restart the power.

Security protection settings skills for charging, such as applying smart

power off (Category A) to electric vehicles or full power failure of mobile phones:

Long press the “+” button to go to the smart power-off category A page and select the “on’ state, observe and record the charging power value of the charged device once after it is fully charged; Then, add 2-5W on the basis of this value, which is the power value of how many watts of your full automatic power-off setting is less than the continuous value and turn on the “auto” gear. In this way, when the system detects that the current power value is less than the power value you set and continues for the recharge time you set the system displays the power-off icon and cuts off the power output thereby protecting your device(The longer the duration you set the longer the subsequent charging time is when it is fully charged, so as to ensure that the device can be fully charged and at the same time double-monitoring to achieve accurate and automatic power-off for safe charging protection).
Tips for viewing the progress bar and countdown in the lower right corner of the display interface:
When the system detects that the measured power value is less than the power value you set the system starts counting down, and the progress bar is calculated according to the duration ratio you set. The progress bar decreases and changes color from yellow to red until the end of the power failure. When the power value measured by the system is greater than the power value you set at a certain moment the countdown will be cleared immediately, the progress bar will fill up instantly, and then a new round of detection will be performed.

Power saving setting skills, such as applying smart power off (Category

A) to TV air conditioners with infrared remote control, etc.:

Long press the “+” button to go to the smart power-off category A page and select the “on” state, observe and record the standby leakage power value of the connected TV, air conditioner, and other equipment after the remote control is turned off. Then, add 2-5W to this value. This is how much watts of power your device should be set to and turn it on to the “auto” gear. In this way, when the system detects that the current power value is less than the power value you set it will judge that you have used the remote control to turn off the electrical equipment and enter the standby state. At this time, the system starts to count down to the duration value you set, and the system judges that you will not use the device anymore and automatically disconnects the power supply to save power waste and safety protection when the device is on standby power. When the power is automatically disconnected, the system home prompts several times, and at the same time, it displays a red power-off information interface. At this time, if the system detects any key signal or your device’s remote control signal and mobile phone APP and other key signals, it can resurrect and return to the smart power-off interface, and automatically turn on the power again and start the next round of the smart power-off process.

Setting skills, such as applying smart power off (Class B) to avoid loss of electricity bills caused by people leaving home for a long time and forgetting to tum off the device :

Long press the “+” button to go to the smart power-off type B page and select the ‘on’ state. Observe and record the minimum power value of the connected device when it is powered on. Then, subtract 5-25W on the basis of this value. This is how many watts of power should be set for your connection and turn it on to the ‘auto’ gear. In this way, when the system detects that the current power value is greater than the power value you set, it will judge that your device has been powered on. At this time, the system starts to count down to the duration value you set and the system determines that you may have forgotten to turn off the device because you left home and automatically cut off the power, so as to achieve the purpose of people accidentally forgetting to turn off the equipment and causing the equipment to own for a long time when no one is left which consumes huge electric energy and causes huge loss risks. When the power is automatically disconnected, the system horn will beep several times, and at the same time, a red power-off information interface will be displayed. At this time, if the system detects any key signal or your device’s remote control signal and mobile phone APP and other key signals, it can resurrect and return to the smart power-off interface, and automatically turn on the power again and start the next round of the smart power-off process. This feature comes from a real story: A worker who travels frequently, carelessly forgot to turn off the air conditioner at home before a business trip. The air conditioner was turned on for a few months during the business trip. After returning home, he found that he had used thousands of kilowatt-hours of electricity and caused a loss of thousands of yuan.

Setting methods, such as applying the dining per supply page to digging

devices such as mobile phones or electric vehicles.

Long press the “+’ button to go to the timing power supply page, set the time you are expected to be fully charged by the charging device, and then press the “+’ button to enter the automatic mode. The system is powered on and the countdown reaches the time you set. When the system automatically cuts off the power output on time, the speaker emits a beep and the display shows a red cut off the interface.
Applying the cyclic timer switch in intermittent oxygen addition to fish ponds or exhaust fans, electric lights, sheet fights, electrical appliances, etc:
This feature can be used to intermittently add oxygen to fish ponds or household fish tanks, to provide intermittent power supply to electric fans to achieve a natural wind-like atmosphere and to provide intermittent power supply to some exhaust fans to save electricity bills, and to program time for other devices that require an intermittent power supply and then be automatically controlled by their time axis. The opening or closing time can be set to any time you need according to different situations. On some occasions that do not need to use electricity for a long time, you can use this product to change it to any time, with intermittent power supply, thereby saving power and reducing costs.

Difference between several programming liming switches:

Timing power supply page : The power supply will be disconnected after the countdown operation ends according to the time set by the user;
Cycle timing switch : according to the different switch duration set by the user, the countdown is turned the off-on-off automatic cycle power supply
Countdown switch page: According to the different switch duration set by the user, a countdown is turned on and then turned off.

The electrical energy monitoring page of the product homepage is suitable for measuring and statistics of electrical energy and electricity parameters of various electrical appliances:
It can be connected to the main distribution box of your home through the wiring port on the back of the product. It can realize electricity statistics, electricity bill calculation, and current voltage, current, and power values. It can also provide 24-hour full safety protection for automatic power-off when encountering overvoltage or overcurrent power; It can be connected to different rooms of the shared house as a basis for sharing electricity charges. It can also be connected to your home appliances such as refrigerators, washing machines, induction cookers, etc. through the socket output so as to count its power consumption and calculate its electricity consumption and other detailed information.

APP Connect the Bluetooth

Search “E test” in Apple APP or scan the bar code of Android to download and install, click the icon to open the APR then click the Bluetooth icon in the upper left corner of the interface, and select..24-BLE model to return to the main interface of APP automatically. At this time, the Bluetooth icon of your phone will change from gray to blue, and that means communication is successfully connected.
Warning: If the Bluetooth model of 1124-BLE cannot be found in the electricity meter APR please make sure to tum on storage permission and location information options of this APP in your phone Settings! Make sure All are open!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>