inventronics ESM-880S280MGS 880W Programmable Driver with INV Digital Dimming User Manual

June 17, 2024
INVENTRONICS

inventronics-logo

inventronics ESM-880S280MGS 880W Programmable Driver with INV Digital

Dimming

Specifications:

  • Model: ESM-880SxxxMGS
  • Power: 880W
  • Output Current Range: 0.195-20.0 A
  • Output Voltage Range: Varies per model
  • Max. Output Power: 880W
  • Typical Efficiency: 95.0% – 96.0%
  • Typical Power Factor: 0.96 – 0.99
  • Input Voltage Range: 277Vac – 480Vac

Product Usage Instructions:

Installation:
Follow these steps to install the programmable driver:

  1. Ensure power is switched off before installation.
  2. Connect the driver to the power source within the input voltage range.
  3. Connect the output to the load following the specified current and voltage ranges.

Programming:
To program the driver:

  1. Refer to the model number and adjust the output current within the specified range.
  2. Ensure the output voltage is within the allowed operating area for optimal performance.

Dimming:
Utilize the INV Digital Dimming feature for dimming control:

  1. Follow the dimming instructions provided in the manual for proper dimming operation.

Frequently Asked Questions (FAQ):

  • Q: Can I use this driver with input voltage below 277Vac?
    A: The certified voltage range is UL, FCC 277-480Vac; however, it can also work within 277-400Vac.

  • Q: What is the warranty period for this product?
    A: The product comes with a 5-year warranty for added assurance.

  • Q: How do I determine the correct output current for my application?
    A: Refer to the model number and adjust the output current within the specified range based on your requirements.

Features

  • Panel Mount Connectors Facilitates Installation
  • Brackets Accommodates Variety of Hanging Applications
  • Ultra High Efficiency (Up to 96%)
  • Full Power at Wide Output Current Range (Constant Power)
  • Adjustable Output Current (AOC) with Programmability
  • Isolated 0-10V/PWM/3-Timer-Modes Dimmable
  • Adjustable Dimming Curve
  • INV Digital Dimming, UART Based Communication Protocol
  • Dim-to-Off with Standby Power
  • Minimum Dimming Level with 5% or 10% Selectable
  • Hold Time Adjustable
  • Fade Time Adjustable
  • Always-on Auxiliary Power: 12Vdc, 250mA
  • Low Inrush Current
  • Output Lumen Compensation
  • End-of-Life Indicator
  • Input Surge Protection: DM 6kV, CM 10kV
  • All-Around Protection: IUVP, IOVP, OVP, SCP, OTP
  • IP66/IP67 and UL Dry/Damp/Wet Location
  • TYPE HL, for Use in a Class I, Division 2 Hazardous (Classified) Location
  • 5 Years Warranty

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(1\) Description
The ESM-880SxxxMGS series is an 880W, constant-current, programmable and IP66/IP67 rated LED driver that operates from 249-528Vac input with excellent power factor. Created for many lighting applications including high mast, sports, UV-LED, aquaculture and horticulture, etc. It provides an auxiliary voltage and dim-to-off functionality for powering low voltage, wireless controls. The dimming control supports 0-10V dimming as well as two-way communication via Digital Dimming, a UART based communication protocol. The high efficiency of these drivers and compact metal case enables them to run cooler, significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input surge, input under voltage, input over voltage, output over voltage, short circuit, and over temperature.

Models

Adjustable Output Current

Range(A)

| Full-Power Current Range(A) (1)| Default Output Current(A)| Output Voltage Range(Vdc)| Max. Output Power(W)|

Typical Efficiency (2)

| Typical Power Factor|

Model Number (3)

---|---|---|---|---|---|---|---
277Vac| 480Vac
0.195-2.8| 1.95-2.8| 2.1| 157-452| 880| 96.0%| 0.99| 0.96| ESM-880S280MGS
0.300-4.2| 3.0-4.2| 4.2| 104-294| 880| 95.5%| 0.99| 0.96| ESM-880S420MGS
0.490-7.0| 4.9-7.0| 5.6| 63.0-180| 880| 96.0%| 0.99| 0.96| ESM-880S700MGS
0.800-11.5| 8.0-11.5| 8.4| 38.0-110| 880| 95.0%| 0.99| 0.96| ESM-880S11AMGS(4)
1.630-20.0| 16.3-20.0| 20.0| 22.0-54| 880| 95.5%| 0.99| 0.96| ESM- 880S20AMGS(4)

Notes:

