INVENTRONICS 150W Programmable Outdoor Driver User Guide

June 7, 2024
INVENTRONICS

INVENTRONICS LOGO

ESD-150SxxxDT
150W Programmable Outdoor Driver

INVENTRONICS 150W Programmable

Features

  • Ultra-High Efficiency (Up to 94.5%)
  • Full Power at Wide Output Current Range (Constant Power)
  • Thermal Sensing and Protection for LED Module
  • 0-10V/PWM/Timer Dimmable (3 Timer Modes)
  • Dim-to-Off with Standby Power ≤ 1.5 W
  • Output Lumen Compensation
  •  Input Surge Protection: 6kV line-line, 10kV line-earth
  • All-Around Protection: OVP, SCP, OTP
  • Suitable for UL Dry / Damp / Wet Location
  • TYPE HL, for use in Class I, Division 2 hazardous
    (Classified) location

Description

The ESD-150SxxxDT series is a 150W, constant-current, programmable LED driver that operates from 249-528 Vac input with excellent power factor. Created for high bay,  tunnel and roadway lights, it provides a dim-off mode with low standby power. The high efficiency of these drivers and compact metal case enables them to run cooler,  significantly improving reliability and extending product life. To ensure trouble-free operation, protection is provided against input surge, output over-voltage, short circuit, and over temperature.

Models

Adjustable
Output
Current
Range| Full-Power
Current
Range (1)| Default
Output
Current| Input
Voltage
Range (2)| Output
Voltage
Range| Max.
Output
Power| Typical
Efficiency
(3)| Power Factor| Model Number
---|---|---|---|---|---|---|---|---
277Vac| 480Vac
70-1050mA| 700-1050mA| 700 mA| 249-528 Vac
352-600 Vdc| 75-214Vdc| 150 W| 94.5%| 0.96| 0.95| ESD-150S105D1
140-2100mA| 1400-2100mA| 1400 mA| 249-528 Vac
352-600 Vdc| 38-107Vdc| 150 W| 94.0%| 0.96| 0.95| ESD-150S210DT
245-3500mA| 2450-3500mA| 2800 mA| 249-528 Vac
352-600 Vdc| 22 — 61Vdc| 150 W| 93.0%| 0.96| 0.95| ESD-150S350D1
385-5600mA| 3850-5600mA| 4200 mA| 249-528 Vac
352-600 Vdc| 14 — 39Vdc| 150 W| 93.0%| 0.96| 0.95| ESD-150S560D1

Notes: (1) Output current range with constant power at 150W
(2) Certified input voltage range: 277-480Vac or 352-600Vdc
(3) Measured at full load and 480Vac input (see below “General Specifications” for details).

I-V Operating Area

INVENTRONICS 150W Programmable -I-V Operating Area

Specifications are subject to changes without notice.

Input Specifications

Parameter Min. Typ. Max. Notes
Input Voltage 249 Vac 528 Vac 352-600 Vdc
Input Frequency 47 Hz 63 Hz
Leakage Current 1.0 MIU At 480Vac/60Hz input, grounding effectively
Input AC Current 0.70 A Measured at full load and 277 Vac input.
0.40 A Measured at full load and 480 Vac input.
Inrush Current(12t) 7.6 A2s At 480Vac input, 25°C Cold Start,

Duration=680 us, 10%Ipk-10%Ipk. See Inrush Current Waveform for the details.
PF| 0.90| –| –| At 277-480Vac, 50-60Hz, 60%-100% Load (90-150W)
THD| –| –| 20%

Output Specifications

Parameter Min. Typ. Max. Notes
Output Current Tolerance -5%loset 5%loset At full load condition

Output Current Setting(loset) Rang
ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT| 70 mA 140 mA 245 mA 385 mA| – – – –| 1050 mA 2100 mA 3500 mA 5600 mA|
Output Current Setting Range with Constant Power
ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT| 700 mA 1400 mA 2450 mA 3850 mA| – – – –| 1050 mA 2100 mA 3500 mA 5600 mA|
Total Output Current Ripple (pk-pk)| –| 5%lomax| 10%lomax| At full load condition, 20 MHz BW
Output Current Ripple at < 200 Hz (pk-pk)| –| 2%lomax| –| At full load condition. Only this component of ripple is associated with visible flicker.
Startup Overshoot Current| –| –| 10%lomax| At full load condition
No Load Output Voltage
ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT| | – – – –| 223 V 116 V 64 V 43 V|
Line Regulation| | | ±–0.5%| Measured at full load
Load Regulation| | | +1.5%|
Turn-on Delay Time| | 0.8 s| 1.5 s| Measured at 277Vac and 480Vac input, 60%-100% Load
Temperature Coefficient of loset| | 0.03%/°C| | Case temperature = 0°C -Tc max
12V Auxiliary Output Voltage (Vaux)| 10.8 V| 12 V| 13.2 V|
12V Auxiliary Output Source Current (laux)| 0 mA| –| 200 mA| Return terminal is –Dim-–

Note: All specifications are typical at 25°C unless otherwise stated.

