Farmice BF11 Smart AI Recognition Bird Feeder User Manual

Farmice BF11 Smart AI Recognition Bird Feeder

USER MANUAL

NOTES

1. Keep the bird feeder and all accessories out of reach of children and pets.
2. Make sure the camera has been fully charged .(DC 5V/2A)
3. Working temperature : -5°F to 120°F(-20.5°C to 48.5°C) Working relative humidity: 10%~95%
4. Please do not expose the camera lens to sunlight directly .
5. The camera has an IP65 waterproof rating, which support working properly under rains or snows. But it can not be soaked in water.
6. The bird feeder can only works with 2.4GHz WI-FI.
7. The strong light will interfere the scanning of the QR code while pairing
8. Avoid placing the device behind furniture or near microwaves products.
9. Try to keep the bird feeder within the range of your WI-FI signal.

WHAT’S IN THE BOX

INTRODUCTION FOR BIRD FEEDER

SPECIFICATIONS FOR BIRD FEEDER

SOLAR PANEL SPECIFICATION
IPCE| 19%
Working Voltage (Vmp)| 6V±5%
Working Current (Imp)| 400mA±5%
Open Circuit Voltage (VOC)| 7.2V±5%
Short-Circuit Current (ISC)| 480mA±5%

INTRODUCTION FOR CAMERA

CAMERA SPECIFICATION

INDICATOR STATUS

1. Camera turn on: Red light always ON.
2. Pairing mode: Red light fast blinking.
3. Network connecting: Green light fast blinking.
4. Network connected: Green light always ON.
5. Abnormal status : Red light slow blinking.(Need to reset)
6. During firmware update: Yellow light always ON.
7. Charging status: White light always ON during charging and OFF after fully charged.

HOW TO CONNECT TO THE APP

Download or scan the QR code and install the Bird Lover App for either IOS or Android. Once downloaded, the APP will prompt you to register your device. Enter your phone number or email address which one makes you feel comfortable and select the country you live in. You will receive the registration code. Input the registration code, then create a password.

WIFI MODE CONFIGURATION (COMMON)

1. Entering the “Add Device” interface, click the “Add Device” or “+” on top right corner to add new device. (refer to picture ①)
2. 2.Selecting any “Smart Bird Feeder” icons below to add the device.
Turn on the device and make sure the red light is flashing quickly, and then please follow the instruction steps in the APP to add the device.
(refer to picture ②)

Or refer to the following stepts:

APP INTERFACE INTRODUCTION

1. Quality adjustment : you can choose HD or SD
2. Battery Remaining Capacity
3..Voice switch
4.Zoom in the screen for camera
5. Screen horizontal and vertical adjustment
6. Take photo
7. Bird recognition 8.Shot videos
9. Playback for previous
10. View photos or videos took
11. Check out the bird collection

12. Share the device
13. Motion detection(Click to turn on/off)
14. Device Volume 15.One-Way Talk
16. Siren 17.Notification for motion detection
18. Cloud storage service
19. History for bird recognition
20. Personal setting

TOP COVER INSTALLATION

1. Align the top cover with the groove of the birdhouse and press down.

2. Connect the battery charging cable to the top cover

3.Twist and snap the top cover.

HOW TO INSTALL

The first installation method.

1. Using the provided drill sticker inside the box to mark the position of holes in the wall. Using drill bit to drill 4 holes.

2. Installing 4 Anchors.

3. Installing the screws to fix the bracket

4. As shown in the picture, put the Bracket connector into the bottom of the bracket, use 3pcs long screws to install with the bird feeder, then the bird feeder is fixed.

5. After opening the lid and adding the bird food, as shown in the picture, fastening the 2pcs Short screws can prevent it from being opened by squirrels.

How to INSTALL

The second installation method.

1. Unscrewing 4 pcs of screws from the Bird feeder wall mount and put them aside.

2. Putting plastic accessories on the back, re-tighten the 4pcs screws.

3. Using the provided drill sticker to mark the position of holes in the wall.
Using drill bit to drill 4 holes.

4. Installing 4 Anchors

5. Installing the screws to fix the bracket.

6. As shown in the picture, put the Bracket connector into the bottom of the bracket, use 3pcs long screws to install with the bird feeder, then the bird feeder is fixed.

7. After opening the lid and adding the bird food, as shown in the picture, fastening the 2pcs short screws can prevent it from being opened by squirrels.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>