  1. Output current range with constant power at 880W.
  2. Measured at 100% load and 480Vac input (see below “General Specifications” for details).
  3. Certified voltage range: UL, FCC 277-480Vac; otherwise 277-400Vac.
  4. SELV output

Operating Area

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(2\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(3\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(4\)

Input Specifications

Parameter Min. Typ. Max. Notes
Input AC Voltage 249 Vac 528 Vac
Input DC Voltage 352 Vdc 500 Vdc
Input Frequency 47 Hz 63 Hz
Leakage Current 0.75 MIU UL 8750; 480Vac/60Hz
0.70 mA IEC 60598-1; 480Vac/60Hz
Input AC Current 3.79 A Measured at 100% load and 277 Vac input.
2.16 A Measured at 100% load and 480 Vac input.
Inrush Current(I2t) 1.98 A2s At 480Vac input, 25°C cold start,

duration=6.6 ms, 10%Ipk-10%Ipk.
PF| 0.90| –| –| At 277-480Vac, 50-60Hz, 60%-100% Load (528-880W)
THD| –| –| 20%

Output Specifications

Parameter Min. Typ. Max. Notes
Output Current Tolerance -5%Ioset 5%Ioset 100% load

Output Current Setting(Ioset) Range

ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS

ESM-880S11AMGS ESM-880S20AMGS

|

195 mA

300 mA

490 mA

800 mA

1630 mA

|

|

2800 mA

4200 mA

7000 mA

11500 mA

20000 mA

|
Output Current Setting Range with Constant Power

ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS

ESM-880S11AMGS ESM-880S20AMGS

|

1950 mA

3000 mA

4900 mA

8000 mA

16300 mA

|

|

2800 mA

4200 mA

7000 mA

11500 mA

20000 mA

|
Total Output Current Ripple (pk-pk)| –| 5%Iomax| 10%Iomax| 100% load, 20 MHz BW
Output Current Ripple at

< 200 Hz (pk-pk)

| –| –| 2%Iomax| 70%-100% load
Startup Overshoot Current| –| –| 10%Iomax| 100% load
No Load Output Voltage

ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS ESM-880S11AMGS

ESM-880S20AMGS

|

|

|

500 V

350 V

200 V

120 V

60 V

|
Line Regulation| –| –| ±0.5%| 100% load
Load Regulation| –| –| ±1.5%|
Turn-on Delay Time| –| –| 0.5 s| Measured at 277-480Vac input, 60%- 100% Load
Parameter| Min.| Typ.| Max.| Notes
---|---|---|---|---
Temperature Coefficient of Ioset| –| 0.03%/°C| –| Case temperature = 0°C ~Tc max
12V Auxiliary Output Voltage| 10.8 V| 12 V| 13.2 V|
12V Auxiliary Output Source Current| 0 mA| –| 250 mA| Return terminal is “Dim−“
12V Auxiliary Output Transient Peak Current@6W| –| –| 500 mA| 500mA peak for a maximum duration of

2.2ms in a 6.0ms period during which time the average should not exceed 250mA.

12V Auxiliary Output Transient Peak Current@10W| –| –| 850 mA| 850mA peak for a maximum duration of 1.3ms in a 5.2ms period during which time the average should not exceed 250mA.

General Specifications

Parameter Min. Typ. Max. Notes
Efficiency at 277 Vac input:
ESM-880S280MGS
Io= 1950 mA 93.0% 95.0%
Io= 2800 mA 93.0% 95.0%
ESM-880S420MGS

Io= 3000 mA

Io= 4200 mA

| 92.0%

92.5%

| 94.0%

94.5%

| –

|

Measured at 100% load and steady-state

ESM-880S700MGS| | | | temperature in 25°C ambient;
Io= 4900 mA| 93.0%| 95.0%| –| (Efficiency will be about 2.0% lower if
Io= 7000 mA

ESM-880S11AMGS

| 92.5%| 94.5%| –| measured immediately after startup.)
Io= 8000 mA| 92.0%| 94.0%| –|
Io= 11500 mA| 92.0%| 94.0%| –|
ESM-880S20AMGS| | | |
Io= 16300 mA| 93.0%| 95.0%| –|
Io= 20000 mA| 92.5%| 94.5%| –|
Efficiency at 400 Vac input:| | | |
ESM-880S280MGS| | | |
Io= 1950 mA| 94.0%| 96.0%| –|
Io= 2800 mA| 94.0%| 96.0%| –|
ESM-880S420MGS| | | |
Io= 3000 mA

