Soldcold FF01 Dog Training Collar User Guide
- June 17, 2024
- Soldcold
Table of Contents
Soldcold FF01 Dog Training Collar
Soldcold РЕТ QUICK START GUIDE
Dog Training Collar Model: FF01
Please read the quick start before use
support@soldcolds.com
WE MAKE IT EASY 24/7
Important Safety Information
WARNING
- Your dog must be at least 6 months old to use this training collar
- Not leaving the collar on your dog over 12h per day. (Better within 6h.)
- Reposition the collar on your dog’s neck every 1-2h
- Not install the metal contact points when shock function is not be used
- Check the skin condition of dog’s neck every day, for any abnormalities please suspend the use of this product and consult doctor
Specifications
- Product name : Dog training collar
- Product model: FF01 FCC ID: 2BAWZ-FF01
- Material: ABS Battery capacity: remote control 300 mAh; receiver 300mAh
- Chargingvoltage:5V/250mAh
- Charging time: 1.2 hours
- Charging port: Type-c USB Operate range: 1600FT
- Remote control frequency: 433M FSK
- Operating temperature: 32-104, <95%RH Remote
- Waterproof Rating: Non-Waterproof Receiver
- Waterproof Rating: IPX7
- Standby time: 20 days for remote control; 10 days for receiver.
- Receiver sensitiv ity:-126DBm
- Endurance: 6H continuously working
- Working temperature : -30 C – 70 C Storage temperature: -30 C – 85C
- Scope of application: all kinds of dogs
Overview (Remote)
- Channel Conversion
- SwitchLock Keyboard
- Level Display
- Beep Button
- Vibration Button
- Shock Button
- LED Indicator
- Battery Display
- Setting Mode
- Shock /Vibration Level + –
Overview (Receiver collar)
Pairing Operation
Tips: In the 1-pair package, the receiver and controller area already paired on dog channel 1 by default.
- Operate the remote: press CH button to select the channel you need.
- Operate the receiver : Briefly press the power button twice, till the light turned blue and start flashing.
- Operate the remote : Press vibrate or beep or shock button to finish the pairing.
- When the blue light turned off means the pairing has done.
- Change the channel: I f you want to change the receivers channel please repeat the above procedure
Function Test
Beep Test
A press on the Beep button will deliver a beep with non-adjustable volume to
the receiver.
Vibration Test
A press on the Vibration button will deliver a vibration with non-adjustable
intensity to the receiver. 8-level setting
Shock Test
Put the test lamp vertically on the contact points and make sure the metal
wire in the test lamp has direct contact with the top of the points. Press the
Shock button to send a shock to the receiver, the test light will be light.
The light changes its brightness accordingly with the Shock Level adjusted
from 0-18 level.
How to setting level
Vibration Level :
- Press M button first,
- The vibration icon flashes,
- Press the plus and minus buttons
Shock Level:
- Press M button
- The shock icon flashes,
- Press the plus and minus buttons
Certification Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The company declares under its own responsibility that this product complies with the basic requirements of CE (2014/ 30/EU) and RoHS (2011/65/EU). Without the approval of our company or the distributor, unauthorized changes or modifications to the equipment may violate the CE regulations, may cause the user to lose the right to operate the equipment, and invalidate the warranty.
Recycling Information &Battery
Disposal Please observe the regulations for electronic and electrical devices
to be disposed of in the respective country. In some countries or regions this
device must be recycled. If this device is no longer required, it must not be
disposed of with normal municipal waste. Separate collection of spent
batteries is required in many regions; check the regulations in your area
before discarding spent batteries. For more recycling information, please
refer to local regulations.
Warranty
12-month limited warranty
Any Problem Please Email US
Customer Support:
- Support@soldcolds.com
- https://soldcolds.com
- WhatsApp: +1(659)253-6051
Made in China
Documents / Resources
|
Soldcold FF01 Dog Training
Collar
[pdf] User Guide
FF01 Dog Training Collar, FF01, Dog Training Collar, Training Collar, Collar
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>