SAMMITR ST223L SteelTop Canopy User Guide
- June 15, 2024
- SAMMITR
Table of Contents
SAMMITR ST223L SteelTop Canopy
Product Information
Specifications
- Product Name: Canopy Wiring Guide
- Manufacturer: N/A
- Usage: Wiring guide for canopies
- Compatibility: Ford vehicles
Product Usage Instructions
The Canopy Wiring Guide is designed to assist auto electricians in properly wiring canopies in Ford vehicles. It is important to note that all wiring should be done by a trained professional to ensure safety and proper functionality.
Step 1: Gather the necessary tools
Before starting the wiring process, ensure you have the following tools:
- Wire cutters/strippers
- Electrical tape
- Wire connectors
- Test light or multimeter
Step 2: Locate the wires in the vehicle
Refer to the Ford documentation specific to your vehicle model to locate the
wires needed for the canopy wiring. The wiring guide does not provide specific
wire locations as it may vary depending on the vehicle.
Step 3: Plan the wiring layout
Prior to connecting any wires, it is important to plan the wiring layout.
Determine which wires are needed for various canopy components such as lights,
power outlets, or audio systems.
Step 4: Connect the wires
Using the wire cutters/strippers, carefully strip the insulation off the ends
of the wires. Connect the corresponding wires from the canopy components to
the identified wires in the vehicle using wire connectors. Ensure a secure and
proper connection is made.
Step 5: Test the connections
After connecting the wires, use a test light or multimeter to verify that the
connections are working correctly. This step is crucial to ensure proper
functionality and safety.
Step 6: Secure and insulate the wiring
Once all the connections have been tested and verified, secure the wiring
using zip ties or other suitable methods. Insulate any exposed wires with
electrical tape to prevent short circuits or damage.
Step 7: Double-check and finalize
Before finishing the installation, double-check all connections, ensure wires
are properly routed and secured, and that no loose or exposed wires are
present. Make any necessary adjustments or corrections before finalizing the
installation.
Step 29
Shows a continuation of the wiring with the same configurations as step 28,
leading to the next part of the installation process.
Step 30
Ground Wiring connect position (black) Take off the Cover at the Driver
side in order to connect the Black Wiring of the Harness Central Lock No.38
with the Vehicle Structure. Take off the Bolt by using wrench No.10
Step 31
Connect the Black Wiring (Ground) of the Harness Central Lock No.38 with
the Vehicle Structure and using wrench tighten.
Step 32
Running canopy wiring via vehicle wiring hole/pipe along under the chassis.
Step 33
Run the wiring through the hole of the vehicle floor and seal to protect
water leaking problem.
Step 34
The Step of wiring running diagram:
- Wiring running from driver side through passenger side.
- Running canopy wiring via vehicle wiring hole/pipe along under the chassis.
- Wiring that run under vehicle along the chassis.
- Wiring that run via chassis at the fender area.
- Wiring that running up the rear light in order to connect with the other wiring set.
The Step of wiring running diagram for the Harness Central Lock No.38
Step 35 & 36
Take off the Rear Light by using wrench No.10 and take off the Rear Light
vehicle.
Step 37
Running the Harness Central Lock No.38 up to the vehicle rear light in
order to connects with the Harness Central Lock No.32.
Step 38 & 39
Run the rod along the vehicle edge till the Rear vehicle light.
Step 40 & 41
Run the Harness Central Lock No.38 along the vehicle tub channel out of the
Rear Light Socket. Then, position the Harness Central Lock No.38 wiring set.
Step 42
Re-assembly Harness Central Lock No.38 of all positions back to the spots.
Step 43 & 44
Connecting the wires for Central Lock and Room Lamp.
Step 45 & 46
Connecting the wires for the Defogger and Third Brake Light.
Step 47 & 48
Connect the Red wiring, third Brake Light (RD) of the Harness Central Lock
No.38 with the Black Brake Light Wiring on the Left Side of the Rear vehicle
light. Then, connect position wiring Brake Light (Wildtrak).
Step 49 & 50
Tight up all the wiring by using the Cable Tie and take off the Rear Light
vehicle.
Step 51
Room Lamp checking by opening the rear door then the Room Lamp will be on.
Step 52 & 53
Check the Central Lock / Room Lamp working. Central Lock checking by
pressing the vehicle remote key at the Lock position, Canopy will be lock and
cannot open. Then, check by pressing the vehicle remote key at the Unlock
position, Canopy will be open.
Canopy Wiring Guide
Note: This is the wiring guide supplied by the manufacturer. All wiring should be completed by a trained auto electrician. Please refer to Ford documentation to locate the wires in the vehicle as required.
SMM SteelTop® Canopy
Instructions for wiring the SMM SteelTop® Canopy are provided through a
series of steps, each accompanied by a diagram for clarity. Take off the
Wiring Cover at the driver side in order to check the wiring position.
Wiring Configurations:
- LOCK (blue)
- UNLOCK (green)
- GROUND (Car)
- ROOM Lamp (5A) – red
- DEFOGGER (20 A)
- 12V Switch ON
Harness Central Lock No.38
Frequently Asked Questions (FAQ)
Can I wire the canopy myself?
It is highly recommended to have the wiring done by a trained auto electrician to ensure safety and proper functionality.
Where can I find the Ford documentation for my vehicle?
The Ford documentation can be found in the owner's manual or by contacting a Ford dealership for assistance.
Are there any specific precautions I should take during the wiring process?
Yes, always disconnect the vehicle's battery before starting any wiring work. This will prevent any accidental short circuits or electrical damage.
Can I perform the wiring installation myself?
All wiring should be completed by a trained auto electrician as per the manufacturer's guide.
Do I need to refer to any additional documentation?
Yes, you should refer to Ford documentation to locate the wires in the vehicle as required.
What tools are required for the installation?
A wrench, specifically No.10, is mentioned for use in steps 30, 35, and 36.
How can I ensure the wiring is protected from water damage?
Run the wiring through the hole of the vehicle floor and seal it to protect from water leaking problems as indicated in step 33.
How do I check if the Central Lock / Room Lamp is working correctly?
By pressing the vehicle remote key at the Lock and Unlock positions, you can check the functionality of the Central Lock and Room Lamp as described in steps 52 and 53.
Canopy Wiring Guide
SMM SteelTop® Canopy
Note: This is the wiring guide supplied by the manufacturer. All wiring should
be completed by a trained auto electrician. Please refer to Ford documentation
to locate the wires in the vehicle as required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>