O2Ring Wearable Oxygen Monitor User Manual

O2Ring Wearable Oxygen Monitor

Introduction

Intended use
This product is intended to be used for measuring, displaying and storing of pulse oxygen saturation (SpO2), pulse rate of adults in home or healthcare facilities environment for sleep or daily use.
Notice: It’s not a medical device. This device is for Sports and Aviation use only and not intended for medical use.

Warnings and Cautions

• DO NOT squeeze the sensor part or apply excessive force on it.
• Do not use this device during MRI examination.
• Do not use this device with a defibrillator.
• Do not store the device in the following locations: locations in which the device is exposed to direct sunlight, high temperatures or levels of moisture, or heavy contamination; locations near to sources of water or fire; or locations that are subject to strong electromagnetic influences.
• Do not use the device in a combustible environment.
• Never submerge the device in water or other liquids.
• Do not clean the device with acetone or other volatile solutions.
• Do not drop this device or subject it to strong impact.
• The device and accessories are provided non-sterile.
• Do not place this device in pressure vessels or gas sterilization device.
• Do not dismantle the device, as this could cause damage or malfunctions or impede the operation of the device.
• Consult your doctor immediately if you experience symptoms that could indicate acute disease.
• Do not self-diagnose or self-medicate on the basis of this device without consulting your doctor. In particular, do not start taking any new medication or change the type and/or dosage of any existing medication without prior approval.
• Use only cables, sensors and other accessories specified in this manual.
• Prolonged continuous monitoring may increase the risk of undesirable changes in skin characteristics, such as irritation, reddening, blistering or burns.
• Do not open the device cover without authorization. The cover should only be opened by a qualified service personnel.

Guide to Symbols

Unpacking

• Device
• User Manual
• Data/Charging Cable

Overview

Using the Device

Charging
Charge the battery before using. Connect the device to computer USB or USB charging adapter with USB cable.

After fully charged, the device will power off automatically.

POWER ON/OFF

• POWER ON:
  Wear the device, it will turn on automatically.

• POWER OFF:
  The device turns off automatically in a moment after you take it off.

Typical steps

1. START. Charge the battery. Wear the device to power on.
2. STOP. Take off the device, the recording will be over after the countdown.
3. DATA SYNC. After the countdown, run App to sync data. OR next time after you turn on the device, run App to sync.

Start working

1. Wear the device on thumb finger, index finger as option in case of too tight for thumb. Try to move the device along the forefinger to find out a best fit. Avoid being loose. Loose wearing causes inaccurate measure.
2. Device will turn on automatically. After a few seconds, the device will begin to monitor.

Notice:

• Keep snug enough, loose wearing may cause inaccurate readings.
• DO NOT use middle finger; if too tight for thumb or forefinger, try little finger.
• If the working time is less than 2 minute, the data will not be saved.
• Please avoid excessive motion.
• Please avoid strong ambient light condition.

Stop working & sync data
Take off the device, the countdown will begin. (If the working time is less than 2 minute, there will be no countdown)
During the countdown, if you wear the device again, the record will be resumed. After the countdown, the data will have been saved in device and ready to sync.

Sync data:

• After the countdown, run App to sync data;
• OR next time after you turn on the device, run App to sync.
  Notice: The built-in memory can store 4 sessions. The oldest will be overwritten by the 5th. Please sync data to your phone in time.

Screen Wake up
The screen will go off automatically for saving power in Standard Mode; you can touch the key on top to wake up the screen.

How to Check Battery
Touch the key on top, you can switch display between readings and battery.

Unavailable Symbol
When this symbol displays on device screen, it indicates the readings is unavailable right now. It may caused by:

• Excessive movement;
• Poor signal, finger is too cold;

Usually, the readings will recover in a few seconds when at rest.

Download App

• App name: ViHealth
• iOS: App Store
• Android: Google Play

Compatibility
The device is compatible with iOS versions 9.0+ and Android versions 5.0+. Please Refer to the ViHealth app manual for more details.

Bluetooth Connection
The device Bluetooth will be enabled automatically after it’s turned on. To establish a Bluetooth connection,

1. Keep the device Bluetooth enabled.
2. Make sure the phone’s Bluetooth is enabled.
3. Run the App.

Notice: DO NOT PAIR in the settings of your smart device.

PC software

PC Software: O2 Insight Pro
Download from: www.getwellue.com
Enter top menu: Support->PC Software. Install the software on Windows (Win 7/8/10) or MacOS(10.13 or above).

Install the software on the PC:

1. Turn on the device, connect the device to PC USB port with the supplied Data Cable (it’s different from a universal USB cable)
2. Run the PC software, and click the Download button to download data from the device. With the PC software, you can view and print sleep reports, which can also be exported as PDF or CSV files.
   Note: while the device is being connected to app, it can’t connect to PC software.

Maintenance

Time & Date
After connection with the App, device time will sync from your phone time automatically.

Cleaning
Use a soft cloth moistened with water or alcohol to clean the device’s surface.

Troubleshooting

For more information about O2RIng, please visit: https://getwellue.com/pages/faqs

Specifications

Manufacturer: Shenzhen Viatom Technology Co., Ltd
Address: 4E,Building 3, Tingwei Industrial Park No. 6 Liufang
Road, Block 67 Xin’an Street, Baoan District Shenzhen 518101 Guangdong China
Contact us: support@getwellue.com
Website: www.getwellue.com
Model: PO2
Version: A

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>