Aoshet ‎‎B0CKX74BMZ Astronaut Lights User Manual

Aoshet ‎‎B0CKX74BMZ Astronaut Lights

User’s Manual

Attention

• The light sources of stars and nebulae are so intense that the eyes cannot look directly at the light sources.
• The brightness of stars (i.e. laser brightness) is affected by ambient temperature and time. When the ambient temperature is high, or the power-on time is long, the laser brightness will decrease down to heat. In this case, just turn off the transmitter to let it cool down (usually it takes more than 15 minutes) and then turn it on to restore the brightness.
• The astronaut’s head and body are connected by magnets, and the direction of the head can be adjusted. Do not stretch the head and body forcefully, otherwise the circuit may be broken.

The projection direction can be adjusted by adjusting the rotation of the astronaut’s head.

FAQ

• What should I do if the laser brightness decreases?
• If the laser brightness decreases due to high ambient temperature or prolonged use, turn off the transmitter to let it cool down for at least 15 minutes before turning it back on.
• How do I adjust the projection direction?
• The projection direction can be adjusted by rotating the astronaut’s head.
• Can I stretch the astronaut’s head and body?
• No, the head and body are connected by magnets and should not be stretched forcefully to avoid damaging the circuit.
• How do I operate the remote control?
• Refer to the ‘Remote Control Operation Instructions’ section for detailed information on using the remote control.
• What are the optimal conditions for using the projector?
• The optimal use environment is indoors, in a dark setting, with an operating temperature range of -10 to +45℃.

Please note: The image descriptions provided for the astronaut figure and the host key diagram are based on the content shown in the image and are included to make the document accessible to visually impaired users.

Introductions

• The light sources of stars and nebulae are so intense that the eyes cannot look directly at the light sources.
• The brightness of stars (i.e. laser brightness) is affected by ambient temperature and time.
• When the ambient temperature is high, or the power-on time is long, the laser brightness will decrease due to heat.
• In this case, just turn off the transmitter to let it cool down (usually it takes more than 15 minutes) and then turn it on to restore the brightness.
• The astronaut’s head and body are connected by magnets, and the direction of the head can be adjusted.
• Donat stretch the head and body forcefully, otherwise the circuit may be broken.

Host key operation instructions

• Nebula Color Switch: short press to switch nebula color, each press to switch a color, and so on. Long press to close.
• Moon switch: short press to close, short press again to open.
• Star switch: short press to turn off, short press again to turn on.
• Power switch: short press to turn on, after turning on the nebula/stars and moon by default.
• Power Jack

Remote control operation instructions

• Main switch: short press to turn on, the nebula/stars and moon are turned on by default, and short press again to turn off.
• Star switch: short press to turn off, short press again to turn on again.
• Nebula switch: short press to turn off, short press again to turn on again.
• Nebula color changing mode: short press to enter this mode.
• Nebula red ambient light
• Nebula green ambient light
• Nebula blue ambient light
• Nebula color switch: short press to switch the color of the nebula, each press to switch color, and so on.
• Cancel timing settings: Short press, the moon flashes 3 times, the time setting will be canceled.
• 1-hour timing settings: Short press, the moon flashes once, and it will automatically shut down after 1 hour.
• 2-hour timing settings: Short press, the moon flashes once, and it will automatically shut down after 2 hours.
• Nebula change speed t: The speed is divided into four gears: 0-1-2-3.
• Gear 0 is static, gear 3 is the fastest, and the default is gear 2. Each time you press the speed, it will increase by one gear until gear 0.
• Nebula brightness ‡: A total of 3 levels, the default brightness is the middle level, and the brightness increases by one level each time you press.
• Moon color switch: Short press to switch colors, each press to switch color, and so on, long press to close.

SPECIFICATIONS

• Material: ABS/PC/PVC
• Color: White
• Laser Wavelength: 532nm
• LED Power: <SW
• Control Method: Remote Control
• Distance: <Sm (Optimum Range)
• Power Input: 100-240V-S0/60Hz 0.4A
• Working Input: SV 1A
• Product size: 120113228mm
• Use environment: indoor (better in dark environment) Operating temperature: -10° to 45°

FEATURES

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>