General Specifications

Parameter Min. Typ. Max. Notes

Efficiency at 277 Vac input: ESD-150S105DT
lo= 700mA
1o=1050mA
ESD-150S210DT
lo=1400mA
lo=2100mA
ESD-150S350DT
lo=2450mA
lo=3500mA
ESD-150S560DT
lo=3850mA
1o=5600mA| 91.5%
89.5%91.0%
90.0%

91.0%
89.0%

90.5%
88.0%

| 93.5%
91.5%93.0%
92.0%

93.0%
91.0%

92.5%
90.0%

| –



| Measured at full load and steady-state temperature in 25°C ambient;

(Efficiency will be about 2.0% lower if measured immediately after startup.)

Parameter Min. Typ. Max. Notes

Efficiency at 347 Vac input: ESD-150S105DT
lo= 700mA
lo=1050mA
ESD-150S210DT
lo=1400mA
lo=2100mA
ESD-150S350DT
lo=2450mA
lo=3500mA
ESD-150S560DT
lo=3850mA
1o=5600mA| 92.0%
90.5%91.5%
90.5%

91.5%
89.5%

90.5%
88.5%

| 94.0%
92.5%93.5%
92.5%

93.5%
91.5%

92.5%
90.5%

| –



| Measured at full load and steady-state temperature in 25°C ambient;

(Efficiency will be about 2.0% lower if measured immediately after startup.)

Efficiency at 480 Vac input: ESD-150S105DT
1o= 700mA
1o=1050mA
ESD-150S210DT
lo=1400mA
lo=2100mA
ESD-150S350DT
lo=2450mA
lo=3500mA
ESD-150S560DT
lo=3850mA
1o=5600mA| 92.5%
91.0%92.0%
91.0%

91.0%
90.0%

91.0%
89.0%

| 94.5%
93.0%94.0%
93.0%

93.0%
92.0%

93.0%
91.0%

| –


| Measured at full load and steady-state temperature in 25°C ambient;
(Efficiency will be about 2.0% lower if measured immediately after startup.)
Standby power| –| –| 1.5 W| Measured at 480Vac/50Hz; Dimming off
MTBF| –| 203,000
Hours| –| Measured at 480Vac input, 80%Load and 25°C ambient temperature (MIL- HDBK­217F)
Lifetime| | 75, 000
Hours| | Measured at 480Vac input, 80%Load and 70°C case temperature with laux=100mA; See lifetime vs. Tc curve for the details
Operating Case Temperature for Safety Tc_s| -40°C| –| +88°C|
Operating Case Temperature for Warranty Tc w| -40°C| | +75°C|
Storage Temperature| -40°C| –| +85°C| Humidity: 5%RH to 100%RH
Dimensions
Inches (L x W x H) Millimeters (L x W x H)| 8.70 x 2.66 x 1.56
221 x 67.5 x 39.7| With mounting ear
9.53 x 2.66 x 1.56
242 x 67.5 x 39.7
Net Weight| –| 1300 g| –|

Note: All specifications are typical at 25ºC unless otherwise stated.

Dimming Specifications

Parameter Min. Typ. Max. Notes
Absolute Maximum Voltage on the Vdim (+) Pin -20 V 20 V
Source Current on Vdim (+)Pin 200 uA 300 uA 450 uA Vdim(+) = 0 V

Dimming Output

Range

| ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT| 10%loset| –| loset| 700mA C loset C 1050mA 1400mA C loset C 2100mA 2450mA C loset r::: 3500mA 3850mA ,c; loset z7r: 5600mA
ESD-150S105DT ESD-150S210DT ESD-150S350DT ESD-150S560DT| 70mA 140mA 245mA 385mA| –| loset| 70mA ( loset < 700mA 140mA ( loset < 1400mA 245mA ( loset < 2450mA 385mA c: loset < 3850mA
Recommended Dimming Input Range| 0 V| –| 10 V| Default 0-10V dimming mode.
Dim off Voltage| 0.35 V| 0.5 V| 0.65 V
Dim on Voltage| 0.55 V| 0.7 V| 0.85 V
Hysteresis| –| 0.2 V| –
PWM_in High Level| 3 V| –| 10 V| Dimming mode set to PWM in PC interface.
PWM_in Low Level| -0.3 V| | 0.6 V
PWM_in Frequency Range| 200 Hz| | 3 KHz
PWM_in Duty Cycle| 1%| | 99%
PWM Dimming off (Positive Logic)| 2%| 5%| 8%
PWM Dimming on (Positive Logic)| 4%| 7%| 10%
PWM Dimming off ( Negative Logic)| 92%| 95%| 98%
PWM Dimming on ( Negative Logic)| 90%| 93%| 96%
Hysteresis| –| 2%| –

Note: All specifications are typical at 25 ºC unless stated otherwise.

Safety & EMC Compliance

Safety Category Standard
UL/CUL UL8750,CAN/CSA-C22.2 No. 250.13
EMI Standards Notes
FCC Part15(1) ANSI C63.4 Class B

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: [1] this device may not cause harmful interference, and [2] this device must accept any interference received, including interference that may cause undesired operation.

