ATOMSTACK F03-0192-0AA1 Laser Module Instruction Manual

ATOMSTACK F03-0192-0AA1 Laser Module

Specifications:

• Product Name: AtomStack M150 Laser Module
• Model Number: F03-0192-0AA1
• Version : A
• Class : Class 4 laser product
• Compliance : IEC 60825-1 latest version

Product Usage Instructions

Security Statement and Warning:

1. Installation Requirements:
   • This laser module is a component of a laser engraver system and should be installed in a laser engraver that meets IEC 60825-1 requirements.
   • The laser engraver must have a protective housing to prevent human access to laser radiation.
2. Protective Measures:
   • The laser itself should have a protective cover securely fastened with screws.
   • The laser engraver housing should include an interlock function to automatically turn off the laser when opened.
   • An emergency stop button should be present to halt laser output in unexpected situations.
3. Operational Safety:
   • Use physical keys, dongles, or password systems to control access and prevent unauthorized operation.
   • Set up warning marks on any window or channel that can observe or receive laser radiation.
4. Emergency Procedures:
   • In case of skin or eye contact with the laser, seek immediate medical attention.

Disclaimer and Warning:
This product is not intended for individuals under 15 years of age. Keep the laser module out of reach of children and operate with caution in the presence of children.

Security Statment and warning

Before Using the laser engraving, please read this safety guide carefully, it mentions situations that require special attention and includes warnings of unsafe practices that can cause damage to your property or even endanger your personal safety.

1. This product is a laser engraver system component, that must be installed in other manufacturers of laser engravers for use. If the product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, otherwise, the product is prohibited to be used.
2. Your laser engraver shall have a protective housing which, when in place, prevents human access to laser radiation. 3. If a protective housing is equipped with an access panel that provides “walk-in” access then:
3. means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to Class 3B or Class 4.
4. warning device shall be situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the protective housing.
5. where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to
6. Class 3B or Class 4 while someone is present inside the protective housing of a Class 1, Class 2, or Class 3R product shall be prevented by engineering means. NOTE Methods to prevent human access to radiation when persons are inside the protective housing can include pressure-sensitive floor mats, infrared detectors, etc.
7. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the protective cover should be checked to be reliably locked, and can not be removed in the energized state.
8. The housing of the laser engraver should have an interlock function. When the housing is opened or removed, the laser can be automatically turned off.
9. The laser engraver should have an emergency stop button, which can immediately stop the output of the laser when pressed under unexpected circumstances.
10. The laser engraver should have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or emergency stop.
11. Laser engravers should use physical keys, dongle, password system and other ways to manage and control, to prevent personnel without security training operating of this kind of equipment.
12. On the laser engraver any window or channel that can actively observe or passively receive the laser radiation should be set up with warning marks.
13. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.

Disclaimer and warning

• This product is not a toy and is not suitable for people under 15 years of age. Do not allow children to touch the laser Module. Please be careful when operating in scenes with children.
• This product is a laser module, visit http://www.atomstack.com/laserengraverdownload for a complete “user manual” and the latest instructions and warnings. Shenzhen AtomStack Technologies Co., Ltd. (Atomstack) reserves the right to update this Disclaimer and Safe Operation Guidelines.
• Please be sure to read this document carefully before using the product to understand your legal rights, responsibilities and safety instructions; Otherwise, it may bring property loss, safety accidents and hidden danger of personal safety. Once you use this product, you shall be deemed to have understood, accepted and accepted all terms and contents of this document. The user undertakes to be responsible for his or her actions and all consequences arising there from. User agrees to use the Product only for legitimate purposes and agrees to the entire terms and contents of this document and any relevant policies or guidelines that AtomStack may establish. You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and provide you with AtomStack’s after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used, operating system information, video of the engraving or cutting process, and operational steps prior to the occurrence of a problem or failure.
• AtomStack is not liable for any and all losses arising from the user’s failure to use the product in accordance with this manual. Atomstack has the ultimate right to interpret the document, subject to legal compliance. Atomstack reserves the right to update, modify, or terminate the Terms without prior notice.

Accessories list

Installation method

• If the machine is as shown in the figure below, please install the dovetail slider
• Remove the original laser and laser fixed slider The fixed slider of M150 module is a dovetail slider. If the original machine slider is also a dovetail slider, the M150 module can be directly installed and used;

If the machine is as shown in the figure below, there is no need to install the dovetail slider

For users who want to use the previous laser module after replacing the cable, we have provided a conversion cable, please choose according to your needs

Wiring method

Note : The driving current of M150 module is relatively large, you need to use the equipped motherboard cable

• A lot of smoke is generated in engraving or cutting wood and other objects.be aware of cleaning the air guide hood and anti-skid cover, since there may be a lot of dust accumulation on itespecially working with more than 50% of the laser power.
• Remove the shield if you could tum on the air assist while the machine is working, all of which would significantly reduce dust accumulation.

The laser dower of this machine is very heavy. if you need to cut wood and other flammable materials with a power of more than 70%, please ensure someone is watching the machine in case of the flammable materials catches fire.

Cautions: LASER BEAM CAN DAMAGE EYES

1. Laser Light can damage the human eyes and skin. Do not expose the eye or skin to laser light directly.
2. This Laser product has an optical lens and emits a collimated laser beam.
3. The light from this product, both direct and reflected, is very harmful as it can propagate a long distance while maintaining high optical density.
4. When handling the product, wear appropriate safety glasses (OD5+) to protect eyes from laser light including reflected and stray light.
5. The reflected and stray light spilling into an unintended area should be attenuated and/or absorbed.

Maintenance instructions and warning

This product uses a highly integrated design and requires no maintenance. However, if the laser system installed with this product needs to be repaired or tuned, please:

1. Unplug the power cord on the laser, so that the laser is in a state of power failure;
2. If you need laser assistance for tuning, please:
3. All present personnel wear protective glasses, OD5+ protective glass is needed ;
4. Make sure there are no flammable or explosive materials around;
5. The position and direction of the laser are fixed to ensure that the laser will not accidentally move and shine on people, animals, flammable, explosive and other dangerous and valuable objects during debugging.
6. Don’t look at lasers
7. Do not shine the laser on the mirror object, lest the laser reflection cause accidental injury.

Customer Service:
For a detailed warranty policy, please visit our official website at: www.atomstack.net

For technical support and service, please
email : support@atomstack.net

Manufacturer : Shenzhen AtomStack Technologies Co., Ltd. Address: 202, Building 1, Mingliang Technology Park, No. 88 Zhuguang North Road, Taoyuan Street, Nanshan District, Shenzhen, Guangdong, China

Scan the code to enter the discussion group.

Scanner APPLICATION:
QR code reader/ Barcode scanner or any APP with the scanner.

FAQ

Q: How do I ensure the protective cover is securely fastened?
A: When installing the laser on the engraver, make sure to check that the protective cover is reliably locked in place and cannot be removed while energized.

Q: What should I do in case of accidental exposure to the laser?
A: If the laser burns the skin or eyes, immediately seek medical attention at a nearby hospital for examination and treatment.

References

• Atomstack Official Store - Laser Engraving Machine

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>