Cycleinn CI-FT001 Bike Exercise Trainer Stand with Noise Reduction User Manual

: June 17, 2024
: Cycleinn

Table of Contents

CI-FT001 Bike Exercise Trainer Stand with Noise Reduction
Spare Part List
Installation instructions
Care and Maintenance
FAQ
Product specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OPERATION INSTRUCTION

Cycleinn CI-FT001 Bike Exercise Trainer Stand with Noise
Reduction

Product Name : Bike Trainer
Product Models : Cl-FT001

CI-FT001 Bike Exercise Trainer Stand with Noise Reduction

WARNING

Persons with limited physical, sensory or mental capabilities or those with a lack of experience or knowledge should not use this indoor bike trainer, unless they are supervised or if they have been informed about using it safely and understand the relevant risks of use. Children must not play with the indoor bike trainer or any of its parts. Children may not service or clean the product without adult supervision.
Do not touch the resistance roller during or after training as this can become very hot. Risk of burns Keep children and animals away from the indoor bike trainer at all times.

NOTICE

Please ensure that the indoor bike trainer is positioned securely only train on a firm, even and non-slip surface Adjust the indoor bike trainer as required using the adjustable stand feet.
Should you experience pain, nausea, dizziness, weakness or chest pains, please terminate your training immediately and consult your GP.

Spare Part List

No.	Name	Quantity
A	Main body of bike trainer	1
B	Reducing wheel	1
C	Front wheel fixed seat	1
D	Release lever	1
E	Hexagon socket cap head screw M8*85	1
F	Locking nut M8	1
G	Flat washer φ8	2
H	Open end wrench	1
I	Inner hexagon spanner	1

Installation instructions

Step 1 Assembly of bike trainer

1-1 open the box, check all parts and quantity according to the spare part list.

1-2 Installation

As shown in Figure 2, unfold the supporting foot stand of the bike trainer on the ground. Make the bike trainer stable by rotating the base sleeve on the base tube, so that the four pedestal sleeves can fully contact the ground at the same time, and the riding platform does not shake.
As shown in Figure 3, move the adjusting foundation to the bottom by hand.
As shown in Figure 4 and 5, install the reducing wheel on the frame and penetrate the adjusting knob into the pin hole.
As shown in Figure 6, turn the adjusting knob anticlockwise to the proper position and pull the quick tightening wrench up.

Step 2 Bike installation

First check whether the tire pressure of the bike is at normal state.
Install the bike on the bike trainer, adjust the T-handle of the left knob to make the bike tire roughly in the middie of the roller. After fixing the bike, push the handle lock ring to the innermost side, as shown in Figure 7.
Adjust the adjusting knob clockwise to make the roller tightly touch the tire, and then tighten the adjusting knob for one and a half to two turns to make the roller fully fit the tire.
Note: Make sure to level the bike trainer before use, $0 as lo avord accidental injury caused by the shaking of the bike trainer

Step 3 Placing front wheel riser block
As shown in Figure 8, fix the standard front wheel fixed seat right below the front wheel of the bike.

Step 4 Trail operation

Confirm again that the bike is firmly installed and fixed, and the frame is fully fitted with the ground without tilt.
While riding, first step on the crank at a slow speed. If there is no first step on the crank at a slow speed, and then increase the speed without any abnormality, you can then increase the speed.

Care and Maintenance

Care
1-1 The product can be folded for storage. Operation method: Close the supporting stand foot in. Pay attention to avoid hurting hands when folding them.
1-2 The product shall be stored in a clean and dry indoor environment, avoiding direct sunlight, away from fire and water sources or other dangerous goods.
1-3 Just wipe the product with a clean cloth for cleaning. Do not use detergent, cleaning powder or other chemical solvents to clean it, so as not to damage the surface paint of the bike trainer.

FAQ

When an exception occurs, please check and resolve it according to the table below. Bike shaking

• The ground is rough, or the user fail ta level the bike trainer according to the instructions. Please level the bike trainer according to step 1. * The handle is not locked in place and the bike is not firmly fixed.

Bike tires are seriously worn

• Check whether the tire pressure is low and inflate to make up the tire pressure. • Check whether the roljler and the bike are too closely or loosely contacted, adjust according to step 2-3.

Noise

The noise is mainly related to the materials and tread of bike tires. The use of road bikes is highly suggested because the spinning sound will be louder and it possible to wear out the tires if mountain bike is used. We also recom- mend using the bike trainer on a carpet to reduce noise.