Io= 4200 mA

| 93.0%

93.5%

| 95.0%

95.5%

| –

| Measured at 100% load and steady-state
ESM-880S700MGS| | | | temperature in 25°C ambient;
Io= 4900 mA| 94.0%| 96.0%| –| (Efficiency will be about 2.0% lower if
Io= 7000 mA

ESM-880S11AMGS

| 93.5%| 95.5%| –| measured immediately after startup.)
Io= 8000 mA| 93.0%| 95.0%| –|
Io= 11500 mA| 93.0%| 95.0%| –|
ESM-880S20AMGS| | | |
Io= 16300 mA| 93.5%| 95.5%| –|
Io= 20000 mA| 93.0%| 95.0%| –|
Parameter| Min.| Typ.| Max.| Notes
---|---|---|---|---
Efficiency at 480 Vac input:| | | |
ESM-880S280MGS| | | |
Io= 1950 mA| 94.0%| 96.0%| –|
Io= 2800 mA| 94.0%| 96.0%| –|
ESM-880S420MGS| | | |
Io= 3000 mA

Io= 4200 mA

| 93.0%

93.5%

| 95.0%

95.5%

| –

|

Measured at 100% load and steady-state

ESM-880S700MGS| | | | temperature in 25°C ambient;
Io= 4900 mA| 94.0%| 96.0%| –| (Efficiency will be about 2.0% lower if
Io= 7000 mA

ESM-880S11AMGS

| 94.0%| 96.0%| –| measured immediately after startup.)
Io= 8000 mA| 93.0%| 95.0%| –|
Io= 11500 mA| 93.0%| 95.0%| –|
ESM-880S20AMGS| | | |
Io= 16300 mA| 93.5%| 95.5%| –|
Io= 20000 mA| 93.0%| 95.0%| –|
Standby Power| –| 1.5 W| –| Measured at 480Vac/50Hz; Dimming off

MTBF

|

| 217,000

Hours

|

| Measured at 480Vac input, 80%Load and

25°C ambient temperature (MIL-HDBK- 217F)

Lifetime

|

| 100,000

Hours

|

| Measured at 480Vac input, 80%Load and

70°C case temperature; See lifetime vs. Tc curve for the details

–| 50,000

Hours

| –| Measured at 277Vac input, 100%Load

and 40°C ambient temperature

Operating Case Temperature for Safety Tc_s| -40°C| –| +90°C|
Operating Case Temperature for Warranty Tc_w| -40°C| –| +80°C| Case temperature for 5 years warranty Humidity: 10%RH to 95%RH
Storage Temperature| -40°C| –| +85°C| Humidity: 5%RH to 95%RH
Dimensions

Inches (L × W × H) Millimeters (L × W × H)

| | With mounting ear
10.83 × 6.30 × 1.91| 11.81 × 6.30 × 1.91
275 × 160 x 48.5| 300 ×160 x 48.5
Net Weight| –| 3650 g| –|

Dimming Specifications

Parameter Min. Typ. Max. Notes
Absolute Maximum Voltage on the Vdim (+) Pin -20 V 20 V
Source Current on Vdim (+)Pin 200 uA 300 uA 450 uA Vdim(+) = 0 V

Dimming Output Range with 10%-100%

(Default)

| ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS

ESM-880S11AMGS ESM-880S20AMGS

| 10%Ioset| –| Ioset| 1950 mA ≤ Ioset ≤ 2800 mA 3000 mA ≤ Ioset ≤ 4200 mA 4900 mA ≤ Ioset ≤ 7000 mA
8000 mA ≤ Ioset ≤ 11500 mA 16300 mA ≤ Ioset ≤ 20000 mA
ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS ESM-880S11AMGS ESM-880S20AMGS| 195 mA

300 mA

490 mA

800 mA

1630 mA

| –| Ioset| 195 mA ≤ Ioset <1950 mA 300 mA ≤ Ioset <3000 mA 490 mA ≤ Ioset <4900 mA

800 mA ≤ Ioset <8000 mA 1630 mA ≤ Ioset <16300 mA

Parameter Min. Typ. Max. Notes

Dimming Output Range with 5%-100%

(Settable)

| ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS

ESM-880S11AMGS ESM-880S20AMGS

|

5%Ioset

|

|

Ioset

| 1950 mA ≤ Ioset ≤ 2800 mA 3000 mA ≤ Ioset ≤ 4200 mA 4900 mA ≤ Ioset ≤ 7000 mA

8000 mA ≤ Ioset ≤ 11500 mA 16300 mA ≤ Ioset ≤ 20000 mA

ESM-880S280MGS ESM-880S420MGS ESM-880S700MGS ESM-880S11AMGS ESM-880S20AMGS| 98 mA

150 mA

245 mA

400 mA

815 mA

|

|

Ioset

| 195 mA ≤ Ioset <1950 mA 300 mA ≤ Ioset <3000 mA 490 mA ≤ Ioset <4900 mA 800 mA ≤ Ioset <8000 mA