Note: (1) This LED driver meets the EMI specifications above, but the EMI performance of a luminaire that contains it depends also on the other devices connected to the driver and on the fixture itself.

EMS Standards Notes
EN 61000-4-2 Electrostatic Discharge (ESD): 8 kV air discharge, 4 kV contact

discharge
EN 61000-4-3| Radio-Frequency Electromagnetic Field Susceptibility Test-RS
EN 61000-4-4| Electrical Fast Transient / Burst-EFT
EN 61000-4-5| Surge Immunity Test: AC Power Line: line to line 4 kV, line to earth 6 kV
EN 61000-4-6| Conducted Radio Frequency Disturbances Test-CS
EN 61000-4-8| Power Frequency Magnetic Field Test
EN 61000-4-11| Voltage Dips
EN 61547| Electromagnetic Immunity Requirements Applies To Lighting Equipment

Lifetime vs. Case Temperature

INVENTRONICS 150W Programmable - Case TemperatureInrush Current Waveform

INVENTRONICS 150W Programmable -Inrush Current
Waveform

Efficiency vs. Load

INVENTRONICS 150W Programmable - Efficiency 1| INVENTRONICS 150W Programmable - Efficiency
---|---

Power Factor

INVENTRONICS 150W Programmable - Power FactorTotal Harmonic Distortion

INVENTRONICS 150W Programmable - Harmonic
DistortionProtection Functions

Parameter Notes
Over Temperature Protection Decreases output current, returning to normal

after over temperature is removed.
Short Circuit Protection| Auto Recovery. No damage will occur when any output is short-circuited. The output shall return to normal when the fault condition is removed.
Over Voltage Protection| Limits output voltage at no load and in case the normal voltage limit fails.
External
Thermal
Protection
NTC| R1| –| 7.81 kOhm| –| When R NTC falls below R1, External Thermal Protection is triggered, reducing output current until R2 is reached.
R2| –| 4.16 kOhm| –| When R NTC is less than R2, the output current is reduced to the programmed “Protection Current Floor.”
Protection
Current Floor| 10%loset| 60%loset| 100%loset| 10%loset>lomin (default setting is 60%)
login| 60%loset| 100%loset| 10%losetslomin (default setting is 60%)

Dimming

0-10V Dimming
The recommended implementation of the dimming control is provided below.

INVENTRONICS 150W Programmable - Harmonic 1

Notes:

  1.  The dimmer can also be replaced by an active 0-10V voltage source signal or passive components like resistors and Zener.
  2.  Do NOT connect Dim− to the output V− or V+, otherwise, the driver will not work properly.
  3. If 0-10V dimming is not used, Dim + should be open.

PWM Dimming

INVENTRONICS 150W Programmable - PWM Dimming

  • Time Dimming
    Time dimming control includes 3 kinds of modes, they are Self Adapting- Midnight, Self AdaptingPercentage, and Traditional Timer.=
    • Self Adapting-Midnight: Automatically adjusts the dimming curve based on the on-time of the past two days (if the difference <15 minutes), assuming that the center point of the dimming curve is midnight local time.
    • Self Adapting-Percentage: Automatically adjusts the on-time of each step by a constant percentage = (actual on-time for the past 2 days if difference <15 min) /  (programmed on-time from the dimming curve).
    • Traditional Timer: Follows the programmed timing curve after power on with no changes.

  • Output Lumen Compensation
    Output Lumen Compensation (OLC) may be used to maintain constant light output over the life of the LEDs by driving them at a reduced current when new, then gradually increasing the drive current over time to counteract LED lumen degradation.

Programming Connection Diagram

INVENTRONICS 150W Programmable - Connection Diagram

Note: The driver does not need to be powered on during the programming process.

  • Please refer to the PRG-MUL2 Multi-Programmer datasheet for details.

Mechanical Outline

INVENTRONICS 150W Programmable -Mechanical Outline

RoHS Compliance

Our products comply with the European Directive 2011/65/EC, calling for the elimination of lead and other hazardous substances from electronic products.

Revision History

Change
Date
| Rev.| Description of Change
---|---|---
Item| From| To
2015-09-23| A| Datasheets Release| /| /
2016-06-02| B| Input AC Current| /| Updated
General Specifications| With mounting ear| Added
General Specifications| Net Weight| Added
Safety &EMC Compliance| Notes| Added
Programming Connection Diagram| /| Updated
Mechanical Outline| /| Updated
2017-08-03| C| Features| /| Updated
Input Specifications| PF/THD| Updated
Output Specifications| Turn-on Delay Time| Updated
Output Specifications| Temperature Coefficient of lost| Updated
Safety & EMC Compliance| /| Updated
Mechanical Outline| /| Updated

Specifications are subject to changes without notice.

www.inventronics-co.com

Tel: 86-571-56565800
Fax: 86-571-86601139
sales@inventronics-co.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals