RACK HUB XL Antler Bar Antler Mount Instructions

: June 17, 2024
: RACK HUB

Table of Contents

XL Antler Bar Antler Mount
Specifications:
Product Usage Instructions:
1. Installing XL Antler Insert:
2. Mounting XL Antler Bar:
3. Recommended Tools:
- FAQ:
Q: What should I do if the hole drilled is improper?
Q: Where can I find more information or installation
Q: How do I share feedback or photos of product usage?

XL Antler Bar Antler Mount

“`html

Specifications:

Product Name: XL Antler Bar
Manufacturer: Rack Hub
Material: Metal
Package Includes: XL Antler Bar, 1/2 Drill Bit, XL Antler
Insert

Product Usage Instructions:

1. Installing XL Antler Insert:

Install the XL INSERT ASSIST into the XL ANTLER INSERT.
Using a hammer, tap the XL ANTLER INSERT into the antler.
Grip the XL INSERT ASSIST, twist it and remove it.

2. Mounting XL Antler Bar:

Secure your antler with the pedicle facing in an upright
position.
Before drilling, mark your drill bit at 1 1/2 inches.
Using the provided 1/2 drill bit, drill a hole starting at the
center of the pedicle using the beam as an angle reference.
Slide the antler onto the hex end of the XL Antler Bar by
aligning the bar with the XL Antler Insert.
Tighten the XL Antler Bar slightly if needed to adjust your
angle.

3. Recommended Tools:

Power drill
1/4 Hex driver
Rubber mallet
Safety glasses
Vise
Towel (for wrapping antlers while drilling)
Saw or grinder (for exceptionally rough pedicles)

FAQ:

Q: What should I do if the hole drilled is improper?

A: An improperly drilled hole may require
adding adhesive to the antler insert for proper installation.

Q: Where can I find more information or installation

videos?

A: Visit our website at www.rack-hub.com for more information
and online installation videos.

A: Please use #RackHub when sharing your photos
on social media. We appreciate your feedback and would love to see
how our products are being used.

“`

3 PLEASE INCLUDE IN STEP

XL INSERT ASSIST
The XL INSERT ASSIST was designed specifically for the XL ANTLER INSERT. This NEW TOOL will assist you while installing the inserts into the antler. This part is meant for installation only and you can keep it for future usage. For questions, please check our RACK HUB® youtube channel or contact us via our website:
www.rack-hub.com

XL INSERT ASSIST

Install the XL INSERT ASSIST into the XL ANTLER INSERT.

XL ANTLER INSERT

Using a hammer, tap the XL ANTLER INSERT into the antler.
Grip the XL INSERT ASSIST, twist it and remove it.

XL ANTLER BAR INStRUCTIONS.
caution
sharp objects inside
Please follow these instructions. Your antlers will thank you.

PACKAGE INCLUDES.
– XL Antler Bar – 1/2″ Drill Bit – XL Antler Insert – (Antlers not included)

TOOLS NEEDED
or RECOMMENDED.
– Power drill – 1/4″ Hex driver – Rubber mallet – Safety glasses – Vise – Towel (something soft to wrap antlers while drilling) **Saw or grinder for
exceptionally rough pedicles
Failure to use the recommended products and procedures could result in improper installation or cause serious injury.

3 Starting with the small end, place the XL Antler Insert into the drilled hole. Press the insert in until it’s snug, and then find a rubber mallet. Using the mallet, gently tap the insert into the antler until the top lip of the insert touches the antler base.

4 Find a solid surface to mount your XL Antler Bar. This Antler Bar can be installed into a flat surface or vertical surface. (Optional: Use a drill with a 3/8″ or 7/16″ bit to pre-drill a hole into the desired surface). Use a 1/4″ Hex driver to install the XL Antler Bar. (If you’re installing it to drywall, be sure to fasten the product to a stud for a secure mount).

XL antler insert

Note: It helps to install the XL ANTLER BAR into the Antler prior to installation. You can align the XL ANTLER BAR at the proper angle prior to installing it into the desired surafce.

1 Secure your antler with the pedicle (base) facing in an upright position. (We recommend wrapping something soft around the antler and placing it in a vise).
VERSATILITY

2 Before drilling, mark your drill bit with a 1″ marking (2A- shown below). Using the provided 1/2″ drill bit, drill a hole starting at the center of the pedicle using the beam as an angle reference. The hole should be 1 1/2″ in depth. Line up the beam from a few angles prior to drilling (do this to avoid drilling completely through the antler).
slower speed

5 Slide the antler onto the hex end of the XL Antler Bar by aligning the bar with the XL Antler Insert (mating hex features). Slide the antler down until it’s fully engaged on the XL Antler Bar. Now you can tighten the XL Antler Bar slightly if needed to adjust your angle. Note: Because this is a hex feature, you have six sides of antler angle adjustment.

drilling

Hex on
XL Antler Bar
1/4″ Socket Driver

mount shed antlers or cut-off antlers.
2a mark the drill bit at 1 1/2″
We recommend using tape, paint, or a marker to stripe the drill bit at 1 1/2″ from the tip.
1 1/2″ Deep
An improperly drilled hole may result in the need to add an adhesive to the antler insert.

patent pending

Visit our website for more information or to see our online installation video.
www.rack-hub.com

You have now successfully installed your RACK HUB® product. Remember, your antler(s) can be removed at any time, and we highly encourage that interaction. We do sell extra XL Antler Inserts in case you have extra antlers.
thank you!

Keep in touch, and follow us on our social media platforms. We would love to hear your feedback and see how our products are being used. We strive for quality, and we can only do that with your help. Please use #RackHub when sharing your photos.