1630 mA ≤ Ioset <16300 mA

Recommended Dimming Input Range| 0 V| –| 10 V| Default 0-10V dimming mode.
Dim off Voltage| 0.35 V| 0.5 V| 0.65 V
Dim on Voltage| 0.55 V| 0.7 V| 0.85 V
Hysteresis| –| 0.2 V| –
PWM_in High Level| 3 V| –| 10 V| Dimming mode set to PWM in Inventronics Programing Software.
PWM_in Low Level| -0.3 V| –| 0.6 V
PWM_in Frequency Range| 200 Hz| –| 3 KHz
PWM_in Duty Cycle| 1%| –| 99%
PWM Dimming off (Positive Logic)| 3%| 5%| 8%
PWM Dimming on (Positive Logic)| 5%| 7%| 10%
PWM Dimming off ( Negative Logic)| 92%| 95%| 97%
PWM Dimming on ( Negative

Logic)

| 90%| 93%| 95%
Hysteresis| –| 2%| –

Safety &EMC Compliance

Safety Category Standard
UL/CUL UL 8750,CAN/CSA-C22.2 No. 250.13
ENEC & CE EN 61347-1, EN 61347-2-13
UKCA BS EN 61347-1, BS EN 61347-2-13
CB IEC 61347-1, IEC 61347-2-13
Performance Standard
ENEC EN 62384
EMI Standards Notes
BS EN/EN IEC 55015(1) Conducted emission Test &Radiated emission Test
BS EN/EN IEC 61000-3-2 Harmonic current emissions
EMI Standards Notes
--- ---
BS EN/EN 61000-3-3 Voltage fluctuations & flicker

FCC Part 15(1)

| ANSI C63.4 Class B
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2]

this device must accept any interference received, including interference that may cause undesired Operation.

EMS Standards| Notes
BS EN/EN 61000-4-2| Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact discharge
BS EN/EN 61000-4-3| Radio-Frequency Electromagnetic Field Susceptibility Test- RS
BS EN/EN 61000-4-4| Electrical Fast Transient / Burst-EFT
BS EN/EN 61000-4-5| Surge Immunity Test: AC Power Line: Differential Mode 6 kV, Common Mode 10 kV
BS EN/EN 61000-4-6| Conducted Radio Frequency Disturbances Test-CS
BS EN/EN 61000-4-8| Power Frequency Magnetic Field Test
BS EN/EN 61000-4-11| Voltage Dips
BS EN/EN 61547| Electromagnetic Immunity Requirements Applies To Lighting Equipment

Note:

  1. This LED driver meets the EMI specifications above, but EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself.

Lifetime vs. Case Temperature

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(5\)

Inrush Current Waveform

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(6\)

Efficiency vs. Load

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(7\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(8\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(9\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(10\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(11\)

Power Factor

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(12\)

Total Harmonic Distortion

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(13\)

Protection Functions

Parameter Min. Typ. Max. Notes
Over Temperature Protection Decreases output current, returning to normal

after over temperature is removed.
Short Circuit Protection| Auto Recovery. No damage will occur when any output is short circuited. The output shall return to normal when the fault condition is removed.
Over Voltage Protection| Limits output voltage at no load and in case the normal voltage limit fails.
Input Under Voltage Protection

(IUVP)

| Input Protection Voltage| 220 Vac| 230 Vac| 240 Vac| Turn off the output when the input voltage falls below protection voltage.
Input Recovery Voltage| 230 Vac| 240 Vac| 250 Vac| Auto Recovery. The driver will restart when the input voltage exceeds recovery voltage.
Input Over Voltage Protection (IOVP)| Input Over Voltage

Protection

| 550 Vac| 570 Vac| 590 Vac| Turn off the output when the input voltage exceeds protection voltage.
Input Over

Voltage Recovery

| 530 Vac| 550 Vac| 570 Vac| Auto Recovery. The driver will restart when the input voltage falls below recovery voltage.
Max. of Input Over Voltage| –| –| 590 Vac| The driver can survive for 8 hours with input voltage stress of 590Vac.

  • Input Under Voltage Protection Diagram
  • inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-Dimming- \(14\) Input Over Voltage Protection Diagram inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-Dimming- \(15\)

Dimming

10V Dimming
The recommended implementation of the dimming control is provided below .inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(16\) inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(17\)

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener.
  3. When 0-10V negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby.

PWM Dimming
The recommended implementation of the dimming control is provided below .inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(18\)

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. When PWM negative logic dimming mode and Dim+ is open, the driver will dim to off and be standby.

Adjustable Dimming Curve
0-10V dimming curve can be set as corresponding dimming voltage by Inventronics Multi Programmer. Take the positive logic dimming as an example, the recommended implementation of the dimming control is provided below .inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(19\)

Notes:

  1. Do NOT connect Dim− to the output V− or V+, otherwise the driver will not work properly.
  2. The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like zener.
  3. When dimming voltage X point is set to be smaller than Y point, the dimming curve is positive logic; conversely, when X point is set to be bigger than Y point, the dimming curve is negative logic.
  4. For best dimming accuracy, the difference between X point and Y point is advised more than 4V.
  5. Dimming off voltage adjustable.
  • Time Dimming
    Time dimming control includes 3 kinds of modes, they are Self Adapting- Midnight, Self Adapting-Percentage and Traditional Timer.

    • Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of past two days (if difference <15 minutes), assuming that the center point of the dimming curve is midnight local time.
    • Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) / (programmed on-time from the dimming curve).
    • Traditional Timer: Follows the programmed timing curve after power on with no changes.
  • Output Lumen Compensation
    Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation.

  • Minimum Dimming Level with 5% or 10% Selectable
    The minimum dimming level can be set as 5% or 10% by Inventronics Multi Programmer,10% is default.

  • Hold Time Adjustable
    When AC power is first applied to the LED driver, enabling a “Hold” period can allow devices powered by the Auxiliary voltage to stabilize before the driver fades up to the maximum dimming level. During this period, the driver will not respond to external dimming commands but will respond again after the hold time ends. Both the initial dimming percentage and the duration of this hold period can be adjusted by the Inventronics Multi Programmer. This function is disabled by default.

  • Fade Time Adjustable
    There is a “Fade” period after the “Hold” period. The soft-start time and dimming slope applied to all dimming transitions can be adjusted individually. It is adjusted by the Inventronics Multi Programmer. This function is disabled by default.

  • End Of Life
    End-of-Life (EOL) is providing a visual notification to a user that the LED module has reached the end of manufacturer-specified life and that the replacement is recommended. Once active, an indication is given at each power- up of the driver, which the driver indicates this through a lower light output during the first 1 minute before normal operation is continued.

  • Digital Dimming
    Inventronics Digital Dimming is a UART (Universal Asynchronous Receive Transmitter) based communication protocol. Please refer to Inventronics Digital Dimming file for details

Programming Connection Diagram

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(20\)

  • Please refer to PRG-MUL2 (Programmer) datasheet for details.

Mechanical Outline

inventronics-ESM-880S280MGS-880W-Programmable-Driver-with-INV-Digital-
Dimming- \(21\)

Note: This driver features UL Wet Location, IP67 panel mount connectors to streamline wiring in the field while still supporting stringent environmental conditions. The mating push-lock are not supplied by Inventronics. Please contact Wieland and Amphenol LTW or one of their suppliers for assistance sourcing the mating push-lock.

Location| Series| Rating voltage/current| PN of connector on driver| PN of mating push-lock
---|---|---|---|---
Vin| Wieland RST20i3| 600V/10A| 96.032.1055.7| 96.031.0055.7 (Spring)

or 96.031.4055.7 (Screw)

__

Vo

| __

ALTW X-Lok,C-Size

| 600V/10A| CC-03PMFS-QC801P| CC-03BFMB-QL8APA
300V/20A| CC-03PMFS-QC800P| CC-03BFMB-QL8APP
Dim| ALTW X-Lok,A-Size| 300V/5A| AD-03PMMS-QC8001| AD-03BFFB-QL8AP0
Dim| ALTW X-Lok,A-Size Waterproof Cap| /| CAP-WAAMQPC1| /

RoHS Compliance
Our products comply with reference to RoHS Directive (EU) 2015/863 amending 2011/65/EU, calling for the elimination of lead and other hazardous substances from electronic products.

Revision History

Change Date|

Rev.

| Description of Change
---|---|---
Item| From| To
2022-06-13| A| Datasheet Release| /| /

2024-01-09

|

B

| Format| /| Updated
Product Photograph| /| Updated
Features| /| Updated
Models| /| Updated
Inrush Current Waveform| /| Updated
Dimming| /| Updated
Mechanical Outline| /| Updated

Specifications are subject to changes without notice.
All specifications are typical at 25C unless otherwise stated.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals